Question about 1989 Nissan Maxima

1 Answer

1989 nissan maxima

Does a nissan maxima have more then 2 bolts holding the thermastat housing in

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

No it only has the two

Posted on Jul 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am trying to change the thermostat in my 1989 nissan maxima. im not sure if i put it in the top or bottom hose. please help. i need to find a diagram but am having trouble locating one.


Follow the upper radiator hose to the engine block. There should be a roundish metal housing at the end of it. Put a bowl underneath to catch any fluid and take off the bolts(try a 10mm socket or wrench) that hold the thermostat housing to the head. Then just pull out the thermostat and scrape off the old gasket. Put the new thermostat on spring-side toward engine, just like the old one. Make sure to use a new gasket! Then push the housing back over it and tighten the bolts. Add any anti-freeze necessary and your done!

Jan 16, 2011 | 1989 Nissan Maxima

1 Answer

How do I locate the thermostat on the Nissan Maxima 1989?


The upper radiator hose connects to the thermostat housing . Loosen clamp and remove hose from housing nipple , there will be two bolts one on either side of the housing remove bolts lift housing and thermostat will be under it ,pay attention to the way it is facing before removing . remove old thermostat clean off old gasket seal install new gasket (it will come with the new thermostat ) install new thermostat face same direction as the old one was. reinstall housing and hose . refill radiator with antifreeze let car run till it warms to normal running temp check for leaks on hose and housing tighten clamp or bolts if needed if no leaks your done. Hope this helps.

Jan 15, 2011 | Nissan Maxima Cars & Trucks

4 Answers

I need to know where the thermostat is located on the engine


follow top radiator hose to engine where hose stops thats where the tstats at.

Sep 03, 2010 | 1997 Cadillac DeVille

1 Answer

Were is the thermastat on a 1996 maxima


Follow the top radiator hose to where it connects to the engine block. There will be a housing with two or three bolts holding it down. Remove the radiator hose from the housing, remove the bolts and lift the housing off. The thermostat will be sitting under the housing.

Jan 22, 2010 | 1996 Nissan Maxima

1 Answer

How to remove a 1989 nissan 300zx starter


Changing StarterIts easy, jack the car up, secure the car with in the up position do not just rely on the jack to hold it up and you will see the starter on the passenger side of the car, its held on with 2 bolts. Disconnect the battery first, then loosen and remove the 2 bolts holding the starter in place. Slide the starter out, disconnect the wires coming from the battery. Reverse the procedure to replace the starter.

Oct 05, 2009 | 1989 Nissan 300ZX

1 Answer

1989 maxima


follow the upper radiator hose to the timing belt end of the engine to locate the thermostate housing

Dec 21, 2008 | 1989 Nissan Maxima

1 Answer

Thermostat install for 1989 Maxima


it goes inside of the housing unit. but when you put the housing unit on, the stem should be pointing to the engine

Dec 02, 2008 | 1989 Nissan Maxima

1 Answer

Need location of thermostat for 1999 nissan maxima gle


thermostat in a 99 maxima is right above the alternator. just look down and you will see a hose clamp and a hose. that's the thermostat housing. you will remove the whole housing (3 bolts),because that's the whole thermostat.

Jul 30, 2008 | 2003 Nissan Maxima

2 Answers

1991 nissan maxima


I just went thru this on mine... it is easiest to get to from the bottom right corner... remove the shields and it's right there... take the lower adjustment bolt out , the upper rear bolt and the upper outer bolt out , drop it down and swap wires and replace . Tip; a shorty phillips screw driver works well to allign the holes on the upper rear bolt. DO NOT tighten any of the bolts untill they are all in.

Jul 21, 2008 | 1991 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...