Question about 1993 GMC Yukon

1 Answer

AC BLOWER MOTOR

I UNDERSTAND THAT TO ACCESS THE AC BLOWER MOTOR , THE GLOVE BOX STORAGE INSERT HAS TO BE REMOVED. HOWEVER ONCE THAT PART IS REMOVED , WHAT SCREWS DO YOU REMOVE TO ACTUALLY HAVE A VISUAL OF THE ACTUAL UNIT ?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 625 Answers

Most of times they have tree bolts on a under the blower motor you can locate the motor because it has a two wire conector and
it is like circular on the lower side, if you can't find it and motor does not work turn a/c on and top close to that area with you hand and it might come on for a liitle so you can hear where is it
or go and buy one motor and do not loose the receipt so in case you have to return it,
but that way you see the phisical look of it, good luck and let me know

Posted on Jun 08, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change ac blower motor on s10 chevy truck 2001


Go to your passenger dash . It should be accessible under the glove box. It probably has old papers from the glove box or tree leaves. remove 3 to 4 7mm screws that hold it in place. Drop the fan and re-install the new one or clean out the old.

Jun 26, 2012 | Cars & Trucks

1 Answer

Where do you find the blower motor resistor


This part is typically attached to the blower motor. Access to the blower motor is normally through the glove box. Once removed. you should see both the blower motor and the resistor. The resistor will have 2 plugs and may be attached to the motor by a screw. This is the most common fix for heaters/AC that don't have all the fan speeds.

Jan 05, 2012 | 2004 Kia Rio

1 Answer

How to replace main heater fan


Blower Motor REMOVAL & INSTALLATION Front Fig. 1: Front heater blower motor assembly 89696g02.gif
Remove the glove box to access the front blower motor, which is on the firewall 89696p02.jpg
The blower motor is retained by four bolts (arrows) 89696p03.jpg
The blower motor vent tube helps to cool the blower motor for efficient operation 89696p04.jpg
Push up on the clip to remove the blower motor connector 89696p05.jpg
A ratchet with extensions makes removal of the retaining screws easier 89696p06.jpg
Lift the blower motor over the control cable . . . 89696p07.jpg
. . . and remove it from the vehicle 89696p08.jpg
  1. Disconnect the negative battery cable.
  2. Open the glove box door. Gently squeeze the retainers at the rear of the box inward and allow the box to swing downward. NOTE: If additional access is required, unfasten the glove box hinge retainers and remove the assembly.
  3. Label and disconnect the electrical harness from the blower motor.
  4. Remove the blower motor housing tube and/or blower motor cover.
  5. Remove the blower motor retaining screws.
  6. Remove the blower motor from the A/C evaporator. To install:
  7. Install the blower motor in the A/C evaporator and tighten the retaining screws securely.
  8. Install the blower motor housing tube and/or blower motor cover.
  9. Connect the electrical harness to the blower motor.
  10. Reinstall the glove box and close its door.
  11. Connect the negative battery cable.
Rear Fig. 2: Service cover push pin locations 89696g03.gif
  1. Disconnect the negative battery cable.
  2. Remove both rear passenger seats.
  3. Remove the three push pin retainers from the lower edge of the auxiliary heater and air conditioning service cover.
  4. Lift the service cover outward and upward to remove.
  5. Label and disconnect the electrical harness.
  6. Remove the blower motor housing tube.
  7. Loosen the three retaining screws and remove the blower motor. To install:
  8. Install the blower motor and tighten retaining screws securely.
  9. Install the blower motor housing tube.
  10. Connect the electrical harness.
  11. Position the service cover and install the three push pin retainers from the lower edge of the cover.
  12. Install both rear passenger seats.
  13. Connect the negative battery cable.
prev.gif next.gif

Dec 19, 2010 | 1998 Ford Windstar

1 Answer

How do I change a blower motor in a chrysler Town and country


Hello, to change the blower motor resistor follow this steps:
  1. Disconnect and isolate the battery negative cable.
  2. Open the glove box.
  3. Flex both sides of the glove box bin inward near the top far enough for the rubber glove box stop bumpers to clear the sides of the glove box opening, then roll the glove box downward.
  4. Reach through the glove box opening to access and disconnect the instrument panel wire harness connector for the blower motor resistor from the resistor connector receptacle.Blower motor Resistor
  5. Reach through the glove box opening to access and disconnect the blower motor pigtail wire connector from the resistor connector receptacle.
  6. Remove the two screws that secure the blower motor resistor to the evaporator housing.
  7. Remove the blower motor resistor from the evaporator housing.

Thanks

Aug 25, 2010 | 2006 Chrysler Town & Country

2 Answers

2005 Toyota Corolla. Bought it from a guy that lives in the country. Took apart ac cabin filter today and found LOTS of mouse or rat stuff. Vac a bunch out and got a new filter...now ac is making a loud...


removal of the blower motor is quite easy. you can access it from the passenger foot area. remove the glove box by removing the limit rod screw and squeezing the sides of the glove box together to remove. You can now better visualize the area. remove a few plastic clips that hold an electronics shelf and move it aside. remove the electrical connection to the blower ( take note of orientation of plug so that you put the motor back in the correct position) remove three screws that hold the blower in place. Pull blower assembly down. clean or replace blower. Rockauto.com sells a complete blower and fan assembly for very little $.

Aug 15, 2010 | 2005 Toyota Corolla

1 Answer

Where is the blower motor resistor in a 2001 dodge caravan se. I do not see it behind the glove box. I do see soemthing similar under the hood on the passenger side aginst the firewall but it is not...


Caravan, Grand Voyager, Town and Country, Voyager, 2000-2004
Blower Motor - Removal & Installation
  1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
  2. Remove the glove box from the instrument panel.

    a1b7373.jpg
    Fig. The blower motor is located behind the glovebox, behind the blower motor cover
  3. Remove the A/C-heater blower motor cover.
  4. Disconnect the blower motor wiring connector.
  5. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
  6. Remove the blower motor mounting screws.

    bdc6158.jpg
    Fig. Once the cover is removed, unplug the electrical connector and push it through the opening in the housing

    063bc30.jpg

    Fig. The blower motor is secured to the housing with three small screws
  7. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.
To install:
  1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
  2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
  3. Reconnect the blower motor electrical connector.
  4. Install the A/C-heater blower motor cover.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable. Check blower motor operation.


Auxiliary Heater and Air Conditioner
Blower Motor - Removal & Installation
  1. Disconnect and isolate the negative battery cable.
  2. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2. Remove the sliding door sill plate.
    3. Remove the quarter trim bolster.
    4. Remove the upper C-pillar trim and D-pillar trim panel.
    5. Remove the first and second rear seat belt anchors.
    6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.

      1dc958e.jpg
      Fig. Removing the trim panel to access the rear blower motor
    9. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
    10. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
    11. Pull first rear seat belt through the access hole.
    12. Remove the quarter trim panel from the vehicle.
  3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  4. Twist the blower motor out of scroll housing.
  5. Disconnect the blower motor wiring connector.
  6. Remove the blower motor from vehicle.

    1e2cfdc.jpg
    Fig. The rear blower motor is held in place by four screws
To install:
  1. Install the blower motor unit into the vehicle.
  2. Reconnect the blower motor wiring connector.
  3. Secure the blower motor into scroll housing.
  4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  5. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    9. Install the D-pillar trim panel and upper C-pillar trim.
    10. Install the quarter trim bolster.
    11. Install the sliding door sill plate.
    12. Install the second rear seat, if equipped, and install the first rear seat.
  6. Reconnect the negative battery cable. Check blower motor operation.

Hope helps (remember rated this).

Jul 11, 2010 | 2001 Dodge Grand Caravan

2 Answers

How do i change the ac/heater blower motor in 96 isuzu rodeo?


I assumed it's a v6
you need to remove the glove box compartment
remove the screws on the blower motor housing
remove the motor

Feb 26, 2010 | 1996 Isuzu Rodeo

2 Answers

Replacement of a new blower motor


there is a small cover on pass side of dash below glove box..remove this and you will see blower motor..remove screws from motor..a couple are little hard to get at..a motor costs about 80bucks..if you're not sure you can do it,consult a mechanic

Jun 03, 2009 | 1998 Dodge Caravan

2 Answers

Honda Civic heater / blower noise.


you need to remove your glove box assy.(beleave only 2 screws and pivot clips) make sure its not anything from glove box that has slipped behind. once box is out uf way you can access easier the blower motor assy. it actually attaches into blower box from bottom side. when looking at you will find three screw/bolts fastening motor to casing. remove those and then slowly lower motor and fan cage(attached to motor shaft) out from housing. sometimes it takes a little convincing to come out but not real tough. once out you most likely find the object causing noise in fan cage or resting up on lip area of housing unit. once found install in reverse order. let me know if this helps or if we need to dig a little deeper into! good luck!
joel

Feb 02, 2009 | 1999 Honda Civic

3 Answers

Blower motor resistor replacement


the relays are behind the glove box. you have to take the glove box out to have access to the relay for the heating system 

Dec 10, 2008 | GMC Sierra 1500 Cars & Trucks

Not finding what you are looking for?
1993 GMC Yukon Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...