Question about 1994 GMC Suburban

1 Answer

1994 GMC Suburban front hub / bearing removal

How do you removal the front bearing / hub assembly from the brake rotor on a GMC Suburan 4x4 2500 (1994)

Posted by on

  • 4 more comments 
  • Anonymous Mar 14, 2014

    Hi i would like to no when i hit my brakes it feel like my brakes is rubbing agaist some metals i change ny hub bearing my rotors and brakes and also my traction light wont go off and what is hwd

  • Anonymous Mar 14, 2014

    Hi i would like to no when i hit my brakes it feel like my brakes is rubbing agaist some metals i change ny hub bearing my rotors and brakes and also my traction light wont go off and what is hwd

  • Anonymous Mar 16, 2014

    remove bearing and hub hyndai elantra 2000 front

  • Anonymous Mar 20, 2014

    Can I do this myself

  • Anonymous Mar 23, 2014

    front hub bearing ison bad chape need to change don't not how

  • Anonymous Mar 23, 2014

    dont know how bearing go

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 702 Answers

Knock the wheel studs through the assy.

Posted on Jun 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change the front wheel bearrings on a 1999 sonoma 2 wheel drive?


The bearing is in the hub.. Here are some instructions for that:
  • The wheel bearing is installed in the wheel hub assembly and is serviced by replacement only.

  • You may need Torx sockets to remove the bearing assembly bolts.


  • Raise and support the front of the vehicle safely using jackstands.

    Remove the tire and wheel assembly.

  • At the wheel hub, remove the cotter pin and retainer, then loosen and remove the castle nut and the thrust washer. In order to hold the hub from turning when loosening the nut, insert a drift through the caliper and into the rotor vanes. Remove the brake caliper and support it aside using wire or a coat hanger. Make sure the brake line is not stretched or damaged.

  • Remove the brake rotor from the wheel hub.

  • Remove the bolts retaining the hub/bearing assembly to the knuckle, then carefully pull the assembly from the splined end of the halfshaft. If available, use J-28733-A or B, or an equivalent spindle remover to prevent damage to the shaft or hub/bearing assembly.


  • Remove the cotter pin from the drive axle end nut and retainer


    Remove the retainer for access to the end nut


    Loosen the drive axle nut-here the caliper is installed so a drift could be inserted to keep the disc from spinning



  • Read more: I want to replace my S10 front wheel bearing. My manual ... - JustAnswer http://www.justanswer.com/chevy/0jwks-want-replace-s10-front-wheel-bearing-manual.html#ixzz1hl5SCxBf

    Dec 26, 2011 | 1999 GMC Sonoma

    1 Answer

    Left front wheel bearing replacement diagram


    Removal & Installation Front To Remove:
    The front wheel bearings are not serviced separately. If the front wheel bearings are defective, the hub and bearing assembly must be replaced.
    1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
    2. Lubricate the threads on the halfshaft with clean engine oil.
    3. Remove or disconnect the following:
      • Front wheels
      • Halfshaft hub nut
      • Caliper from the steering knuckle WARNING
        DO NOT allow the brake hose to support the weight of the caliper.
      • Brake rotor
      • Anti-lock Brake System (ABS) sensor from the backing plate
      • Hub and bearing assembly from the backing plate
      • Hub and bearing assembly from the halfshaft
      • Hub and bearing assembly
    To Install:
    Exploded view of the front hub mounting and related components 7922xg36.gif

    1. Install or connect the following:
      • Hub and bearing assembly onto the halfshaft
      • Hub and bearing assembly to the backing plate. Torque the 3 bolts alternately and evenly to 70 ft. lbs. (95 Nm).
      • ABS sensor
      • Brake rotor
      • Caliper on the steering knuckle.
      • Halfshaft nut. Torque it to 118 ft. lbs. (160 Nm).
      • Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

    Oct 18, 2010 | 2001 Oldsmobile Aurora

    1 Answer

    Need to remove the front hub to replace the brake rotor on 3/4 to 4wd


    bolts are behind the steering knuckle to remove the bearing and hub assy.

    Oct 13, 2010 | 1996 GMC Suburban

    1 Answer

    How do you remove the Hub and Rotor on a 97' F250 with Auto 4 wheel drive? I can not get the rotor to come off. I know that the hub must come with it. However, I am not sure what I have not removed in...


