Question about 1997 Volkswagen Jetta

1 Answer

Timing belt 3 gears markings alignment

Changed the water pump but removed the timing lower 2 gears. Now I don't know where where he marking align. Can you help?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 67 Answers

What engine do you have?

Posted on Jun 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i check the timing marks on A TOYOTA CAMRY 2 LITER 4 CYLINDER 1995 model car ?


I have attached to where you align the notch for the cam gear. The harmonic balancer has a notch on it, which you align to the "0" on the lower cover. The belt has alignment marks on them normally crank gear is the dotted line and the cam will be the solid line. Don't reuse an old timing belt of you removed it without marking it first. You should have aligned the gears to there timing spots prior to removing the belt Be very careful if you have to rotate the cam or crank the Pistons can touch the valves and cause damage. Hope this helps.
1_29_2016_12_10_45_pm.png

Jan 29, 2016 | 1995 Toyota Camry

2 Answers

Timming belt broke from water pump broke while driving car put new water pump on n timming belt but car doesnt start right plus shakes doesnt sound right 2001 neon dodge


Sounds like timing belt not on correctly. Check timing marks are aligned correctly when installing timing belt. This vehicle should have 2-3 marks to be aligned when installing belt.marks should be on cam gear/ crankshaft gear and intermediate shaft if engine is equipped with it.

Sep 10, 2011 | Dodge Neon Cars & Trucks

1 Answer

Need to know timing marks


REMOVAL
1. Disconnect negative battery cable.
2. Loosen power steering lock bolts and nuts accordingly and remove tension from power steering (P/S) and/or air conditioning (A/C) compressor drive belt.
3. Remove P/S and/or A/C drive belt.
4. Loosen generator mounting bolts and adjusting bolt.
5. Remove generator bolts.
6. Remove water pump pulley.
7. Remove crankshaft pulley.
8. Remove upper and lower timing belt covers.
9. Turn crankshaft so that timing mark on timing belt pulley is aligned with timing mark on engine.
10. Check that "I" mark on intake camshaft pulley is aligned with mark on seal plate and "E" mark on exhaust camshaft pulley is aligned with mark on seal plate.
Do not move camshaft or crankshaft once timing marks have been correctly positioned.
11. Loosen tensioner pulley lock bolt.
12. Protect timing belt with a rag.
13. Remove tensioner pulley.
14. Remove timing belt. Mark the direction of timing belt rotation (on the timing belt) for proper reinstallation.

INSTALLATION
1. Install tensioner pulley. Replace tensioner spring whenever timing belt is replaced.
2. Pull tensioner pulley to its furthest point and tighten lock bolt.
3. Check that timing mark on timing belt pulley is aligned with timing mark on engine.
4. Check that "I" mark on intake camshaft pulley is aligned with mark on seal plate and "E" mark on exhaust camshaft pulley is aligned with mark on seal plate.
If existing timing belt is being reused, install belt in proper rotation direction marked prior to removal.
5. Install timing belt onto timing belt pulley first, then idler pulley, exhaust camshaft pulley, intake camshaft pulley, and tensioner pulley in that order.
6. Check that there is no looseness in belt between idler pulley and exhaust camshaft pulley or between intake and exhaust camshaft pulleys.
7. Loosen tensioner pulley lock bolt and allow tensioner spring to apply tension to timing belt.
Do not add additional tension.
8. Tighten tensioner pulley lock bolt to specified torque.
Tightening torque:28~38 lb-ft (38~51 N·m, 3.9~5.2 kg-m)
9. Rotate crankshaft two full revolutions (clockwise only) and align timing mark on timing belt pulley with timing mark on engine block.
10. Check that "I" mark on intake camshaft pulley and "E" mark on exhaust camshaft pulley are aligned with marks on seal plate.
11. If they are not aligned, remove timing belt and start process from tensioner installation.
12. Measure timing belt deflection by applying moderate pressure midway between camshaft pulleys. If deflection is not correct, repeat from tensioner installation.
Deflection pressure:22 Ib. (98 N, 10 kg)Deflection:0.39~0.50 in. (11~13 mm)
13. Install lower and upper timing belt covers in that order.
Tightening torque:5.8~8.0 Ib-ft (7.9~10.7 N·m, 0.8~1.1 kg-m)
14. Install timing belt guide plate and crankshaft pulley.
Tightening torque:9.0~12.6 lb-ft (12.3~17.2 N·m, 1.3~1.8 kg-m)
15. Install water pump pulley.
Tightening torque:9.0~12.6 lb-ft (12.3~17.2 N·m, 1.3~1.8 kg-m)
16. Install generator belt and adjust the tension.
17. Install P/S and/or A/C drive belt and adjust the tension.
18. Connect negative battery cable.

