- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
You'll need to remove the door panel from the inside of the door. Go to an auto parts store and ask them for a trim removal tool and a pry tool to help remove the window crank handle - tell the clerk what you want to do. Use the trim tool to unhook the catches around the outside of the door panel. Remember to unscrew the arm rest before you try to pull the panel off the door. Once you have that off, you will likely find that that the glass has slipped off of the track that the bottom of the glass rides on. It helps to have someone help you hold the glass as you lift it up and reset it on the track. Make sure that it is seated squarely on the window track and that it rides up and down smoothly before you put all the parts back together.
Remove the clips in the inside of the window handle,also clips on door handle.Look for any screws holding the door panel on, then take a screwdriver and pry the door panel away from the door. re install the window handle,and try rolling the window down. You will probably see what is stopping it.
If it looks like the window regulator is worn out, check the local junk yards for a replacement.
If its an electric system, chances are the window motor went out. Also another problem that could be causing it is a broken regulator as well. If you know enough about cars you can remove the door panel your self and take a look to see whats going on. Parts for this type of situation can be located in Autozone, Carquest, Napa, or Pep Boys. Now if it is a system where you use a handle to roll the window up and down then the linkage that attaches the regulator to the handle may be broken. Again you can remove the door panel, there should be only a couple of bolts and take a look. A word of caution when dealing with anything electrical always disconnect the battery to be on the safe side and aviod getting shocked or having one of the systems acuate while you are touching them.
Since you can get the door open, half the battle is already won. Yes, open the door, pull the interior door panel and take a look around. Watch inside with a flashlight (towards the rear of the door) as you roll the window down to see if you can see what it's snagged on.
after removing door handles,arm rests, etc.,roll down your window,the panel will only come off after the window is rolled down.push the top of the panel towards the window,there's a piece of trim connected to the top of the door panel that hooks to the top of the inner door
1, Disconnect the able from negative terminal of the battery. 2. Pry the courtesy light from the door trim and disconnect the wire connector.. 3. Remove all door trim panel retaining screws and door pull armrest assemblies. 4. Remove the door switch panel and the control switch panel and the control switch assembly. 5. On models with memory seats/mirrors, use small-flat bladed pry tool to remove and disconnect the wire. 6. Grasp the trim panel lift up and pull out to detach it from the door. Disconnect the inner door handle lock rod from the handle. Unplug any electrical connectors remaining and remove the door panel. 7. To install, connect the wire harness connectors and place the panel in position in the door. Press the trim panel down into place until the hooks are seated. 8. Install the armrest/door pulls, the courtesy light and the window switch' 9. Reconnect the battery
Also. You will need star pattern drivers to remove the window and motor from your door. If you have all the equipment it should only take you 1 hour.
Remove the door window regulator handle and then remove clip using a piece of cloth (Manual type only)
Remove the rear door inside handle housing.
Remove the mounting screws (3EA) from the trim fasteners and the door trim panel to pry off. Disconnect the connector.
Insert a trim panel remover between the trim fasteners and the door trim panel to pry off. Disconnect the connector.
Remove the door pull handle mounting bracket and door inside handle.