Question about 1999 Pontiac Bonneville

1 Answer

Replacing upper intake plnum - 1999 Pontiac Bonneville

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 760 Answers

Very simple,just make sure you keep track where all the vacuum,sensor,and fuel lines go,also make sure you torque the intake back to specs.










TIM...........

Posted on Oct 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove intake manafole


The intake is two pieces, upper and lower, I assume you are replaceing theknoock senors? In any event here is a link to a video on how to remove the upper intake manifold. 1995 1999 Nissan Maxima Upper intake manifold replacement

Oct 12, 2016 | 1996 Nissan Maxima

Tip

How To Change The Spark Plugs On A 2002-2005 Kia Sedona 3.5 Liter


You'll need to remove the oil cap and the 6 bolts holding on the engine cover. The front 3 spark plugs are pretty easy to replace. You'll need to unplug the spark plug wire from the coil and disconnect the electrical connector. Unbolt the 2 10mm bolts holding the coil to the valve cover. Twist the coil and boot back and forth and pull it out of the cylinder head. The spark plug is down in the head, you'll need at least a 6 inch extension with a 5/8" spark plug socket, a telescopic magnet will help get the spark plug out of the head. The back 3 spark plugs involve removing the upper intake and throttle body, unbolt the bracket to the throttle body, and the bracket bolted to the upper intake manifold. on the back side of the engine. Remove the tubing from the throttle body to the air cleaner box. Unbolt anything else bolted to the upper intake. Unplug electrical connectors to the throttle body and any other electrical connectors on the upper intake and remove the upper intake bolts. And move the upper intake out of the way, there are only spark plug wires on the back 3 plugs. Twist and turn each boot to aid in removing the boot from the plug. I would get a new upper intake gasket and consider replacing the wires at this time also. There are actually only 3 spark plug wires, so for what is involved to get to them, I would replace them. I have found alot of the wires will arc to the upper intake manifold.

on May 02, 2010 | Kia Sedona Cars & Trucks

Tip

How to remove/replace the Valve Cover Gaskets on a New Beetle car?


Replace the valve cover gasket if the valve cover gaskets are leaking or if they're worn. The procedure is as follows:--
1) First of all let the motor cool down if the car was recently driven. Then remove the air intake boot.The air intake boot ios attached to the engine's throttle body.
2) Carefully disconnect the throttle cable , hoses and electrical connectors located on the upper intake manifold.
3) Then disconnect the hard pipe that is connected to the EGR (exhaust gas recirculation) valve.
4) The EGR valve is located beneath the upper intake manifold.
5) Then remove the bolts from both the upper intake manifold and the manifold support bracket.
6) Now the upper intake main fold and lower intake manifold both have got loose as you removed the nut.
7) After that remove the upper intake manifold from the lower intake manifold. Carefully place clean rags over the intake runners to prevent anything from falling into the intake system.
8) Then you will have to disconnect the crank case breather valve on the valve cover.
9) Then remove the bolts from the valve cover and remove the reinforcing straps.
10) Then remove the camshaft belt cover and the dust shield from the back of the camshaft sprocket.
11) Now carefully remove the valve cover. Properly clean the old gasket material with gasket remover.
12) You can install a new gasket in the reverse procedure of removal.


This will help. good luck.

on Mar 09, 2010 | Volkswagen Beetle Cars & Trucks

1 Answer

On a 2000 explorer 4.0 Soho do I have to remove the injectors to remove the lower intake


REMOVE UPER INTAKE 97 EXPLORER V6 4.0 - YouTube

? 12:22
https://www.youtube.com/watch?v=ugExJ0wkP8A
Jun 11, 2013 - Uploaded by Sum Guy
REMOVE UPER INTAKE 97 EXPLORER V6 4.0 ... I was told that all I have to do is remove the fan belt to get access to it ... FordExplorer 2000 intake manifold gasket upper lower P0174 by froggy - Duration: 36:54. by froggy 36,588 views ... Ford Explorer 4.0L SOHC Rough Idle P0171 P0174 Lean Codes ...

Putting the lower intake on my 1997 Ford Explorer 4.0 OHV ...