    Section 05-03C: Wheel Hubs and Bearings, Front Wheels, 4-Wheel Drive 1997 F-250/350/Super Duty Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000 Locking Hubs, Manual

    e9801b.gif


    Item Part Number Description 1 3A329 Halfshaft 2 3C132 Rolling Diaphragm Seal (Axle) 3 3299 Integral Spacer Needle Bearing Seal 4 3123 Bearing, Caged Needle 5 3105 Front Wheel Spindle 6 1190 Wheel Hub Grease Seal 7 4221 Inner Wheel Bearing (with Bearing Cup 4222) 8 1102 Front Disc Brake Hub and Rotor 9 4221 Outer Wheel Bearing (with Bearing Cup 4222) 10 - Pin (Part of 1195) 11 1195 Inner Lock Nut 12 1198 Lockwasher 13 1197 Outer Lock Nut 14 - Steel Thrust Washer
    (Part of 3B458) 15 - Plastic Thrust Washer
    (Part of 3B458) 16 - Splined Thrust Washer
    (Part of 3B458) 17 3B457 Snap Ring 18 1K105 Hub Body 19 - Lock Ring (Part of 1K106) 20 1K104 Cap 21 1K104 Capscrew A - While Rotating Front Disc Brake Hub and Rotor, Tighten Inner Lock Nut to 68 Nm (50 Lb-Ft) to Seat Bearings. Back Nut Off 90 Degrees (1/4 Turn). B - Tighten to 217-278 Nm (160-205 Lb-Ft) C - Tighten to 4-6 Nm
    (35-53 Lb-In) Removal
    1. Separate cap assembly from hub body by removing the three Torx® head capscrews.


      de0460a.gif



      de0285a.gif

    1. Remove the lock ring seated in the groove of the front disc brake hub and rotor (1102).


      f4658c.gif

    1. Remove the hub body assembly from the front disc brake hub and rotor. If the body is difficult to remove, install two capscrews and pull the body assembly out of the front disc brake hub and rotor.


      f4659d.gif

    Installation
    1. NOTE: Do not pack the hublock body assembly or cap with grease. Excessive grease can cause excessive dialing effort and hub failure.

      Follow removal procedure in reverse order.
    1. Tighten three Torx® head capscrews to 4-6 Nm (35-53 lb-in).

    Oct 04, 2010 | 1997 Ford F250 SuperCab

    1 Answer

    I have a chrysler lhs 1994 with a bad front wheel bearing and i need instruction on repair


    These are the steps you need to follow for this procedure if you have the proper tools.
    1. Remove front caliper assembly and rotor from the steering knuckle as outlined under "Caliper, Replace" in the "Disc Brake" unit repair section.
    2. Remove hub and bearing to stub axle retaining nut.
    3. Disconnect hub bolts then remove hub and bearing assembly from steering knuckle by sliding it straight off end of stub axle. If metal seal on hub and bearing assembly is seized to steering knuckle and becomes dislodged on hub and bearing assembly during removal, or when removing hub and bearing, the finger disc on hub becomes damaged, hub and bearing assembly must be replaced.
    4. If hub and bearing will not slide out of knuckle, insert a prybar between hub and steering knuckle and gently pry hub and bearing from knuckle.
    5. Tighten stub shaft nut, lower vehicle and with brakes applied, torque stub shaft nut to 70 - 90 ft. lbs.

    Aug 27, 2010 | 1994 Chrysler LHS

    1 Answer

    REMOVAL OF FRONT WHEEL BEARINGS


    Front (4 Wheel Drive) To Remove:
    1. Raise and support the vehicle
    2. Remove or disconnect the following:
      • Tire and wheel assembly
      • Rotor (See: Disc Brake Rotor)
      • Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle
      • Electrical connection for the wheel speed sensor
      • Front drive halfshaft assembly (See: Halfshaft)
      • Hub and bearing assembly mounting bolts 4WD front hub 9308kg35.gif