INSPECTION
Never forcefully twist, turn inside out or bend timing belt. Do not allow oil or grease to come in contact with timing belt.
1. Replace timing belt if it is contaminated with oil or grease.
2. Check timing belt for uneven wear, fraying, peeling, cracking and hardening. Replace timing belt as necessary.
3. Bend timing belt into a "U" shape as shown in figure. Distance "A" must be at least 1.0 in (25 mm).
4. Inspect both idler pulley and tensioner pulley for uneven wear and smooth bearing operation.
5. Inspect camshaft pulleys and timing belt pulley for broken teeth or damage.
Replace any component that shows damage, excessive wear, or that appears prone to a possible failure.

Feb 26, 2011 | 2002 Kia Spectra

2 Answers

On 2000 mazda protege 1.6 replaced water pump now won't start, thinking timing now out what is timing procedure?


i dont have a more detailed picture of setting the timing marks for the belt so i hope this helpsonetufshoppe_81.gif

Jan 30, 2011 | 2000 Mazda Protege

2 Answers

Timing belt


TIMING BELT & SPROCKETS R & I
NOTE: Some procedures may differ slightly due to engine
construction.
Removal
1) Remove all necessary air ducts. Position No. 4 piston at
TDC of compression stroke. Align timing marks. See Fig. 2. Remove fan
and fan shroud. Remove belts. If necessary, remove radiator and
splashguard.
2) Prevent engine from rotating and remove crankshaft timing
pulley retaining bolt. Remove upper and lower timing belt covers.
Remove spring from tension pulley. Loosen adjusting bolt and move
pulley toward water pump. Remove timing belt.
CAUTION: Ensure pistons are at TDC when rotating camshaft or damage
may result.
Inspection
1) Handle timing belt carefully. Avoid twisting or kinking
belt. Do not allow belt to become contaminated by water, oil, dirt or
other contaminates. Inspect belt for cracks or damage. If necessary,
replace.
2) Measure tension pulley spring length and force. Spring
length should not exceed 2.76" (70.2 mm) and spring force should not
be less than 197-347 lbs. (27-48 kg).
3) Replace tension pulley spring if not within specification.
Installation
1) Pull tensioner fully toward water pump side and
temporarily tighten retaining bolt. Ensure No. 4 cylinder is at TDC on
compression stroke by rotating crankshaft until keyway aligns with
mark on front crankshaft seal housing (12 o'clock). Rotate camshaft
until timing mark on cam gear (arrow) aligns with mark on upper
camshaft cover (notch). See Fig. 2.
NOTE: When timing marks are aligned as stated above, No. 4 piston
is at TDC on compression stroke.
2) Position timing belt over crankshaft sprocket, oil pump
sprocket, camshaft sprocket and tensioner in that order. Ensure belt
is positioned in sequence given and without slack between sprockets.
Loosen tension sprocket adjusting bolt allowing spring tension to
tighten belt. Tighten adjusting bolt temporarily.
3) Temporarily install crankshaft pulley bolt and rotate
crankshaft 2 complete revolutions in opposite direction of engine
rotation, until marks on crankshaft and front oil seal retainer are
aligned again. See Fig. 2. Loosen tensioner lock bolt, allowing
tesioner spring to fully adjust tension. Tighten tensioner lock bolt.
4) Install timing belt covers. To complete installation,
reverse removal procedures. Tighten all bolts to specification. See
TORQUE SPECIFICATIONS table at end of this article.
Fig. 2: 2.3L & 2.6L Timing Alignment Marks
Courtesy of Isuzu Motor Co

