Question about Saturn SC1

1 Answer

Rear brake springs

Which spring goes in front? the angled one or the longer one i'm having trouble with the adjuster. i put the heaver longer spring in front the one that hooks onto the piece that pushes up against the adjuster and it pulls up on the adjuster .does the angled smaller spring go in front. i dont have a manual..

thanks chris
2002 sc 1 series saturn

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 359 Answers

It should be the right one if you have it back to front the adjuster wont work the spring that sits across the adjuster is flat where it covers the adjuster and coiled everywhere else

Posted on Jun 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove and clean and replace the rear brakes on a 2008Toyota yaris


REMOVING REAR BRAKE DRUM SUB-ASSEMBLY
1. Release the parking brake and remove the rear
brake drum.
If the rear brake drum cannot be removed easily,
do the following:-
2.Remove the hole rubber and insert a screwdriver
through the hole into the backing plate, and hold the
automatic adjust lever away from the adjuster.
3.Using another screwdriver, contract the brake shoe
by turning the adjuster.
4. Take out the brake drum from the flange.
5. remove the shoe hold down spring cup, shoe hold down spring, pin and front side brake shoe.
6. Remove the tension spring. Remove the shoe return spring from the rear brake shoe and remove the parking brake shoe strut set.
7. Remove the shoe holding spring cup, shoe hold spring, pin and rear brake shoe.
8. separate the parking brake cable.
9. Remove the automatic adjust lever tension spring and remove the automatic adjust lever.
10. remove the C-washer and remove the parking brake shoe lever.
NOTE: Do not use any solvent like gasoline to wash the brake parts.
Always wear safety goggles and mask before using compressed air.



Dec 28, 2013 | Cars & Trucks

1 Answer

Need help putting on rear brakes on a 2004 pontiac grand am


shoe breaks are tricky but can be a little easier with practice and the right tools;
What you;ll nned:
Spring pliers
Shoe hold down tool
Diagonal side cutters.
Needle nose pliers
Flathead screw driver.

this project is easy so long as you can remember how the parts go back together.

!. remove brake drum.
2. see how the brakes fit together. REMEMBER HOW THE BRAKE BAR GOES BACK IN. IT ONLY WORKS CORRECTLY ONE WAY!

the brake bar is the metal piece that goes between the brake shoes.
3. remove the brake shoe springs with the spring pliers. *THE BRAKES HOW HIGH POWERED SPRINGS AND SHOULD BE HANDLED CAREFULLY*
4. remove the brake shoes with the spring tool.
5. clean parts thoroughly with brake part cleaner. (i like spraying it into a glass jar and shaking it a little) you can use a wire wheel to brush to clean the harder material.
then take some brake cleaner and spray down the backing plate and remove any and all grease and old brake material.
6. using brake grease, dab a small amount on the adjuster and the small oval shaped pads on the backing plate, *use a SMALL AMOUNT* less then a finger nail in size.
7. reassembly, now compare the shoes and take note that there are 2 long and 2 short shoes.
thte larger shoes go in the front and the smaller go to the rear of the vehicle. set the pairs aside so you do not confuse them. next a fix the shoes to the backing plate and then set the adjuster to the lowest setting, (shortest). and set the brake bar in place then set the springs (the longer springs)
8. adjusting the shoes. slip the drum on the hub and spin the brake, it should feel like it has a bit of drag. keep slipping the drum on and off making adjustments to the adjuster till the drum either is adjusted correctly or you cannot remove it, if you need to adjust the brake further there is an access in the backing plate for further adjustment.