      • Hub and bearing assembly
    To Install:
    1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly
    2. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent
    3. Install or connect the following:
      • Hub and bearing assembly
      • Hub and bearing assembly mounting bolts and tighten the hub to knuckle bolts; Torque to: 133 ft. lbs. (180 Nm)
      • Front drive halfshaft assembly (See: Halfshaft)
      • Electrical connection for the wheel speed sensor
      • Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle and tighten the bolt; Torque to: 106 inch. lbs. (12 Nm)
      • Rotor (See: Disc Brake Rotor
      • Tire and wheel assembly
      Wheel lug nut tightening sequence gm_trk_sub15_wheel_lug_nut_tight_seq.gif

    4. Torque the lug nuts to specification
    5. Test drive the vehicle to confirm the repairs
    prev.gif next.gif

    Aug 03, 2010 | 2001 Chevrolet Silverado 1500

    1 Answer

    How do u replace a front wheel bearing on a 2005 gmc envoy 4x4 and dose anybody have diagrams to follow how to


    Remove center hub cap. Remove large nut behind hub cap.Lift wheel assembly off ground. Remove wheel. Remove brake calipher assembly by taking out larger bolts from back of calipher. Remove brake rotor. Pull axle toward middle of vehicle, you may have to tap axle end with small hammer being careful not to damage threads on end of axle. Remove three bolts from back, bearing housing should come out to the front.

    Jul 12, 2010 | 2005 GMC Envoy

    1 Answer

    How do I change front hub and bearing assembly on 2004 Explorer


    Front hub bearing, remove tire, remove caliper and caliper holding bracket, you do not have to remove brake caliper from brake hose, just set it aside, if 4X4 remove front axle nut that goes through center of rotor, also remove brake rotor, disconnect elec, A.B.S connector, remove three bolts on back side of hub bearing, remove hub bearing, some times you will need to knock hub bearing out with a hammer.Reverse to install new hub bearing.

    Jul 09, 2010 | 2004 Ford Explorer

    1 Answer

    Replace front hub assembly.


    Replacing the front wheel bearing/hubs can be a big job for the inexperianced. Briefly...
    Remove tire/wheel
    Remove brake caliper assembly, do not remove brake line.
    Remove caliper bracket.
    Remove brake rotor.
    Unplug ABS sensor.
    Remove the large axle nut.
    Press axle out of bearing (may need special tool)
    Remove the 3 bearing bolts and remove bearing.

    May 19, 2010 | 2003 Chevrolet Impala

    1 Answer

    How to replace 99 gmc 3/4 tom brake rotors


    Removal & Installation
    1. Remove 2/3of the brake fluid from the master cylinder.
    2. Raise and support the vehicle.
    3. Remove the tire and wheel assembly.
    4. Remove the front wheel hub extension (dual wheel vehicles only).
      • Insert a drift or large screwdriver through the brake caliper into one of the brake rotor vanes in order to prevent the rotor from turning.
      • Mark the relationship of the front wheel hub extension to the hub
      • Remove the front wheel hub extension bolts
      • Remove the front wheel hub extension from the vehicle. It may be necessary to tap around the perimeter of the hub extension with a rubber mallet to loosen it from the hub
    5. Mark the relationship of the rotor to the hub.
    6. Remove the caliper and mounting bracket as an assembly.
    7. Hang the caliper and the mounting bracket assembly from the suspension using mechanics wire.
    8. Remove the rotor.
    9. If the rotor is difficult to remove due to corrosion in the hub area use the following procedure to remove the rotor (25 series only).
      • Clean all the surface areas and the threaded holes of contamination
      • Generously apply penetrating oil or the equivalent to the hub/rotor area
      • Insert (2) M10 x 1.5 bolts (jack screws) into the threaded holes of the rotor
      • Tighten both bolts evenly to force the rotor from the hub.
    c3692a2.gif
    To install:
    1. Clean all rust and contaminants from the both side of the rotor and the hub flange.
      NOTE If the rotor was removed using the jack screw method you must ensure that the hub flange is free of nicks or marks caused by this procedure. Remove all raised nicks or marks before installing the rotor.

    2. Install the rotor.
    3. Install the caliper and the mounting bracket as an assembly.
    4. Install the tire and wheel assembly.
    5. Remove the safety stands.
    6. Lower the vehicle.

    Oct 25, 2009 | 1999 GMC Sierra

    Not finding what you are looking for?
    1994 GMC Suburban Logo

    Related Topics:

    854 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top GMC Experts

    yadayada
    yadayada

    Level 3 Expert

    61037 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a GMC Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...