Question about 1998 Nissan Quest

Open Question

I have a Astroflex J5F-TX1000 I'm wondering how to activate, cause all it does is blink once when I push the button. command starter

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

May i know the model no for astroflex in which antena no 198-058-201-01 6F05 astroflex


astroflex is owned by Astrostart, their phone is 1-800-361-7271

Nov 24, 2014 | 2003 Ford Focus

2 Answers

Reprogram astrostart j5f tx2000


Get under the dash or where the unit is located.
You will see 8 or 9 dip switches on the unit with an LED beside them.
Turn switch 1 and 8 on.
Press and release the brake. (LED will flash)
Press and hold start button on remote. (LED will flash and parklights will flash once.
Turn switch 1 and 8 to off.
Press and release the brake (LED will flash once)
In future would be a good idea to supply vehicle details etc as can sometimes be a known condition , that saves time looking it up , good luck

Nov 18, 2014 | Cars & Trucks

2 Answers

Astrostart won't start the car


You may need to reset the system.

SEQUENCE ACTIVATED BY THE PARKING BRAKE .
1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
2. Move gearshift lever to neutral.
3. Apply the parking brake Once Twice
Note: The system can be set - at time of installation - to require that the parking brake be applied once or twice.
If set for two actuations, pause one second between the two.
4. Remove key from ignition (the system keeps the engine running).
5. Exit the vehicle.
6. Within 60 seconds, close all doors.
7. The system will stop the engine and blink the parking brakes once to confirm the sequence is valid (vehicle is
ready for a remote start command).
SEQUENCE ACTIVATED BY THE REMOTE CONTROL
1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
2. Move gearshift lever to neutral.
3. Apply parking brake.
4. Send the start command (Model 801 & 2101 - Model 903 ).
5. Remove key from ignition (the system keeps the engine running).
6. Exit the vehicle.
7. Using the remote, send the STOP command. The system will stop the engine and parking lights will blink once
to confirm that the sequence is valid (vehicle is ready for a remote start command).
http://www.astrostart.com/Support/Guides.aspx

Nov 27, 2012 | Cars & Trucks

1 Answer

Problems starting bmw with push start button


It may be corrosion; If you hear a louder "click" it may be the contact on the starter solenoid down on the starter. If this is a recent development, this is a likely cause.

it is less likely but still remotely possible the push button itself has corrosion issues, or there is enough debris to insulate the contacts electically.

Dec 19, 2011 | Cars & Trucks

1 Answer

On my bmw2006 330i it seems that the ignition is not really off after stopping the car. After stopping the engine with the start/stop button and removing the remote key from the slot, the button remains...


In your car the engine starts this way: a code stored in the remote key is sent wirelessly to the receiver in the receptacle (thru its coil antenna) which sends it to the ECM to activate it; then the starter button sends the command for the actual starting.
In your case the receiver appears to keep the code in memory when it shouldn't. Have it replaced. BTW this has absolutely nothing to do with the ignition coil.

Sep 12, 2011 | 2006 BMW 3 Series

1 Answer

My astroflex starter cranks engine over and over but does not start engine. I can only stop it by turning off the main power switch.


STARTER RELAY SWITCH IS BAD IT.S IN THE FUSE BOX UNDER THE HOOD ONCE LIFT THE COVER OFF AND TURN IT OVER IT WILL TELL YOU WHERE IT.S LOCATED AT

Mar 29, 2011 | 2003 Ford F150 Regular Cab

1 Answer

Manual for ASTROFLEX j5f-tx1000 command start.


Try this one
http://www.astrostart.com/Support/Guides.aspx

Sep 18, 2010 | Nissan Quest Cars & Trucks

1 Answer

How do I reprogram two remote starters for my 2007 Chevrolet Tahoe?


on the right of the speedo cluster, press the second button down on that set, continue to push until you see relearn remote. once you see relearn push and hold the check button, which is the bottom button on the same set of buttons. Hold it for about 5 seconds it will say relearn active. Then you hold down the lock and unlock at the same time on the remote for about 5 seconds, you will then hear a beep. Do the same with the other remote. Then its done! to close out just push the same button you started with, second from the top.

Nov 10, 2009 | 2007 Chevrolet Tahoe

1 Answer

Astroflex 2100 autostart won't start all the time


you need to reprogram the tach as it may be a little stronger or weeker in your current van

Oct 10, 2009 | 2009 Chrysler Town and Country

Not finding what you are looking for?
1998 Nissan Quest Logo

Related Topics:

311 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...