Dec 13, 2010 | 1989 Isuzu Pickup 2WD

1 Answer

How to replace timing belt on a 1992 pontiac sunbird


1989–92 VEHICLES
  1. Disconnect the negative battery cable.
  2. Remove the serpentine belt and timing belt cover.
  3. Loosen the water pump bolts and release tension with tool J–33039 or equivalent.
  4. Raise and support the vehicle safely.
  5. Remove the crankshaft pulley.
  6. Carefully lower the vehicle, then remove the timing belt. Fig. 11: Exploded view of the timing belt assembly — 1989–92 OHC engines 87953118.gif
    To install:
  7. Turn the crankshaft and the camshaft gears clockwise to align the timing marks on the gears with the timing marks on the rear cover.
  8. Install the timing belt, making sure the portion between the camshaft gear and crankcase gear is in tension.
  9. Using tool J–33039 or equivalent, turn the water pump eccentric clockwise until the tensioner contacts the high torque stop. Tighten the water pump screws slightly.
  10. Turn the engine by the crankshaft gear bolt 720°to fully seat the belt into the gear teeth.
  11. Turn the water pump eccentric counterclockwise until the hole in the tensioner arm is aligned with the hole in the base.
  12. Tighten the water pump screws to 18 ft. lbs. (24 Nm), while checking that the tensioner holes remain as adjusted in the prior step.
  13. Install the crankshaft pulley, timing belt cover and the serpentine drive belt.
1993–94 VEHICLES
  1. Disconnect the negative battery cable, then partially drain and recover the cooling system.
  2. Remove the coolant recovery reservoir.
  3. If equipped, remove the A/C belt.
  4. Remove the serpentine belt.
  5. Disconnect the evaporative emission pipe assembly.
  6. Remove the crankshaft pulley assembly.
  7. As outlined earlier, remove the timing belt front cover.
  8. Align the marks on the crankshaft sprocket with the marks on the rear timing belt cover by rotating the crankshaft.
  9. Loosen the water pump retaining bolts, and release the tension with tool J 33039-A or equivalent.
  10. Carefully lower the vehicle, then remove the timing belt. Fig. 12: Timing belt installation and tightening specifications — 1993–94 2.0L OHC engines 87953119.gif
    To install:
  11. Turn the crankshaft and camshaft gears clockwise to align the timing marks on the gears with the timing marks on the rear cover.
  12. Install the timing belt, making sure that the portion between the camshaft gear and crankshaft gear is in tension.
  13. Using tool J 33039-A, or equivalent adjustment tool, turn the coolant pump eccentric clockwise until the tensioner arm contacts the high torque stop. Tighten the water pump screws slightly.
  14. Turn the engine by the crankshaft gear bolt 720°clockwise to fully seat the belt into the gear teeth.
  15. Turn the coolant pump eccentric counter clockwise until the hole in the tensioner arm is aligned with the hole in the base. This must be done with the engine at room temperature, approximately 68°F (20°C).
  16. Tighten the water pump screws while checking that the tensioner holes remain as adjusted as in step 15.
  17. As outlined earlier, install the timing belt cover.
  18. Install the crankshaft pulley.
  19. Connect the evaporative emission pipe assembly.
  20. Install the serpentine drive belt and the A/C belt (if equipped).
  21. Install the coolant recovery reservoir.
  22. Properly fill the cooling system, then connect the negative battery cable.
prev.gif next.gif

Aug 11, 2010 | 1992 Pontiac Sunbird

2 Answers

Looking for timing mark's for a 1997 camry with a 2.2 4cyl motor?


Hi,


You find the timing marks on the picture below.

moz-screenshot-2.pngaab8238.jpg



Removal
Remove auxiliary 1. drive belts.
2. Support engine.
Remove:
Engine mounting and bracket.
Timing belt upper cover [1].
3.
4. Turn crankshaft clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Remove:
Crankshaft pulley bolt [4].
Crankshaft pulley [5]. Use tool No.09213-60017.
5.
6. Ensure timing marks aligned [2] & [3].
7. Slacken tensioner bolt [6]. Move tensioner away from belt and lightly tighten bolt.
Remove:
Timing belt lower cover [7].
Crankshaft sprocket guide washer [9].
Timing belt.
Tensioner pulley.

Installation
Installation
1. Check tensioner pulley for smooth operation.
2. Check free length of tensioner spring is 46,0 mm [8]. Replace spring if necessary.
3. Fit tensioner and spring. Ensure spring is connected correctly.
4. tighten bolt [6].
5. Ensure timing marks aligned [2] & [3].
6. Fit timing belt. Ensure belt is taut between sprockets.
Install:
Crankshaft sprocket guide washer [9].
Timing belt lower cover [7].
Crankshaft pulley [5].
7.
8. Slacken tensioner bolt 1/2 turn [6].
9. Turn crankshaft two turns clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Turn crankshaft slowly 1 7/8 turns clockwise until crankshaft pulley timing mark [3] aligned with 45° BTDC mark [10] on
timing belt lower cover [7].
10.
11. Tighten tensioner bolt [6]. Tightening torque: 42 Nm.
12. Install components in reverse order of removal.
13. Tighten crankshaft pulley bolt [4]. Tightening torque: 108 Nm.
Manufacturer: Toyota

