Question about 1993 Ford Econoline

1 Answer

How to remove blower motor switch - 1993 Ford Econoline

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Gently pry the cover plate from around the radio/switches it will unsnap. remove hexnuts from fan switch assembly. remove hexnut from back of switch to remove from assembly then unplug electrical connections.

Posted on Nov 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How h on I remove the blower switch on a 2012 ford e-150 van


Are you wanting to remove the switch that selects the blower motor speed, or the blower motor resistor that controls the blower motor speed? Also, are you asking for the front blower motor or for an auxiliary (rear) blower motor?

Dec 23, 2017 | Ford E-150 Cars & Trucks

1 Answer

Heater switch replacment


Hello! it's my job to make things as easy for the customer as possible...Therefore I must ask why you want to replace the heater switch? Is it because you have lost one or two of the switch speeds? Your vehicle is noted for loss of the Blower Motor Resistor...
Changing the Heater switch means removal of the Climate Control Assembly which is not the easiest of jobs...I've included the process...But are you sure the blower resistor is OK? If you have lost 1,2, or all blower motor speeds it's more than likely the Resistor pack. And a lot easier to change...
Guru...saailer


Remove climate control:





12_26_2011_2_15_09_am.gif
  1. Remove the instrument cluster finish panel...
  1. Remove the 3 climate control assembly screws...
  1. Disconnect the climate control assembly vacuum connector...
  1. Disconnect the 5 climate control assembly electrical connectors...
  1. Remove the climate control assembly..
Removal of blower motor Switch:
  1. Remove the climate control assembly.
  1. Remove the blower motor switch knob.
  1. Remove the blower motor switch.
    1. Remove the screw.
    1. Remove the blower motor switch.

Removal of blower motor Resistor:


12_26_2011_2_22_49_am.gif
Blower Resistor is under the battery tray...

MOTORCRAFT Part # YH1698 ...cost $25

12_26_2011_2_28_50_am.jpg

Guru...saailer

I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

Dec 22, 2011 | 2007 Ford Econoline

1 Answer

99 olds heater heats,but doesnt come on


CHECK HEATER AND AC IGNITION 10 AMP FUSE UNDER HOOD JUNCTION BOX.IF ALL IS GOOD CHECK BLOWER MOTOR FUSE AND RELAY.IF ALL LOOKS GOOD. TURN ON CONTROL SWITCH TO CHECK TO SEE IF POWER GOING TO BLOWER MOTOR IF YES BLOWER MOTOR BAD.IF NO POWER GOING TO BLOWER MOTOR FUSE AND RELAY GOOD.YOU HAVE BROKE WIRE BETWEEN SWITCH AND BLOWER MOTOR OR CONTROL SWITCH FAULTY. TO GET TO BLOWER MOTOR ITS LOCATED UNDER THE DASH ON PASSENGER BEHIND GLOVE COMPARTMONT YOU DONT HAVE TO REMOVE GLOVE BOX ITS JUST BELOW IT FAR BACK.YOU NEED TURN OFF RADIO FIRST THEN DISCONNECT NEGATIVE BATTERY CABLE WAIT 20 MINUTES THIS DISABLE AIRBAGS AND THE BCM.REMOVE BLOWER MOTOR HOTWIRE IT TO SEE IF ITS WORKS. IF NO BLOWER MOTOR NO GOOD.IF BLOWER MOTOR GOOD THE AC AND HTR CONTROL SWITCH IS BAD DEALERSHIP FIX.

