Question about 1996 Oldsmobile Bravada

1 Answer

Engine stalling while stopping

I have recieved 2 codes and do not know how they can cause engine to stall while stopping. The codes are: p0700 and p1192.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 87 Answers

Torque converter lockup stuck time for a new converter transmission rebuild

Posted on Jun 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an 05 Suzuki Forenza that has a flashing check engine light. This started on Tuesday. Had the codes looked up. Car is driving shaky and dash lights are blinking. Any ideas?


fix the anti freeze leak --before you blow a head gasket

what your codes mean

Check Engine Light On, P0300 Random Misfire Code. A random misfire means your engine is misfiring, but that the problem is not isolated to one or two cylinders. It is jumping around in a random way from one cylinder to another. A random misfire code usually means the air/fuel mixture is running lean.

What the P0700 code means. P0700 is set when the PCM detects a malfunction in the transmission control system. This malfunction causes the vehicle to set a Check Engine Light and trigger a failsafe mode. Once the failsafe mode is set it will remain until the fault is repaired or normal operation is detected.

PO133 Oxygen Sensor Circuit Slow Response (Bank1, Sensor1)

Nov 25, 2016 | Suzuki Cars & Trucks

1 Answer

My jeep begins to shake and slow down once I hit 35mph. It will eventually stop, and after sitting with it off for about 30-45min it'll accelerate again but only up to 30mph. It smells electrical, but I...


wow, no year , no jeep model or even an engine size stated.
cause is first. price is last. always.
stalls.
there are 50 ways to stall. (i can list them but is just a waste)
if you dont know how to do the tests, that leaves only 2 choices.
1: tow it in for diagnosis.
2: or get a house call,$$$$$$$$$$$$$$$$$$$$$$$

since this forum can't do 1 or 2, that leaves , advice.
A: ever do a 60k tune up on this, engine in the last decade?
B: when running does the CEL lamp glow? , not stalled.
C: when it does stall and engine hits zero RPM is the CEL glowing (it must)
D: when it stalls are all cluster lights on and bright , per normal?
E: when it stalls does the dash voltmeter stay above 12v? or near.
if no dash meter , then connect a meter to the CIG lighter port
and watch voltage there at the stall.

CEL means check engine light.

that stall is from gross misfire. of the engine.
my guess.
bad spark
bad fueling
there are tests for each but im not typing 10 pages to say.

Aug 16, 2013 | Jeep Cars & Trucks

1 Answer

2000 sebring 2.5 stalls out and overheats


Have the fault codes read. Replace faulty items. Use only genuine items as non-genuine replacement are not always compatible with the OEM fitted CPU units. The engine light is telling you that the cpu has found a fault ( probably overheating) from a radiator fan not coming on. The stalling could be the cpu going into protect mode and stopping the engine

Jun 11, 2013 | Cars & Trucks

1 Answer

PO744 code 2001 infiniti qx4 how do i fix


CODE PO744 AUTOMATIC TRANSMISSION TORQUE CONVERTER CLUTCH SOLENOID VALVE FAULT. POSSIBLE CAUSE FAULTY TCC SOLENOID.CHECK TCC SOLENOID WIRING FOR DAMAGE.OR YOU COULD HAVE FAULTY TCM OR ECM. IF THE TCC SOLENOID IS FAULTY YOUR ENGINE WILL STALL OUT AT A RED LIGHT OR STOP SIGN.YOUR ENGINE WILL STALL OUT AT EVERY STOP THAT WOULD BE SIGN FAULTY TCC SOLENOID.IF ENGINE DONT STALL OUT THE TCC SOLENOID COULD COULD BE STUCK OPEN, IF YOUR TORQUE CONVERTER FAULTY IT WILL CAUSE PREMATURE LOCKUP STALLING OUT THE ENGINE.

Nov 01, 2011 | 2007 Infiniti QX4

2 Answers

My 2005 Mitsubishi oz rally feels like it wants to stall while I'm driving. The service engine light has not come on. It has only stalled once while at a complete stop.