Jun 25, 2010 | 1997 Toyota Camry

3 Answers

Timing marks and aligning timing belt


the marks for th cams are on the tin stuff behind the gears study it for a bit and nyoull see them the mark for the crank pully is on the case onthe bottom of the crank pully just of to one side

Feb 27, 2010 | 1995 Nissan Pathfinder

1 Answer

Timing for tropper 6cly and 4 camshafts and 24 valves model 2000


Timing Belt
Removal
1. Disconnect battery ground cable.
2. Remove air cleaner assembly.
3. Remove radiator upper fan shroud from radiator.
4. Move drive belt tensioner to loose side using wrench
then remove drive belt.
850RW001
Legend
(1) Crankshaft Pulley
(2) Cooling Fan Pulley
(3) Tensioner
(4) Generator
(5) Air Conditioner Compressor
(6) Power Steering Oil Pump
(7) Drive Belt
5. Remove cooling fan assembly four nuts, then the
cooling fan assembly.
6. Remove cooling fan drive pulley assembly.
7. Remove idle pulley assembly.
8. Remove serpentine belt tensioner assembly.
9. Remove power steering pump assembly.
10.Remove crankshaft pulley assembly using
5–8840–0133–0 crankshaft holder, hold crankshaft
pulley remove center bolt, then the pulley.
11. Remove right side timing belt cover then left side
timing belt cover.
12. Remove lower timing belt cover
13. Remove pusher.
CAUTION: The pusher prevents air from entering
the oil chamber. Its rod must always be facing
upward.
014RW011
Legend
(1) Up Side
(2) Down Side
(3) Direction For Installation
(4) Locking Pin
14. Remove timing belt.
CAUTION:
1. Do not bend or twist the belt, otherwise its core
could be damaged. The belt should not be bent at
a radius less than 30 mm.
2. Do not allow oil or other chemical substances to
come in contact with the belt. They will shorten
the life.
3. Do not attempt to pry or stretch the belt with a
screw driver or any other tool during installation.
4. Store timing belt in a cool and dark place. Never
expose the belt direct sunlight or heat.
6A–30 ENGINE MECHANICAL
Installation
NOTE: For correct belt installation, the letter on the belt
must be able to be read as viewed from the front of the
vehicle.
014RY00042
Legend
(1) Crankshaft Timing Pulley
(2) RH Bank Camshaft Drive Gear Pulley
(3) Water Pump Pulley
(4) Idle Pulley
(5) LH Bank Camshaft Drive Gear Pulley
(6) Tension Pulley
014RY00043
Legend
(7) Alignment Mark on Oil Pump.
(8) Alignment Mark on Timing Belt
(9) Alignment Mark (notch) on Crankshaft Timing
Pulley.
(10) Alignment Mark (groove) on Crankshaft Timing
Pulley.
014RW006
Legend
(1) Timing Belt
(2) Engine Rotation Direction
(3) Cylinder Head Side
1. Install timing belt.
1. Align the mark (notch) of crankshaft timing pulley
(2) with mark on oil pump (1).
Align the mark (groove) on the crankshaft timing
pulley (3) with alignment mark (white dots line) on
the timing belt (4).
NOTE: When timing marks are aligned, No.2 piston will
be on Top Dead Center.
014RW003
Legend
(1) Alignment Mark on Oil Pump
(2) Groove on Crankshaft Timing Pulley
(3) Alignment Mark on Crankshaft Timing Pulley
(4) Alignment Mark on Timing Belt
ENGINE MECHANICAL 6A–31
2. Align the alignment mark on the RH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover RH (3).
3. Align the alignment mark (white line) on the timing
belt (1) with alignment mark on the RH bank
camshaft drive gear pulley (2) (on the left side as
viewed from the front of the vehicle) and put the
timing belt on the camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
014RW00004
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover RH.
4. Align the alignment mark on the LH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover LH (3).
5. Align the alignment mark (white line) on the timing
belt (1) with the alignment mark on the LH bank
camshaft drive gear pulley (2).
When aligning the timing marks, use a wrench to
turn the camshaft drive gear pulley, then set the
timing mark between timing belt and camshaft
drive gear pulley and put the timing belt on the
camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
NOTE: It is recommended for easy installation that the
belt be secured with a double clip or equivalent clip after
it is installed the timing belt to each pulley.
014RW00005
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover LH.
6. Install crankshaft pulley temporarily and tighten
center bolt by hand (do not use a wrench).
Turn the crankshaft pulley clockwise to give some
belt slack between the crankshaft timing pulley
and the RH bank camshaft drive gear pulley.
2. Install pusher and tighten bolt to the specified torque.
Torque : 25 N·m (2.5 Kg·m/18 lb ft)
1. Install the pusher while pushing the tension pulley
to the belt.
2. Pull out pin from the pusher.
NOTE: When reusing the pusher, press the pusher with
approximately 100Kg to retract the rod, and insert a pin
(1.4 mm piano wire).
014RW011