Dec 30, 2010 | 1999 Oldsmobile Alero

1 Answer

My 1988 Ford Tempo's heater fan is not working. I can feel heat at the windshield vents,but the fan wont come on. I have jumped the fan speed switch with a paper clip--and blew a fuse--and checked the...


your circuit is simple--I will paste it below. suspect the blower has shorted and caused the switch to burn up. remove the blower and hotwire it to the battery to see if it works. If not, replace the blower. Then run continuity tests on the swoitch and replace switch if bad. If you have questions, please let me know. Here is procedure for taking blower out:


REMOVAL & INSTALLATION With Air Conditioning

  1. Disconnect the negative battery cable.
  2. Remove the glove compartment door and glove compartment by removing the retaining screws and bolts. Push the sides of the glove box in to free the drawer from dash panel.
  3. Loosen the instrument panel at the lower right hand of the glove compartment opening. This is on it necessary if the panel is in the way of the motor housing.
  4. Remove the retaining screws securing the ducting around the blower motor.
  5. Remove the clip securing the blower motor fan blade to the motor arm. Remove the fan blade from the motor.
  6. Remove the blower motor mounting plate from the evaporator case by unscrewing the retaining screws.
  7. Rotate the motor until the mounting plate clears the edge of the glove compartment opening and remove the motor.
  8. Remove the wire harness from the rear of the motor.
  9. Inspect the fan blade for broken edges or cracks. Replace if needed.

To install:
  1. Connect the wire harness to the rear of the blower motor.
  2. Install the motor into the case and secure with the retaining screws.
  3. Position and fasten the fan blade to the blower motor arm. Secure with the clip.
  4. Secure the blower motor outer housing to the duct assembly with the retaining screws.
  5. Install the instrument panel at the lower right hand side if removed earlier.
  6. Install the glove compartment door and glove compartment.
  7. Connect the negative battery cable.
  8. Run blower motors to make the motor works correctly.
Without Air Conditioning
  1. Disconnect the negative battery cable.
  2. Remove the right ventilator assembly.
  3. Remove the hub clamp spring from the blower wheel hub. Pull the blower wheel from the blower motor shaft.
  4. Remove the blower motor flange attaching screws located inside the blower housing.
  5. Pull the blower motor out from the blower housing (heater case) and disconnect the blower motor wires from the motor.

To install:
  1. Connect the wires to the blower motor and position the motor in the blower housing.
  2. Install the blower motor attaching screws.
  3. Position the blower wheel on the motor shaft and install the hub clamp spring.
  4. Install the air inlet duct assembly and the right ventilator assembly.
  5. Connect negative battery cab
  6. Check the system for proper operation.

36d4b25.gif

Oct 21, 2010 | 1988 Ford Tempo

1 Answer

How to replace a blower motor in a 1996 ford thunderbird lx


Removal
  1. Remove the glove compartment liner to gain access to the heater blower motor and blower motor wheel assembly mounting screws.
  1. Use a small screwdriver to remove clip retaining hydraulic damper strut.
  1. Remove four screws and remove the heater blower motor assembly and blower motor wheel assembly from the heater blower motor housing.
Installation
  1. Using a new seal, position the heater blower motor and blower motor wheel assembly to the heater blower motor housing with the flat side of the flange near the heater blower motor switch resistor (18591). Install the four retaining screws.
  1. Tape the heater blower motor power lead to the air inlet duct to keep the wire away from the blower outlet during installation.
  1. Install the heater blower motor and blower motor wheel assembly in the vehicle.
  1. Install the glove compartment liner.

Oct 07, 2010 | 1996 Ford Thunderbird LX

1 Answer

Fuse diagram for a 98' E-150 van specifically for heater fan


owner manual will tell you fuse layout. If you have only high speed, you have a bad resister. 4 wires.

Resistor —Heater Blower Motor Switch Removal
  1. Remove the battery (10655) ; refer to Section 414-01 .
  1. Remove the battery tray.
    1. Remove the screws.
    1. Remove the battery tray.
  1. Disconnect the heater blower motor switch resistor connector.
  1. Remove the heater blower motor switch resistor (18591).
    1. Remove the two screws.
    1. Remove the heater blower motor switch resistor.
---------------------------------

0f120f5.gif

Feb 26, 2010 | 1998 Ford Econoline

1 Answer

Blower motor doesn't blow anymore, This blows


If it blows only on high speed, it is the resister.
If it does not work at all, check fuses first. See owner manual for location.
Then check blower motor by jumping 12 volts from battery to blower motor. Make sure ground is jumped too.