Apr 18, 2011 | 2004 Pontiac Grand Am

1 Answer

How to change rear barke shoes


Brake Drums & Brake Shoes Removal & Installation To Remove:
Rear Drum Brakes kia-09-18-7627.gif

  1. Raise and safely support rear of vehicle.
  2. Release parking brake.
  3. Remove rear wheel assemblies. NOTE: If brake drum is stuck, install two 8 mm bolts into threaded holes and tighten evenly.
  4. Remove top return spring, front and rear shoe spring clips and hold-down pins.
  5. Remove anti-rattle spring and adjuster spring. NOTE: Note position of operating lever prior to removal.
  6. Remove bottom return spring.
  7. Remove clip and washer and detach parking brake cable from rear shoe.
  8. Remove brake shoes.
To Install:
  1. Lubricate all brake shoe contact points with appropriate grease.
  2. Place operating level into position on hub.
  3. Install rear brake shoe and connect parking brake cable to rear shoe with washer and clip.
  4. Install front brake shoe and install bottom return spring.
  5. Install hold-down pins and spring clips.
  6. Position operating lever and install top return spring.
  7. Install anti-rattle spring and adjuster spring.
  8. Install brake drum and screws.
  9. Adjust brakes and install rear wheel assemblies.
prev.gif next.gif

Jan 21, 2011 | 2003 Kia Spectra

1 Answer

Diagram for right rear brake assembly for a 1993 chrylser lebaron


it's a standard leading trailing bendix brake system, small shoe to the front, larger shoe to the rear. The spring are ease. THE springs that look the same go behind the shoes, the biggest spring goes at the top of the brake assembly, and the spring thats medium goes on the bottem. Don't forget the horse shoe clip to the e-brake cable. The adjustment peice goes near the top. Adjust it all the way and spin the drum while you use the mopar adjustment tool to set the e-brake adjust ment. you should get 1/2 to one full rotation before the drum drum stops spinning. don't forget to gravitey bleed your brake (open the rear bleed screws at the same time, then the front).

Oct 16, 2010 | Chrysler LeBaron Cars & Trucks

2 Answers

How to remove brake rotors on a 1996 ford explorer


How to replace the rear brake pads on a 1995 through 2001 Ford Explorer The system utilizes a drum-in-hat type rear brake rotor. The integral drum allows the use of a drum-and-shoe type parking brake system. All other components are similar to their front disc brake components Remove the two bolts on either side of the brake hose with the rubber boots. Do not remove the four bolts where the axle ties in. The two bolts to be removed require a 10mm socket/wrench. Loosen the pads from the caliper Rotor Removal In order to take the rotors off (replace with new or have them machined), it is best to loosen the emergency brake shoes. To do this, behind the rotors, in the back there is a rubber plug, remove that and you can use a screw driver to engage the teeth of the adjusting screw, turn it clockwise to loosen, usually 10-20 teeth. Usually this means turn it downward. After this, it may still be difficult to get the rotors off without tapping them. Use a rubber mallet and hit them from behind. Before really whacking the rotor, make sure you have loosened the adjusting screw enough. It may take heavy swings of the rubber hammer to do this. It will eventually break loose. Parking Brake You might want to check the parking brake while you are here. To remove:
  • Remove the rear disc brake rotor.
  • Remove the outboard return spring.
  • Remove the adjusting screw spring.
  • Remove the rear brake shoe hold-down spring and pin.
  • Remove the brake shoe adjusting screw and nut.
  • Remove the front brake shoe hold-down spring and pin.
  • Remove both parking brake shoes and the inboard return spring.
  • Check the parking brake lever for excessive wear and replace as necessary.
To install:
  • Position the front parking brake shoe to the backing plate and install the hold-down pin and spring.
  • Install the rear parking brake shoe with the inboard return spring.
  • Position the brake shoe adjuster screw and nut on the shoes and install the rear shoe hold-down pin and spring.
  • Install the brake shoe adjuster spring.
  • Install the outboard return spring.
  • Adjust the parking brake shoes and install the rotor, caliper and wheel.
  • Lower the vehicle and tighten the wheel lug nuts to 100 ft. lbs. (135 Nm).
ADJUSTMENT
  • Measure the inside of the drum portion of the rear brake rotor
  • Remove the rear disc brake rotor.
  • Using Brake Adjustment Gauge D81L-1103-A or equivalent, measure the inside diameter of the drum portion of the rear disc brake rotor.
  • Subtract 0.020 in. (0.508mm) from the first measurement, adjust the brake shoes to that size
  • Adjust the parking brake adjuster screw until the outside diameter of the parking brake shoes measures 0.020 in. (0.508mm) less than the drum measurement.
  • Install the rear disc brake rotor.
Reassembly Reassembly is easy. Put new or machined rotors back on by sliding them over the lugs (they should slide on easily.) Loosen bleeder valve (having a catch bottle handy is good). Push calipers in slowly (using a c-clamp or large channel lock pliers), close bleeder valve. Put on pads. Lubricate metal clips with small amount of anti-seize. Re-adjust the emergency brake by turning the opposite direction from loosening. Refill the brake master cylinder

