What is the tool called that i need to remove the radio, in order to install an aftermarket deck?

I get this question a lot - Installing aftermarket decks in this car can be a real problem.There are a fairly large number of entertainment options for this car, and the OEM wiring harness used depends on which one you have. In cases where a Bose system is installed, there is no direct connection from the radio to the speakers - just preamp lines to the Bose amplifier at the back of the car, and aftermarket installations require bypassing that amp (which can be a nightmare). To figure out what you have to do, you need the wiring diagrams for your deck and the system you are replacing - try Alldatadiy.com.

It appears to be that the radio clock display has malfunctioned, and is due for a replacement radio, which could be an aftermarket or oem radio, maybe found at a junk yard.

Tools required for oem replacement radio, torx keys set.

Before working on the radio or other electronics, disconnect the battery cables with 8mm wrench.

Replacing the oem radio is much easier, if you obtain oem radio, compared to aftermarket radio, due to being direct fit.

The radio is same for 1995 to 1999 Pontiac Sunfire and the Chevy Cavalier, regardless of sub models, such as SE,GT, VL,VLX,Z24. etc.

Parts needed for the the aftermarket radio install :Stereo assembly, stereo wiring harness adapter, radio antenna adapter, and dash install kit.wiring diagram for the wire colors / functions, along with tools, such as torx key set, screwdrivers,wire crimper, wire stripper, double ended wiring connectors, hair dryer.

The oem stereo removal video is for the 2000 to 2005 Sunfire / Cavalier, but are the same or very similar procedures.

Link to oem stereo removal procedures.
Pontiac Sunfire Radio Repair and Removal 2000 2005


Link to aftermarket stereo install / connect procedures. ( Sunfire Video )
HOW TO INSTALL AFTERMARKET STEREO PONTIAC SUNFIRE

Link to aftermarket stereo install / connect procedures. ( General Video )
How To Install Car Stereo Single Double DIN Car Audio 101


Have a nice day.

Which diagrams do you need?...if it is to install an aftermarket deck, get an adapter so u dont cut into the factory wiring harness..the adapter plugs into the factory plug and allows u to solder the aftermarket radio wires to the other side of it.I have attached a link to where u can get the adapters...unfortunatly this wont allow me to send u my radio schematics that are in PDF format.
Car Stereo Installation Parts for2003 FORD WINDSTAR

you need a new aftermarket radio you blown your sound wires relay inside the deck !!

I can't answer your question, but i can give you a suggestion. What I did, was go to eBay and buy a radio wiring harness for the vehicle I was going too install the radio into (I think this one is for you vehicle eBay auction # 330605601746, I have nothing to do with said auction. You can also try Amazon.com, but eBay for me was cheaper) You hook the radio up to the harness and just plug it into the car's radio plug. Since the car currently has an aftermarket radio installed, they may have cut the cars plug off and installed it directly. You would have to pull the radio out to check first.

Your aftermarket radio should have color-coded wires which identifies power, ground, speakers, etc. most depaetment stores carry a radio harness adapter kit. This will connect to your radio's exact color coded wires, and will plug right in to your factory's wiring plug. And don't forget electrical tape.

You can buy conversion harnesses from anyone that sells radios. It plugs into your factory plug and then you splice the aftermarket stereo wires to it.

1. Disconnect the negative battery cable. Important: When removing a door trim panel or switch plate, disconnect the negative battery terminal. This will eliminate the possibility of shorting out the switch if you use a screwdriver, an awl, or other metal object in order to remove the switch from the harness.
2. Remove the window regulator handle, if equipped.
3. Remove the front door warning reflector.
4. Remove the door panel screw (1) through the hole in the door warning reflector opening.
5. Use a flat bladed tool in order to remove the rear deck release switch bezel.
6. Disconnect the rear deck release switch.
7. Use a flat-bladed tool in order to remove the lower switch bezel trim screw access cover.
8. Remove the lower switch bezel trim screws.
9. Remove the lower switch bezel
10. Use a flat-bladed tool in order to pry the front door switch bezel upward.
11. Disconnect:

1. Gently disengage the front door trim retaining clips and remove the door trim panel from the door.

Installation Procedure

1. Install the front door trim panel to the door. Ensure that the retainers are locked into place.
2. Connect the rear deck release connector.
3. Install the rear deck release switch bezel. Press the bezel firmly into place.
4. Install the window regulator handle to the door.
5. Connect:

• lock switch connector, if equipped.
• Power window switch connector, if equipped.
• Power mirror switch connector, if equipped.

1. Install the front door switch bezel assembly to the front door trim panel.
2. Install the lower switch bezel trim panel. Notice: Refer to Fastener Notice in Service Precautions.
3. Install the lower switch bezel trim screws.
4. Install the lower switch bezel trim screw access cover.
5. Install the door trim panel screw (1) through the hole in the front door warning reflector.
6. Install the front door warning reflector.
7. Connect the negative battery cable.

is this a post raido or flat face? flat faces will have din pins 2 hole each side of raido have to get a tool to remove --also get wire adp. frm parts store will b -easy that way

Ebay has the tool for removal cost $1 plus shipping. this tool is for the 2 holes on left and right side of radio face fit tool in then push alittle out worad and pull. Follow aftermarket instructon on install.