? 5:23
https://www.youtube.com/watch?v=qKE1vPxqPHs
Jun 27, 2010 - Uploaded by origionaldz
Putting the lower intake on my 1997 Ford Explorer 4.0 OHV sport .... I do have a 2000 5.0 ... @michaelheiland123654 To dothis job, you have to remove the alternator, unbolt the AC compressor, remove upper intake manifold, remove fuel rail,remove all injectors, ... Do you have the SOHC or OHV version?

1999 Ford Explorer 4.0L -need assistance on removing upper intake ...

www.automotiveforums.com > ... > Ford > Explorer ' Explorer Sport Trac
Sep 20, 2011 - 1999 Ford Explorer 4.0L -need assistance on removing upper intake ...Are you sure you have the OHV/pushrod engine and not the SOHC engine? ... Do youhave the upper intake manifold loose, you just are unable to ... the lower intake gasket, valve cover gaskets, Injector o-rings, plugs and wires. Thanks ...

How to replace upper intake manifold gaskets - Ford Explorer




Dec 09, 2015 | Cars & Trucks

1 Answer

Water leaking from rubber elbow on intake manifold passenger side of motor


It could be the intake gaskets, or it could be that the upper intake is starting to fail. Both are common problems. How fast are you losing coolant? If it's fast, then it may be the upper intake. Also, how many miles are on it, and has the upper intake been replaced before? It may be due for a new one.

Anyway, the procedure for doing the gaskets and for replacing the upper intake are exactly the same, except that if you replace the upper intake, you put on the new one instead of reinstalling the old one. I've done this with mkaake over a couple of days. There's a lot to remove and replace, but nothing that's especially hard to do. Have a service manual of some kind on hand, and do some serious research before you take it apart.

Parts you'll need:

1) Upper intake gasket set
2) Lower intake gasket set (make sure it's the new upgraded version, with metal inserts)
3) Plastic coolant elbow (it's under the alternator, and rarely comes off in one piece. It's also a dealer part, so if you're doing this on a Saturday and the dealer is closed... you get to wait until monday to put it back together - unless you get one ahead of time)
4) Fuel injector O-rings (might as well replace those while you've got them out anyway)
5) Carb/TB cleaner - several cans (you'll want to clean up the upper and lower intakes, and the TB while you've got them off)

That's all I can think of right now. I also don't know prices. Maybe someone else will have that info.

May 17, 2011 | 1996 Buick Riviera

1 Answer

Coolant leaking in and around the intake manifold as well as the under carriage of that same part I think. Outake? I know that the part that attaches to the manifold appears to be metal but the manifold...


The plastic piece is the upper intake manifold. The metal part is the lower intake manifold. Sometimes the gaskets go bad between the upper and lower intake manifolds. But usually the upper intake manifold is cracked and needs replaced.

Nov 11, 2010 | 1993 Buick Park Avenue

2 Answers

Need torque specs for 2000 chevy malibu 3.1 cyl heads & intake


(step 1 ) the torque specs for the heads are---1998 through 2001 are 37 foot lbs. ( step 2) rotate an additional 90-degrees (1/4 turn). intake manifold bolts ( lower ) step 1-- 62 in-lbs, step 2--115 in-lbs. intake manifold bolts/studs ( upper ) 18 ft-lbs. this is for the 3.1 v-6, have a good day!