Aug 09, 2010 | 1996 Ford Explorer

2 Answers

1997 Ford contour rear brake shoe replacment help.


Brake shoe removel:

Depress and turn the retainers for the hold-down springs and pins to remove them from each shoe. Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.

Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.

Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.

Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xgUqun
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xdByQ8

  • Step 2 Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xVyUAt

  • Step 2 Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xVyUAt

    Jul 17, 2010 | 1995 Ford Contour

    1 Answer

    Drum brake spring location


    hi, the spring i think you are talking about will be the spring for the handbrake/parking return where the handbrake comes into the back of the drum there will be two holes one on either brake shoe, just below where the handbrake adjuster is fitted it is verry hard to put it in the holes but it does go eventually....hope this helps

    Feb 21, 2010 | 1997 Toyota Corolla

    1 Answer

    Need diagram for rear brake spring assembly on a 1994 toyota tercel


    The bottom spring should be hooked into a small hole on thefront shoe bottom, and to the adjuster cam on the other(rear) shoe. The remaing two spring are one long and one short. The shorter spring goes from the front shoe to the post and the longer spring goes from the rear shoe to the post. Just a suggestion, when you are dissasembling anything complex like this, it's a good idea to take a few digital pix along the way. Good luck my friend,Dana P.S. if you haven't taken the other side apart yet you can use it for a reference only mirror the assembly.

    Sep 06, 2009 | 1994 Toyota Tercel

    1 Answer

    Remove and replace rear brake shoes on 2004 honda accord


    Brake Shoes Removal & Installation To Remove:
    1. Raise and safely support rear of vehicle.
    2. Remove rear wheel assemblies.
    3. Release parking brake.
    4. Remove brake drum.
    Rear brake shoe assembly


    6c57c70.gif
    1. Using an appropriate brake spring tool, unhook upper return spring from rearward brake shoe.
    2. Push retainer springs IN and turn to remove tension pins.
    3. Lower brake shoe assembly and remove lower return spring.
    4. Remove brake shoe assembly from back plate.
    5. Disconnect parking brake cable from lever and remove brake shoe.
    6. Remove parking brake lever from brake shoe.

    To Install:

    d36458c.gif
    1. Install parking brake lever to rearward brake shoe.
    2. Secure lever to brake show with a NEW U-clip.
    3. Pinch U-clip closed.
    4. Connect parking brake cable to rearward brake shoe.
    5. Install self-adjuster lever spring on front brake shoe.
    6. Assemble clevises, adjuster bolt and upper and lower return springs.
    7. Apply a light coat of grease (Molykote 44MA or equivalent) to sliding surfaces.
    8. Install brake shoe assembly onto back plate.
    9. Install tension springs.
    10. Using an appropriate brake spring tool, unhook upper return spring to rearward brake shoe.
    11. Install brake drum.
    12. Install rear wheel assembly.
    13. Lower vehicle.
    14. Adjust self-adjusting brakes by pressing brake pedal several times.

