Question about 2002 Jeep Liberty

1 Answer

I need to change the thermostat; but i cant see the bolt. a diagram can help

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 5,763 Answers

Heres a couple of pictures to help you locate the thermostat housing, if you follow the lower hose from the radiator to the motor you will find the thermostat housing on the block, remove the two bolts and off comes the housing and thermostat, hope this helps.I need to change the thermostat; but i cant see - 85e6022.gifda09e90.gif

Posted on Oct 24, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm trying to figure out how to change the


Hello victoriaulre,

Below I will provide step by step instructions and diagrams.

1. Drain radiator.
2. Remove the air cleaner duct for access radiator hose.
3. Reposition the hose clamp( circled in red) and then remove the radiator hose from the thermostat housing.See image below.
netvan_241.png
4. Remove thermostat housing bolt/stud.
netvan_242.png
5. Remove the thermostat housing and gasket.
6. Remove he thermostat.
7. Clean the gasket surface on the thermostat housing and the engine block.

To install, reverse above procedure.
Torque the thermostat housing bolt/stud to 18 ft.lbs.
Fill radiator and check for leaks.

I hope this helps.

Regards,

Jerry

Sep 12, 2011 | 2006 Pontiac G6

1 Answer

I need a diagram to replace the thermostat


I seriously doubt if you will find the diagram that you are asking for. The thermostat is very easy on most vehicles. Simply follow the upper radiator hose to where it connects to the engine. This would be the thermostat housing. The thermostat hosing is held on by 2 bolts. Remove the 2 bolts and remove the thermostat housing. The thermostat will be under the housing. Pull the old thermostst out and clean the gasket surfaces on both the engine and the thermostat housing. install the new thermostat and thermostat housing gasket and reinstall ithe thermostat and bolts. On some of the Dodge vehicles it is necessary to remove the alternator and/or power steering pump/ A/C compressor brackets to access the thermostat housing bolts.

Jan 22, 2011 | 1993 Dodge Dakota

1 Answer

I am trying to change the thermostat in my 1989 nissan maxima. im not sure if i put it in the top or bottom hose. please help. i need to find a diagram but am having trouble locating one.


Follow the upper radiator hose to the engine block. There should be a roundish metal housing at the end of it. Put a bowl underneath to catch any fluid and take off the bolts(try a 10mm socket or wrench) that hold the thermostat housing to the head. Then just pull out the thermostat and scrape off the old gasket. Put the new thermostat on spring-side toward engine, just like the old one. Make sure to use a new gasket! Then push the housing back over it and tighten the bolts. Add any anti-freeze necessary and your done!

Jan 16, 2011 | 1989 Nissan Maxima

1 Answer

Car is overheating, im trying to change the water pump and the thermostat. but i cant get the water pump off, and i cant find the thermostat


The thermostat is at the back of the engine, the upper radiator hose is connected to the thermostat housing, there are 3 10mm bolts holding it on. I'd check for maybe a missed bolt on the water pump, I know there is alot of bolts holding it on.

Jun 02, 2010 | 1998 Ford Taurus

2 Answers

Diagram of thermostat location on 2004 Chevrolet


2002 Chevrolet Cavalier 2.2L SFI OHV 4cyl

2.2L VIN 4

90e0bc0.jpg

Fig. Remove the thermostat outlet bolts and outlet

1314104.jpg

Fig. Remove the thermostat


2.2L VIN F

db08240.jpg
Fig. Remove the thermostat


Hope helps (remember rated this)

Feb 05, 2010 | 2004 Chevrolet Cavalier

1 Answer

Where is the thermostat located in the 199 venture and how difficult to change is there anywhere I can find a diagram


The thermostat is loacted in the thermostat housing under the throttle body on the intake manifold.

Here is the official GM method. Hope it helps. Also be sure to completely bleed the system of air.

  • Remove the air intake tube from the throttle body to air cleaner box.
  • Drain the coolant till level is under the thermostat level.
  • Remove the crossover exhaust pipe and radiator hose from the housing.
  • Remove the top bolt and loosen the bottom enough to wiggle the housing out.
  • Remove the thermostat housing and thermostat.
  • Clean matting surface.
Installation
  • Install thermostat and housing
  • Add RTV sealer to bolt threads
  • Tighten bolts to 18 lb ft.
  • and install everything else in revers
  • Re fill coolant and work air out of cooling system
  • Start the engine and inspect for any coolant leaks
Do not add radiator stop leak to coolant system, The rubber gasket on the thermostat will eventual stop the leak when it warms up and re tighten the thermostat housing bolts after the engine cools down.

Good luck and keep me posted.

Jan 06, 2010 | 1999 Chevrolet Venture

1 Answer

I have a 1995 ford escort lx 1.9 and need to know where the thermostadt is located and how difficult to change


It's fairly simple to change. Remove the water hose from the thermostat, remove the 2 bolts and lift away (may need a flat head screwdriver to pry away from thermostat housing). Below is the diagram for your thermostat. Best of luck.
Greg
1d2a7b6.gif

Oct 25, 2009 | 1995 Ford Escort

1 Answer

How do u change the thermostat housing on the f150?? its a 93 straight 6..buddy broke the housing changing the thermostat and cant get the housing off to change it


this simply requires removal of hose and both attatching bolts of the housing to the block...restart all bolts by hand until properly started

Sep 27, 2009 | 1993 Ford F150 SuperCab

2 Answers

Help changing thermostat 2002 chevy venture


THERMOSTAT REPLACEMENT

Removal Procedure
1.Remove the air cleaner and duct assembly.
2.Drain the coolant until the coolant level is below the thermostat. Refer to Draining and Filling Cooling System .
3.Remove the crossover exhaust pipe.
4.Remove the radiator hose from the thermostat housing
5.Remove the thermostat housing bolts and clean any sealer from the bolt threads.
6.Remove the thermostat housing and gasket.
7.Remove the thermostat.
8.Clean the mating surfaces.

Installation Procedure
1.Install the thermostat.
2.Install the thermostat housing and gasket.
3.Install RTV sealer, GM P/N 1052366 or the equivalent, to the thermostat housing bolt threads. .
4.Install he thermostat housing bolts.
Tighten
Tighten the bolts to 25 N.m (18 lb ft).
5.Install the radiator hose to the thermostat housing.
6.Install the crossover exhaust pipe
7.Install the air cleaner and duct assembly.
8.Fill the cooling system. Refer to Draining and Filling Cooling System .
9.Inspect the cooling system for leaks. Repair as necessary.


http://www.2carpros.com/forum/automotive_pictures/99387_Graphic2_59.jpg

http://www.2carpros.com/forum/automotive_pictures/99387_Graphic3_26.jpg

http://www.2carpros.com/forum/automotive_pictures/99387_Graphic4_13.jpg

Mar 30, 2009 | 2002 Chevrolet Venture Passanger

1 Answer

Need to change my thermostat on my 1999 Jeep Cherokee Sport 4WD


I do not know a link to a diagram, but I can certainly tell you how to find the thermostat! Looking at the front of the engine, there is a large water hose at the top of the motor that goes to the left, and attaches to the radiator. Not the radiator end, but the other end attaches to the thermostat cover. It has 2 bolts to take out and the little thing between that, and the motor about 2" around that kind of looks like a spinning top, is the thermostat. It is easy to change. Make sure you get ALL the old gasket off and that both bolts go through the new one, and you should be in business!

Dec 21, 2008 | 1999 Jeep Cherokee 4WD

Not finding what you are looking for?
2002 Jeep Liberty Logo

946 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...