If it works now, it's the control panel. If not, it is the motor.

Blower Motor —Front Removal and Installation
  1. Prepare the vehicle for blower motor (19805) removal.
    1. Disconnect the battery ground cable (14301). For additional information, refer to Section 414-01 .
    1. Remove the air cleaner assembly. For additional information, refer to Section 303-12 .
  1. Detach the speed control servo.
    1. Disconnect the electrical connector.
    1. Remove the bolt.
    1. Position the speed control servo aside.
  1. Position the coolant expansion tank/windshield washer reservoir aside.
    1. Remove the screws and the nuts.
    1. Position the coolant expansion tank/windshield washer reservoir aside.
  1. Remove the blower motor.
    1. Disconnect the vent hose.
    1. Disconnect the electrical connector.
    1. Remove the four screws.
    1. Remove the blower motor.
f285484.gif
Also,

Heater Blower Motor Switch Resistor(s)
The front heater blower motor switch resistor has the following features:
  • The assembly is located in the engine compartment on the evaporator housing (19850) next to the blower motor assembly (19805).
  • Three resistor elements are mounted on the resistor board to provide four blower motor speeds.
  • Depending on the heater blower motor switch position, series resistance is added or bypassed in the A/C blower motor circuit to decrease or increase A/C blower motor speed.
  • An overheating device (thermal limiter) will open the resistor coil circuit when the temperature reaches 121°C (250°F), interrupting the blower motor operation in all speeds except high.
  • The thermal limiter cannot be reset and is not serviceable.

Aug 10, 2009 | 2001 Ford Explorer Sport

1 Answer

I have a 2000 ford E350 van with front and rear air. the front blower motor runs at low speed, The front blower still runs on low even when the knob is set on medium or high. I do not know where the...


it's either the blower motor switch or blower motor resister. Resistor ?Heater Blower Motor Switch Removal Remove the battery (10655) ; refer to Section 414-01 . Remove the battery tray. Remove the screws. Remove the battery tray. Disconnect the heater blower motor switch resistor connector. Remove the heater blower motor switch resistor (18591). Remove the two screws. Remove the heater blower motor switch resistor. ----------------------------------- Switches Removal Disconnect the battery ground cable. Remove the center trim panel; refer to Section 501-12 . Remove the control assembly. Remove the screws. Remove the control assembly. Remove the A/C-heater function selector switch knob. Disconnect the vacuum harness connector. Disconnect the A/C-heater function selector switch connector. Remove the A/C-heater function selector switch. Remove the screw. Remove the A/C-heater function selector switch. Remove the temperature control switch knob. Disconnect the temperature control switch connector. Remove the temperature control switch. Remove the screw. Remove the temperature control switch. Remove the heater blower motor switch knob. Disconnect the heater blower motor switch connector. Remove the heater blower motor switch (18578). Remove the screw. Remove the heater blower motor switch. ----------------------------

Mar 31, 2009 | 2007 Ford E-350 Super Duty Length XLT

1 Answer

Blower problem


The blower motor resistor:
  • is located on the heater core and evaporator core housing near the blower motor.
  • has three resistor elements mounted on the resistor board to provide four blower motor speeds.
  • depending on the blower motor switch position, series resistance is added or bypassed in the blower motor circuit to decrease or increase blower motor speed.
  • has an overheating device (thermal limiter) that will open the resistor coil when the temperature reaches approximately 184°C (363°F) , interrupting the blower motor operation in all speeds except high.
  • is serviced as an assembly. The thermal limiter cannot be reset and is not serviceable.
REMOVAL
  1. Lower the glove compartment.
  2. Remove the screws and position aside the 4x4 control module.
  3. Remove the blower motor resistor.
4 Disconnect the electrical connector. 5 Remove the screws and the blower motor resistor. INSTALLATION
  1. To install, reverse the removal procedure.

Nov 06, 2008 | 1995 Ford Explorer

Not finding what you are looking for?
1993 Ford Econoline Logo

Related Topics:

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85108 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...