Aug 14, 2010 | 2000 Chevrolet Malibu

2 Answers

Need to replace the intake manifold


3.8L Engine (most common) Upper Intake Manifold To Remove:
  1. Drain the cooling system.
  2. Remove or disconnect the following:
    • Negative battery cable.
    • Fuel injector sight shield.
    • Air cleaner intake duct.
    • Right spark plug wires from the ignition control module and reposition.
  3. Relieve the fuel pressure.
  4. Remove or disconnect the following:
    • Fuel rail assembly.
    • Brake booster hose from the vacuum source manifold in the upper intake manifold.
    • Exhaust Gas Recirculation Valve (EGR) wiring harness heat shield nut, bolt and the EGR heat shield.
    • Throttle body support bracket upper bolt.
  5. Disconnect the electrical connectors from the following:
    • EVAP purge solenoid
    • Throttle Position (T/P) sensor
    • Idle Air Control (IAC) valve
    • Manifold Absolute Pressure (MAP) sensor
    • Mass Air Flow (MAF) sensor
    • EVAP purge solenoid vacuum line from the throttle body.
    • Accelerator and the cruise control cables with the bracket from the throttle body.
  6. Remove or disconnect the following:
    • Upper intake manifold bolts and stud.
    • Clean the upper intake manifold bolt threads.
  7. Remove or disconnect the following:
    • Upper intake manifold by lifting the back of the intake and sliding the manifold forward from the throttle body support bracket.
    • Upper-to-lower intake manifold carrier gasket from the upper intake manifold.
  8. If the upper intake manifold is being replaced, remove the following:
    • Throttle body assembly.
    • Manifold Absolute Pressure (MAP) sensor.
    • Positive Crankcase Ventilation (PCV) valve.
    • Vacuum source manifold.
Upper intake manifold bolt torque sequence (3.8L engine) gm-03-38-530.gif

To Install:
  1. If the manifold was replaced, install or connect the following:
    • Vacuum source manifold.
    • Positive Crankcase Ventilation (PCV) valve.
    • Manifold Absolute Pressure (MAP) sensor.
    • Throttle body assembly.
    • Upper-to-lower intake manifold carrier gasket to the upper intake manifold.
  2. Carefully place the upper intake manifold onto the lower intake manifold. Ensure that the alignment pins in the upper intake manifold align with the holes in the lower intake manifold. NOTE: Apply thread lock compound, to the bolt threads before assembly.
  3. Install or connect the following:
    • Upper intake manifold. Tighten the upper intake manifold bolts in sequence to 89 in lbs (10 Nm)
    • Accelerator and the cruise control cables with the bracket to the throttle body.
    • EVAP purge solenoid vacuum line to the throttle body.
  4. Connect the electrical connectors to the following:
    • Mass Air Flow (MAF) sensor
    • Manifold Absolute Pressure (MAP) sensor
    • Idle Air Control (IAC) valve
    • Throttle Position (T/P) sensor
    • EVAP purge solenoid
  5. Install or connect the following:
    • Throttle body upper support bracket bolt. Tighten the bolt to 89 in lbs (10 Nm)
    • EGR valve wiring harness heat shield, nut and the bolt. Tighten the nut and the bolt to 89 in lbs (10 Nm)
    • Brake booster hose to the vacuum source manifold.
    • Fuel rail assembly.
    • Right spark plug wires.
    • Air cleaner intake duct.
    • Fuel injector sight shield.
  6. Connect the negative battery cable.
  7. Fill the cooling system.
  8. Inspect for fluid or vacuum leaks.
Lower Intake Manifold (W/O Supercharger) To Remove:
  1. Remove or disconnect the following:
    • Upper intake manifold.
    • Generator brace.
    • Drive belt tensioner with the mounting bracket and the heater water bypass inlet pipe.
    • Exhaust gas recirculation EGR outlet pipe bolt from the lower intake manifold.
    • Radiator inlet hose from the water outlet housing.
    • ECT sensor electrical connector.
    • Right upper engine mount strut bracket.
    • Generator brace bracket bolts.
    • Generator brace bracket.
    • Lower intake manifold bolts.
    • Lower intake manifold.
    • Lower intake manifold seals.
    • Lower intake manifold gaskets.
  2. If replacing the lower intake manifold, Remove or disconnect:
    • Water outlet housing bolt and stud
    • Water outlet housing
    • Gasket and the thermostat.
    • ECT sensor.
  3. Inspect the flatness of inlet flanges.
  4. Clean the intake manifold mating surfaces.
  5. Clean the intake manifold bolts and bolt holes of adhesive compound.
To Install:
  1. If removed, install the ECT sensor.
    • Tighten the ECT sensor to 18 ft. lbs. (25 Nm)
  2. If removed, install the thermostat, the gasket, and the water outlet housing.
  3. If removed, install the water outlet housing bolt and the stud.
    • Tighten the bolt and stud to 20 ft. lbs. (27 Nm)
  4. Install or connect the following:
    • Lower intake manifold gaskets. NOTE: Apply sealer GM P/N 12346286 (Canadian P/N 10953472) or equivalent to the ends of the intake manifold seals.
    • Lower intake manifold seals.
    • Lower intake manifold.
    • Lower intake manifold bolts.
    NOTE: Apply thread lock compound GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the two hidden bolts and ensure they are installed.
  5. Tighten the lower intake manifold bolts in sequence to 11 ft. lbs. (15 Nm) gmpc_v6_5.gif