I checked for Technical Service Bulletins (TSB's) and Recalls for your vehicle, but I found no TSB's related to your problem and the only Recall that has been issued for your vehicle is for a problem with the headlamps.

I can only offer 2 pieces of advice at this point:
1. If it feels like the engine RPM is not correct, i.e too slow or erratic when you are coming to a stop, I would be taking a hard look at the Idle Air Control Solenoid (IAC) These can fail and never set a code.

2. You may want to have your engine computer scanned with a scanner that can check "Vehicle Specific Codes" There may be codes or pending codes stored in your engine control module that have not yet or cannot turn on the Check Engine light. Some of these types of codes are vehicle specific and most generic OBD code readers can't even see them. I have many times found several codes stored without the Check Engine light being on.

Post a comment to let me know how this turns out, or if you have any related questions.

Mar 09, 2011 | 2005 Mitsubishi Lancer

1 Answer

Tranny causes engine to stall when tranny warms up


if it feels like your driving a standard transmission ,and "you came to a stop light without pushing clutch in"
that will be the torque convertor lock up,

Jan 12, 2010 | 1995 Pontiac Sunfire

1 Answer

2000 kia sephia constant engine stalling!!!


try this procedure and let me know if it cures the problem.

Here is the common cause of surges, stalls at stops, slow idle speed, erratic idle speed, rough idle and engine hesitation (and other problems), it is in most cases the idle speed control air-bypass valve and or throttle valve and upper intake, these area's get full of gunk and combustion residue over the miles and cause idle issues (stalls, low idle) like yours, Get a can of intake cleaner from any local parts store, not carb spray, intake cleaner, it is made by a company called CRC, remove the air intake hose to the engine, hold the idle high so the engine won't stall, then spray the can of cleaner into the intake while keeping the engine running, use at least 1/2 the can, shut down the engine and disconnect the battery for 5 minutes, then restart and complete a number of mixed driving cycles, town, freeway, stop and go etc., after a few days the problem will go away as the system will relearn to the clean intake.

May 20, 2009 | 2000 Kia Sephia

1 Answer

Car stalls when idling at stop light


have the car checked when the check engine light is on,also a good scanner will be able to give you the history codes,get back to me with the codes and we'll go from there. you need someone with a professional scan tool

May 13, 2009 | 2000 Chevrolet Cavalier

1 Answer

Continous surging and stalling


Per your description, I would suspect a fuel pump issue. When the fuel pump is running the pump impeller heats up. On an older pump the impeller can begin to seize up and momentarily stops and starts. Some times it just stops and has to cool down for a couple of minutes, then is ok for a while.
To test this theory, when the engine stalls and stops, your mechanic can use a rubber mallet and hit the bottom of the gas tank, this will free the pump impeller and the car will start again.
Or, have him install a fuel pressure gauge and go for a drive. If the pressure begins to fluctuate and drop, you know the pump is causing the issue.
Good luck, let me know.
Regards,

Apr 30, 2009 | 1990 Buick Reatta

1 Answer

2000 neon .... stalls when coming to a stop


Try this procedure for stalls like this.
Here is the most common cause of surges and stalls and low idle, it is the idle speed control air-bypass valve and throttle valve, they get full of gunk over the miles and cause idle issues (stalls) like yours, Get a can of spray intake cleaner from any local parts store, not carb spray, intake cleaner, it is made by a company called CRC, remove the air intake hose to the engine, hold the idle high so the engine won't stall, then spray the can of cleaner into the intake while keeping the engine running, use at least 1/2 the can, shut down the engine and disconnect the battery for 5 minutes, then restart and complete a number of mixed driving cycles, town, freeway, stop and go etc., after a few days the problem will go away as the system will relearn to the clean intake.

Jan 09, 2009 | 2000 Dodge Neon

Not finding what you are looking for?
1996 Oldsmobile Bravada Logo

Related Topics:

590 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...