Mar 18, 2009 | 2000 Isuzu Trooper

1 Answer

How install timing belt 1993 1.8l eclipse


See Figures 1, 2 and 3
  1. If possible, position the engine so the No. 1 piston is at TDC.
  2. Disconnect the negative battery cable.
  3. Remove the timing belt covers.
  4. Remove the timing (outer) belt tensioner and remove the outer timing belt.
  5. Remove the outer crankshaft sprocket and flange.
  6. Remove the silent shaft (inner) belt tensioner and remove the belt.
0900c152800ad6b2.jpgFig. 1: Silent shaft belt timing marks-1.8L engine 0900c152800ad6b3.jpgFig. 2: Checking the silent shafts for proper positioning 0900c152800ad6b4.jpgFig. 3: Timing belt timing mark alignment-1.8L engineTo install:
  1. Align the timing marks of the silent shaft sprockets and the crankshaft sprocket with the timing marks on the front case. Wrap the timing belt around the sprockets so there is no slack in the upper span of the belt and the timing marks are still aligned.
  2. Install the tensioner pulley and move the pulley by hand so the long side of the belt deflects about 1/4in.
  3. Hold the pulley tightly so the pulley cannot rotate when the bolt is tigthened. Tighten the bolt to 15 ft. lbs. (20 Nm) and recheck the deflection amount.
  4. Install the timing belt tensioner fully toward the water pump and tighten the bolts. Place the upper end of the spring against the water pump body.
  5. Align the timing marks of the camshaft, crankshaft and oil pump sprockets with their corresponding marks on the front case or rear cover.
There is a possibility to align all timing marks and have the oil pump sprocket and silent shaft out of time, causing an engine vibration during operation. If the following step is not followed exactly, there is a 50 percent chance that the silent shaft alignment will be 180 degrees off.
  1. Before installing the timing belt, ensure that the left side (rear) silent shaft (oil pump sprocket) is in the correct position as follows:
    1. Remove the plug from the rear side of the block and insert a tool with shaft diameter of 0.31 in. (8mm) into the hole.
    2. With the timing marks still aligned, the shaft of the tool must be able to go in at least 2 1/2 in. If the tool can only go in about 1 in., the shaft is not in the correct orientation and will cause a vibration during engine operation. Remove the tool from the hole and turn the oil pump sprocket 1 complete revolution. Realign the timing marks and insert the tool. The shaft of the tool must go in at least 2 1/3 in.
    3. Recheck and realign the timing mark.
    4. Leave the tool in place to hold the silent shaft while continuing.
  2. Install the belt to the crankshaft sprocket, oil pump sprocket, then camshaft sprocket, in that order. While doing so, make sure there is no slack between the sprocket except where the tensioner is installed.
  3. Recheck the timing marks' alignment. If all are aligned, loosen the tensioner mounting bolt and allow the tensioner to apply tension to the belt.
  4. Remove the tool that is holding the silent shaft and rotate the crankshaft a distance equal to 2 teeth on the camshaft sprocket. This will allow the tensioner to automatically apply the proper tension on the belt. Do not manually overtigthen the belt or it will howl.
  5. Tigthen the lower mounting bolt first, then the upper spacer bolt.
  6. To verify correct belt tension, check that the deflection at the longest span of the belt is about 1/2in.
  7. Install the timing belt covers and all related items.
  8. Connect the negative battery cable.

Jan 21, 2009 | 1993 Mitsubishi Eclipse

Not finding what you are looking for?
1997 Volkswagen Jetta Logo

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60769 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...