Question about 2002 Land Rover Freelander

3 Answers

Rover freelander clutch pedal stays on the floor

Posted by on

  • Anonymous Aug 18, 2008

    had to get into gears when warm



3 Answers

I have the same problem. Your clutch booster kit is broken and needs to be replaced. It is that cylindrical hydraulic component next to the engine. Even if just a small part in this thing is jammed you have to replace the whole thing. Well, that's what the guys from land rover told me anyway. Good luck.

Posted on Sep 17, 2008


No clutch cable fitted on these vehicles,hydraulic fault.

Posted on Aug 15, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,027 Answers

Broken clutch cable.

Posted on Jul 15, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Clutch pedal return too high

Freelander 1.8 clutch pedal height is set by the master cyl piston ram.
Circlip has broken or come lose allowing the piston to come out more.
FIX This is a sealed system. Cost from about £45.for system. Can be changed easly at the roadside 30 min no special tools needed

Apr 01, 2014 | 2002 Land Rover Freelander

1 Answer

Freelander Clutch Pedal down to floor

A very common problem this, usually due to the slightly weak clutch slave cylinder mounting plate that has weakened due to a crack and bending. See this video for how to fix it.

Apr 19, 2012 | 2002 Land Rover Freelander

1 Answer

Clutch pedal on the floor ive checked the flid in the master cylinder and it is full is it the clutch tht has gone

pump it rapidly, maybe have to pick it up with your hand, its possible the clutch master is bad, as long as it was working normally before this happened. If it pumps up and feels normal after rapidly pumping I would suspect the clutch master cylinder is bad.

Aug 30, 2011 | 2003 Land Rover Freelander

2 Answers

I have a 2002 freelander TD4 and we think the clutch has gone when u push the clutch pedal down it just stays there and wont come back up does this sound like the clutch has gone?

Sounds like a clutch control problem. Did you check the fluid in the clutch master? If you get a leak and run out of fluid this will also do this. This vehicle uses DOT 4 brake fluid in the master.

Jun 06, 2011 | 2002 Land Rover Freelander

1 Answer

Have to push pedal clear to the floor otherwise the gears are tight to change .Have been told a new m/Cyl we cure this ----do yoiu agree 2004 td4

Yes if you are not loosing the clutch fluid and it is not leaking and the reservoir remains full then most likely you will need to change your master cylinder.

Jan 30, 2011 | 2004 Land Rover FreeLander

1 Answer

Clutch pedal does not need to be lifted far away from floor before engaing, less travel than usual, 2003 TD4 , the pedal is not as firm as usual, softer pedal.....

if its a clutch cable it been adjusted to tightly, common after a new cluth, will start to lift after use but double check the cable is not to tight as it may snap. if its hydrolic then the oil coild be low or air locked.

Jan 13, 2010 | 2003 Land Rover Freelander

1 Answer

Probable clutch needed

If you put your car in 1'st gear, release the clutch pedal and nothing happens, absolutely the clutch is faulty.

Feb 15, 2009 | 2002 Land Rover Freelander

1 Answer

1998 freelander

First Top up the fluid for the hydraulic clutch. This reservoir should be on the fire wall beside the brake master cylinder.

The Clutch slave cylinder is located on the side of the bell housing under the car. You can follow the hose or line from the mater cylinder to find it. There is a bleeder on the end of this cylinder. Open the bleeder at least a few turns and have someone watch the fluid in the master cylinder and just let the fluid run out until you get no air. If it will not self bleed as described above, have someone pump the clutch pedal to the floor and hold it there. Open the bleeder at the slave Cylinder until no more fluid or air comes out and close the bleeder. Tell the person holding the clutch down to slowly release the pedal, or pull it up from the floor. again, slowly. Repeat this process until you have no more air being expelled. Do not let the fluid level of the master cylinder drop below minimum. Note Brake fluid used in this hydraulic system will remove paint. Be careful.

Good Luck

Feb 09, 2009 | 2002 Land Rover Freelander

1 Answer

Hard clutch pedal

You cannot bleed a servo. it runs using the vacuum from either inlet manifold, or a seperate vac pump.Ensure pump is working if fitted (end of camshaft) the pipes to the servo are not leaking by removing the pipe from servo and start veh. If there is good suction then its servo failure. hard pedals can also be caused by pressure plate fatigue in the clutch itself.

Dec 30, 2008 | 2002 Land Rover Freelander

Not finding what you are looking for?
2002 Land Rover Freelander Logo

Related Topics:

592 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

79847 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides