Question about 1994 GMC Jimmy

1 Answer

1994 gmc jimmy steering wheel removal

Hi firsttime here trying to replace a ignition to a '94 jimmy and was wandering how to remove S.Wheel so that i could get to the next step

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 589 Answers

Gently pop off the horn cap / cover.

There will be a short wire attached, so be careful not to pull it too hard.

You will see the wire going into the metal frame of the steering wheel.

The wire will go into a "sleeve". Push the sleeve in, and turn slightly counter-clockwise to unlock the connector. The horn will beep a few times as you pull the wire out, just to warn you :)

You will now need a steering wheel puller. These can be bought for about $10 at any auto parts store.

Once the wheel itself is off, you will see a black plastic disk. remove it. Now you will see a metal disk with notches in it (this is what locks the steering wheel when you turn the key off). You may want to get someone for assistance for this one, as there is a pretty stiff spring behind the disc, so use caution. You will need to push the disc towards the dash and remove the retainer clip.

Once that is off, you will see the white turn signal switch. Remove the hazard switch button first, then the turn signal lever retaing screw (be careful if it has cruise control, as the wires are thin and delicate), then remove the 3 phillips head screws holding the actual switch on. Let the switch hang out of the way.

Now, you'll see the lock cylinder retaining screw. This is where you may have a problem if you don't have a key.

After removing the screw, you MUST turn the ignition switch to the "run" position and pull out the assembly.


Posted on Jun 19, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key gets stuck in ignition of my 1997 GMC Jimmy can't remove until I hear a click. It does this once in awhile.It sounds like a timer has it locked,when I hear the click only then I can remove the the


The steering wheel lock pin is probably not falling into place. Try some lock lubricant and jiggle the wheel back and forth a little bit. If that does not do it, you will have to take out the lock tumbler and free-up / lubricate the steering column lock pin mechanism.

Jan 15, 2015 | 1997 GMC Jimmy

1 Answer

How do i remove an ignition in a gmc jimmy 2000 without a key?


Hello, Dan. First, disconnect the negative (-)/ground on the battery Dan are you mechanically inclined. If not then don't attempted this job.

You will need to remove all the plastic covers on the steering column. Remove the horn ring.--two screws under the steering wheel. Remove the horn ring and disconnect the horn plug. Remove the steering wheel nut. Use a steering wheel puller to remove the steering wheel.

Remove the turn signal switch that fit around the upper part of the steering column. Then remove the some of the parts that are associated with the steering wheel and/or column.

Now, look at the ignition switch flange, it a big chunk of aluminum. Now look for a large aluminum dowel pin 5/8" in diameter that is driven into the chuck of aluminum but it is parallel to the steering column.

This aluminum dowel pin will have to be drill out before you can get ignition housing off, If there is adjustable steering column lever, remove this also.

Now, once the dowel pin has been removed, looking for a **** in the ignition housing. Take chisel and insert into this ****, drive the chisel into the **** until the ignition housing is loose to be remove by sliding it up over the steering column.

If you buy a new ignition switch, on purchase the switch with keys. Don't buy the hole new ignition housing.. If you do it will get expensive.

In the ignition (old) housing drive out the ignition switch pins that keeps the ignition switch in the housing. Install the new ignition switch re-insert the ignition switch hold pins.

I am fairly sure that Carquest/ NAPA some other larger auto parts will have ignition housing bolt. If they try to sell you a replacement aluminum dowel pin don't buy it. It is almost impossible to install the aluminum dowel pin without the proper tools, so use a bolt to squeeze ignition housing together.

Before putting everything back together. Now, check the new ignition switch to make sure it works. I wish you lot of luck. GB...stewbison

Sep 27, 2011 | 2000 GMC Jimmy

1 Answer

Cant figure out how to remove the steering wheel and air bag in i


disconnect negitive battery cable. Remove screws holding air bag to steer wheel. Disconect wires to air bag being. I must stop now. Playing with air bags can result in injury or death. You should have a shop do that for you. Sorry for not helping.

Apr 26, 2009 | 1997 GMC Jimmy

1 Answer

Remove steering wheel on 95 gmc jimmy


u will need a steering wheel puller,u will have to disharm and take airbag off if equip.,i would suggest to get manual it explains step by step procedure!

Apr 24, 2009 | GMC Jimmy Cars & Trucks

1 Answer

I want the step by step instructions to replace the ignition switch.


Hi. I've put together a guide that will help you with the replacement of this ignition switch.


Step1 Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing or unclipping them. Step2 Remove the steering wheelmag-glass_10x10.gif by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft. Step3 Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheel and disconnect the wiring. Slide the spacer sleeve off of the steering column. Step4 Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out. Step5 Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder. Step6 Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.You have just completed the task.Good job:)


Please rate and god bless.




Mar 27, 2009 | 1994 GMC Safari

2 Answers

Key stuck in the ignition of 1998 GMC Jimmy


sounds like your shift lever for trans isnt making a tight connection when you put it in park....try shifting it in and out of park several times while trying to remove key......my lincoln does that occasionally and when i take it out of park and then back in it works......just a thought

Jan 19, 2009 | 1998 GMC Jimmy

1 Answer

Ignition switch installstion 1991 gmc jimmy


remove steer wheel with puller. u will see black cover remove 3 tork screws.remove. next u will need a special tool push dowd on plate . remove clip in center. lift turn arm . remove bolt for lock cly. turn key lock will slide out

Dec 11, 2008 | 1991 GMC S-15 Jimmy

2 Answers

Need directions replacing ignition switch under dash in a 1993 GMC Jimmy


remove the stearing wheel, get a spring compressor made for steering coloums (they sell them at pepboys for$10)  remove the lock, then the blinker assambly by 3 screws and then one on the switch. if its in the switch its self and not the lock cyclinder, drop the steering coloum down and it on top of the colum with a rod going to it

Jul 24, 2008 | 1987 GMC S-15 Pickup

Not finding what you are looking for?
1994 GMC Jimmy Logo

487 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...