    Jul 13, 2009 | 2004 Honda Accord

    1 Answer

    I need a schematic for the rear brakes on an F150 super cab with 4.6L automatic trans 4wheel drive


    Drum, Rear Brake System Standard Rear Brake
    9969082.gif
    Item Part Number Description 1 2069 Brake Shoe Hold-Down Spring Pin 2 — Rear Wheel Cylinder Retaining Bolt (2 Req'd) 3 — Washer (2 Req'd) 4 — Anchor Pin (Part of 2211) 5 — Wheel Cylinder 6 2028 Brake Shoe Anchor Pin Guide Plate 7 2A637 Parking Brake Lever 8 2296 Brake Shoe Retracting Spring (Short) 9 2296 Brake Shoe Retracting Spring (Long) 10 2200 Rear Brake Shoe and Lining (Secondary) 11 — Washer 12 2106 Parking Brake Lever Pin Retainer 13 — Brake Shoe Adjusting Lever Cable Guide 14 2A642 Primary Brake Shoe Parking Brake Lever Link 15 2A601 Parking Brake Link Spring 16 2068 Brake Shoe Hold-Down Spring 17 2A176 Brake Shoe Adjusting Lever 18 2048 Brake Shoe Adjusting Screw Socket 19 2047 Brake Shoe Adjusting Screw Nut 20 2041 Brake Adjusting Screw 21 2049 Brake Shoe Adjusting Screw Spring 22 2200 Rear Brake Shoe and Lining (Primary) 23 2A178 Brake Shoe Adjusting Lever Cable 24 2211 Brake Backing Plate
    Heavy Duty Rear Brake
    6dcb5d2.gif
    Item Part Number Description 1 — Rear Wheel Cylinder Retaining Bolt 2 00538 Lock Nut 3 2212 Rear Brake Backing Plate 4 2262 Rear Wheel Cylinder 5 2A642 Primary Brake Shoe Parking Brake Lever Link 6 2A601 Parking Brake Link Spring 7 2A637 Parking Brake Lever 8 2106 Parking Brake Lever Pin Retainer 9 — Parking Brake Lever Bolt 10 — Secondary Shoe Assembly 11 2A179 Brake Shoe Adjusting Lever Cable Guide 12 2068 Brake Shoe Hold-Down Spring 13 — Adjusting Lever Pin 14 — Adjusting Lever Return Spring 15 2A176 Brake Shoe Adjusting Lever 16 2047 Brake Shoe Adjusting Screw Nut 17 2049 Brake Shoe Adjusting Screw Spring 18 2041 Brake Adjuster Screw 19 — Primary Shoe Assembly 20 2068 Brake Shoe Hold-Down Spring 21 2200 Rear Brake Shoe and Lining 22 2035 Brake Shoe Retracting Spring 23 2A178 Brake Shoe Adjusting Lever Cable 24 2092 Brake Adjusting Hole Cover 25 2069 Brake Shoe Hold-Down Spring Pin
    The rear drum brakes:
    • Have internal shoes that expand against the brake drum (1126).
    • Are a single-anchor type.
    • Are actuated by one rear wheel cylinder (2262).
    • Have two pistons in the rear wheel cylinder (2261). One exerts force against the upper end of the primary shoe; the other exerts force against the upper end of the secondary shoe.
    • Adjust rear brake shoes and linings (2200) automatically.
    • Need manual brake adjustment if the adjusters are not operating properly or after the rear brake shoes and linings have been replaced.
    When the brake pedal is applied, hydraulic fluid pressure forces the pistons in the rear wheel cylinder outward, moving the rear brake shoes and linings against the brake drum.
    The rear drum brake system includes the parking brake mechanism. Refer to Section 206-05 .

    Apr 04, 2009 | 1997 Ford F150 Regular Cab

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    101 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Saturn Experts

    yadayada
    yadayada

    Level 3 Expert

    60541 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21927 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6811 Answers

    Are you a Saturn Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...