Question about 2000 Buick LeSabre

1 Answer

How do you reset abs brake light on a 2000 buick lesabre?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Buick Master
  • 4,362 Answers

There is not a reset, but rather a current malfunction. Check fluid levels and all wiring and connections, espeically at wheels...

Posted on Oct 24, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 184 Answers

SOURCE: 2000 buick lesabre abs light

It may be an ABS sensor... however you'll want to get those ABS codes read. A regular code reader doesn't do that, you'll need a specific ABS code reader or take it to a shop.

Posted on Mar 23, 2009

  • 6 Answers

SOURCE: 1995 LeSabre ABS light

the anti-lock brake system is part and parcel of the traction control system. the abs has a $750.00 valve located in the engine bay on the right side (as you face the car from the front) the driver's side just behind the headlight. i had a mechanic who took it upon himself to remove, dismantle and clean and reassemble the unit, all to no avail but also without expense. the cost of the part was prohibitive since Blue Book on this car is just about $700.00. it will run and brake just fine without the abs or the traction control system either.

Posted on Nov 01, 2008

  • 14092 Answers

SOURCE: buick lesabre 2000 head lights won't shut off

SOUND LIKE THE DRL RELAY IS STICKING CLOSE.ITS NOT TURNING OFF CIRCUIT LIKE IT SUPPOSE TO.HAS TO BE REPLACE.

Posted on Sep 11, 2009

daves944
  • 1050 Answers

SOURCE: abs & traction light on 1997 buick lesabre

This is a fairly common problem, Gm has actually issued a service bulletin regarding this repair. The problem probably originates from one of your wheel speed sensors that is mounted inside one of your front wheel bearings. To be sure, you need to have the car scanned to find out which one and then you have to replace the whole bearing assembly because the sensor is integral to the bearing. The bearing is not hard to do but you will need some professional tools if you want to do it yourself. At a shop it should cost between 3 and 400 dollars complete.

Posted on Jan 10, 2010

  • 1608 Answers

SOURCE: 2001 Buick Lesabre ABS light stays on even

What this means is that the abs module is seeing a problem in the abs system.This has nothing to do with the regular brakes.What you need to do is get the codes from the abs module and this will help in finding what could be causing the light to come on.When the abs light comes on the regular brakes will work normally but your abs brakes will be disabled.Let me know what codes you find and I can help or explain what the cause could be.Good luck.

Posted on Jul 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i turn off the abs light in a 2000 buick lesabre


Do you know why the light is on? The light comes on cause a fault has been detected in your ABS system. Not taking care of the problem will only ensure that the light will come back if reset. Have your vehicle scanned and post your findings. Also look at the wiring for the front wheel bearings if you find any of the wires broken this is most likely why your ABS light is on. Broken abs wires is a common issue.

Feb 25, 2013 | 2001 Buick LeSabre

1 Answer

My abs light on my 2000 buick lesabre will not shut off i have replaced rotors and pads what could the problem be


The warning light indicates that there is a malfuction in the anti-lock Brake System (ABS). Normally the system will then cease to function so you have a conventional braking system with no anti-lock feature to engage if you lock up the wheels on braking.

This ABS fault warning has nothing to do with the condition of the pads and rotors so renewing them, which is essential for good braking performance, will not solve the problem.

You will need to take the vehicle to a mechanic with the correct equipment to diagnose the cause of the ABS warning. It may be as simple as a failed ABS sensor (or sensors) and that is what I would be checking first.

It is quite safe to drive the vehicle with the ABS disengaged because your brakes will operate normally. What you don't have is the ABS kicking in to release the brake pressure temporarily in the event you brake hard and lock up any of the wheels.

Sep 05, 2011 | 2000 Buick LeSabre

1 Answer

2000 buick lesabre with abs-low brake pedal after changing all 4 rotors and pads. did not open the hydraulic system


When changing pads and you push the caliper in for the new pad you should open the bleed screws. , then close and re-assemble. press pedal and open bleed screw and let it drip a little . gravity bleed. Did you turn the read caliper piston in and then press it down? The rear piston must be aligned with the pad. Did you pump the parking brake to reset?

May 20, 2011 | 2000 Buick LeSabre

3 Answers

Does my 1995 buick lesabre limited have abs brakes? this car is loaded to the gill's,


The easy way to tell is when you turn the key to start the vehicle the vehicle goes through a bulb check.If there is a light that says anti lock on the instrument cluster,you have ABS brakes.Hope this helps.Good luck.

Aug 17, 2010 | 1995 Buick LeSabre

1 Answer

2001 Buick Lesabre ABS light stays on even resetting the system. brakes are good and responding just the light coming on and off.


What this means is that the abs module is seeing a problem in the abs system.This has nothing to do with the regular brakes.What you need to do is get the codes from the abs module and this will help in finding what could be causing the light to come on.When the abs light comes on the regular brakes will work normally but your abs brakes will be disabled.Let me know what codes you find and I can help or explain what the cause could be.Good luck.

Jul 28, 2010 | 2001 Buick LeSabre

1 Answer

ABS & Brake warning lights turn on


it is possible but its also possible you have a wheel speed sensor acting up. you would have to have it scanned for codes

Jul 09, 2009 | 2002 Buick LeSabre

1 Answer

Engine Collant, ABS & Brake lights on CC/cig. lighter not working


Replace coolant level sensor in radiator. The wheel sensor may be the abs problem. You will need to hook to a diagnostics tool to find the cure. Check vac hoses to cruise unit for leak.

Jun 11, 2009 | 2000 Buick LeSabre

2 Answers

Indicator lights come on and go off


Hi when the ABS and TRACTION light come on there is a FAULT CODE STORED in the EBCM
I need the code before I can help you

May 18, 2009 | 1997 Buick LeSabre

Not finding what you are looking for?
2000 Buick LeSabre Logo

Related Topics:

2,068 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...