  6. Install or connect the following:
    • Generator brace bracket.
    • Generator brace bracket bolts. Tighten the bolts to 37 ft. lbs. (50 Nm)
    • Right upper engine mount strut bracket.
    • ECT sensor electrical connector.
    • Radiator inlet hose to the water outlet housing.
    • EGR outlet pipe to the lower intake manifold.
    • EGR outlet pipe bolt to the lower intake manifold. Tighten the bolt to 21 ft. lbs. (29 Nm)
    • Drive belt tensioner.
    • Generator brace.
    • Upper intake manifold.
  7. Inspect for leaks.
Lower Intake Manifold (W/ Supercharger) To Remove:
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the supercharger.
  4. Remove the thermostat housing.
  5. Remove the EGR pipe at the intake manifold.
  6. Disconnect the electrical connection at the temperature sensor.
  7. Remove the intake manifold and gaskets.
NOTE: The coolant bypass tube will release from the intake manifold when the manifold is removed.
To Install:
  1. Clean the gasket sealing surfaces.
  2. Install the intake manifold gaskets.
  3. Align the coolant bypass tube with the opening in the intake manifold and install the manifold. Tighten the bolts to 11 lb ft (15 Nm).
  4. Install the electrical connector to the temperature sensor.
  5. Install the EGR pipe to the intake manifold.
  6. Install the thermostat housing.
  7. Install the supercharger.
  8. Fill the cooling system.
  9. Connect the negative battery cable.

Aug 05, 2010 | 1997 Pontiac Grand Prix

1 Answer

Replace lower intake gasket on 2001 infinite i30


1. Detach everything connected to the upper Intake manifold
2. Remove the upper Intake Manifold
3. Remove the fuel rail and injectors
4. Remove the IM
5. Replacement is the opposite.

Oct 08, 2009 | 2004 Infiniti I35

1 Answer

Intake manifold gasket / replace


3.8L Engine

NOTE The 3.8L (VIN K) non-supercharged engine uses a two-piece intake manifold consisting of an upper air plenum which mounts the throttle body and a lower intake manifold assembly which houses the fuel injectors. The 3.8L (VIN 1) supercharged engine uses a similar lower intake manifold. The supercharger serves as the upper manifold.
Lower Manifold

NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold. Remove the upper intake manifold to service the lower intake.
The 3.8L (VIN 1) supercharged engine uses a manifold similar to the 3.8L (VIN K), but the supercharger serves as the upper manifold.
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Remove the upper intake manifold using the procedure above.
  4. Remove the EGR outlet pipe from the intake manifold.
  5. Detach the engine coolant temperature sensor wiring harness from the sensor.
  6. Remove the lower intake manifold bolts and carefully lift off the manifold.

To install:


0900c15280269f1b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Lower intake manifold bolt torque sequence-3.8L (VIN K) engine
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces and between the lower manifold and the cylinder heads..
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Apply thread-locking compound to the bolt threads. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 11 ft. lbs. (15 Nm). Follow the toque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Upper Intake Manifold (Plenum)
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Tag for identification, then remove the right side spark plug wires.
  4. Disconnect the ignition wires from the fuel rail.
  5. Remove the fuel rail. Please see Section 5.
  6. Remove the cable bracket from the intake manifold.
  7. Remove the throttle body.


NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold.
  1. Remove the upper intake manifold bolts and carefully lift the upper intake manifold from the engine.



0900c15280269f1c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Upper intake manifold and bolt torque sequence-3.8L (VIN K) engine
To install:
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces.
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 89 inch lbs. (10 Nm). Follow the torque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Sep 11, 2009 | 1999 Buick Regal

Not finding what you are looking for?
1999 Pontiac Bonneville Logo

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...