Question about 1999 Dodge Durango

Open Question

MY CAR STEREO WAS STOLEN AND NOW MY TRUCK WONT START WHEN I TURN THE KEY THERE IS NOW SOUND AT ALL WHAT DO I HAVE TO DO TO GET IT TO RUN AGAIN

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 160 Answers

SOURCE: 1999 Chevy Silverdo cranks but wont start

ok check your timming belt then your ckt sensor the chip will not let the truck even crank or let the dash come on

Posted on Dec 07, 2008

Ad
  • 159 Answers

SOURCE: car wont start up right away

Crank or cam sensor probably as plugs bad plugs would start but miss the sensor will either give a start or no start condition and on 1 truck the crank sensor went out and it would run cold but miss like crazy when warm,I work in a chyrsler shop and have never seen that happen and even a scan tool didn't pick it up.

Posted on Mar 12, 2009

  • 289 Answers

SOURCE: getting fuel andengine running in start position

it sounds like ignition switch is faulty thats why it stalls when u turn back to run

Posted on Apr 17, 2010

cansmo
  • 2431 Answers

SOURCE: my 2007 dodge caliber wont start

You are dealing with 2 possible problem. The ignition switch,or the alarm, If you have a alarm problem the vehicle will crank then in 2 seconds shut down,this is because the key is recognized,now if this is the problem roll down a window and disconnect the negative battery terminal,put the key in the ignition but in the off position.After 5 minutes reconnect the battery and turn the ignition on but dont crank the engine leave for 1 minute. Then see if that resolved the issue.Now if its an ignition switch problem crank the engine and slowly let it go.try to keep the key in the position where it stays running. By the way there is a campaign of a recall dealing with a TIPM software update Re-configure ,anti-theft system. Customer satisfaction notice G42. You will have to see the dealer for this campaign.

Posted on Nov 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2002 cadillac seville sls wont start have power to every thing , i go to start .... it wont turn over ? the radio was stolen out of it , would that have any thing to do with it ?


It shouldn't, you can contact your local dealership to make certain but I would check the starter. It is located under the upper intake manifold.

Nov 22, 2016 | 2002 Cadillac Seville SLS

1 Answer

Pt cruiser wont start. checked battery, starter , releighs and ignition, and they seem fine. no codes come up when turning the key 3 times


To do self diag on a pt u need to start with ignition off. Hold trip button in for the odometer keeping trip button held down turn ignition key to run then release trip. This will also run a self test on instrument cluster. Codes will be displayed in the odometer at the end of test

Nov 01, 2016 | Chrysler PT Cruiser Cars & Trucks

1 Answer

1999 f150 turns over fine, at times wont run


When it won't start is there spark , does the check engine light come on when you turn the key on ? What's battery voltage at when it won't start , is the charging system working . When it won't start check power an grounds to the PCM/ECM - engine computer , your need a PCM/ECM connecter pin out .

Jan 22, 2016 | Cars & Trucks

11 Answers

Changed ignition switch now security light stays on and truck starts and kills


You need to relearn the passlock system (security). There are 2 ways. One is with a scanner, which most diy'er wont own an expensive one to do it this way, here is the manual way. Start the truck and let it run until it dies. The security light should then be flashing. Leave the key in the run position until the security light stops flashing (about 10-15mins). After the light stops flashing turn the key off. Try to start the truck again. It should do the same thing (run for a few seconds and then die with the security light flashing). Again wait for 10-15 mins for the light to stop flashing and then turn the key off and repeat the process one last time. That's a total of 3 times. Once you finish the process the 3rd time. Let the truck sit for a minute with the key off. It should now be programmed and start and run normally.

Jun 02, 2014 | 1999 Chevrolet Silverado 1500

1 Answer

Car wont start up right away


Crank or cam sensor probably as plugs bad plugs would start but miss the sensor will either give a start or no start condition and on 1 truck the crank sensor went out and it would run cold but miss like crazy when warm,I work in a chyrsler shop and have never seen that happen and even a scan tool didn't pick it up.

Mar 09, 2009 | 1998 Jeep Cherokee

1 Answer

S-10 won't start


Try replacing the fuel sending unit first. Then check your ignition relays. Are you ruining any codes. because for the most part your truck will tell you whats wrong if your pump is bad it should run a low fuel pressure code and if there is something with the ignition you might run a oxygen sensor code. when you turn it over do you smell gas.

Oct 22, 2008 | 1999 Chevrolet S-10 Pickup

Not finding what you are looking for?
1999 Dodge Durango Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...