Question about 2003 Dodge Stratus

1 Answer

I need to replace the crank shaft sensor. Where is it located?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

Im havin the same problem too.i did replace the crank shaft sincer.with no luck.i think it may be the plug that is conected to the sincer. the only other thing it camn be is the computer.

Posted on Nov 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft position sensor located on a 2003 Mitsubishi Galant 4 cylinder


Hello, crank position sensor located at the 2 o`clock position hidden behind timing cover and crank shaft pulley. If you look closely in well lit area or use a flashlight you can follow the (CCPS) harness down the right hand side of timing cover to where it goes into lower timing cover on lower right hand side of crank shaft pulley. It can be replaced with out removing timing belt. Please note if the 60,000 miles heavy service interval for timing belt is needed and water pump condition should be observed when repairing the crank position sensor.

Feb 21, 2018 | 2003 Mitsubishi Galant

1 Answer

Where is crank shaft sensor location on 95 lexus sc300 please help


images for Where is crankshaft sensor location on 95 ...

eplaced engine on '97 SC300 now new engine does not have Crank ...

www.clublexus.com/.../633233-replaced-engine-on-97-sc300-now-new-...
May 4, 2012 - Location: arizona. Posts: 3 ... apparently 95-97s had an additional crank sensor. .... 1995 Lexus SC300 5spd Na-T ( TT Ecu Mod + a few others) 2jzge position sensor??
Nov 2, 2011
SC400 Crank Shaft Position Sensor. WHERE?????
Oct 11, 2011
SC300 No Spark
Oct 2, 2010
What happens if the Camshaft Position Sensor goes bad?
Jun 18, 2009
More results from www.clublexus.com

Lexus Crank Position Sensor ' LS400 SC300 ES300 GS300 ...

www.partsgeek.com > Crank Position Sensor > Lexus Parts & Accessories
Products 1 - 10 of 68 - 95 1995 Lexus LS400 Crank Position Sensor Denso NLA 7/13 ... 96 1996 Lexus SC300 Crank Position Sensor Denso Includes Pigtail.

Jan 27, 2016 | Lexus Cars & Trucks

1 Answer

Where is the 2nd crank shaft sensor located, and is there a diagram to show where these sensors are located?


is it a no crank or crank no start?
Possible causes for code P0335
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery

Read more: http://engine-codes.com/p0335.html#ixzz3Cxw6SN6O

Sep 10, 2014 | 2004 Buick Rendezvous

1 Answer

Replace crank sensor in 89 olds cutlass calais


Scottykw I have an 88 Oldsmobile Cutlass Calais quad 4,2.3L needing help locating the knock sensor on my car,rough idling and slow and sluggish acceleration.ive replaced the crank shaft position sensor and spark plugs,and fuel filter and allot of other things, but not the knock sensor or the Mass air flow sensor...where can I locate the knock sensor?

Apr 03, 2013 | 1989 Oldsmobile Cutlass Ciera

1 Answer

Were is the cam shaft senor and the crank shaft senor located


this car does not have a camshaft sensor the distributor pick up coil acts as a cam sensor here is crank sensor info the crank sensor is located in front of engine just behind the crankshaft pulley using ohmmeter check resistance between terminals on sensor replace is not within specs cold 1630-2740 ohms hot 2065-3225 ohms if this is not the problem please reply to your post ill monitor it. hope this helps

Jul 26, 2010 | 1996 Toyota Corolla

1 Answer

I need to replace my Crank shaft position sensor. Where exactly is it located under the hood?


What year, make model of vehicle are we talking here, and what engine??

May 17, 2010 | Cars & Trucks

2 Answers

My 97 sunfire has a bad cranck shaft sensor. where is that located? would it also make the car not start?


Yes it would and will make the car not start. Your crank sensor is located behind your harmonic balancer, which is the large pulley that turns all the belts. THe one that is coming off the crank shaft.

Apr 10, 2010 | 1997 Pontiac Sunfire

1 Answer

Ive replaced the cam shaft sensor but need to see about fixing the crank shaft sensor and do not know where its located


The crank shaft sensor is located on the front of the engine under the timing cover. In order to replace it you will need to remove the timing belt.

Jan 22, 2010 | Chrysler LHS Cars & Trucks

Not finding what you are looking for?
2003 Dodge Stratus Logo

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...