Question about 2005 Dodge Ram 2500 Truck

Open Question

2005 dodge ram 2500 diesel truck... when i put the truck in gear, (any gear) with the brakes pressed down the truck tries to take off on its own, kinda like idling high when trying to stop.. its the strangest thing!!! someone indicated it might be the torque converter engaging or not dis engaging, because it tries to take off... but why does it rev the rpm's as high as 1700 when doing this????????

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 66 Answers

SOURCE: 2006 dodge ram 2500 4x4 diesel replace brake pads front and back

Straight forward job. Remove wheels, remove 2 caliper bolts per wheel, check bolts,and bushings for wear/corrosion and lubricate, remove calipers, remove brake pads, push caliper pistons into calipers, replace anti-rattle clips, put new pads in, put caliper and bolts in, put wheels on. Start truck and press brake pedal several times to take up slack and you're done.

Posted on Jun 02, 2009

Ad
  • 83 Answers

SOURCE: 2006 Dodge Ram 2500 diesel truck----need inside fuse box diagram

If you are looking for the fuse box diagrams or any other diagrams for your Ram, check promanuals.net for a factory service manual for around 20 bucks or so. It's an invaluable tool for my Ram 2500.

Posted on Sep 26, 2009

  • 1 Answer

SOURCE: problem with hid on 2008 dodge ram 2500

Not too much amperage. HID lights use less amps. Duh. The circuit is showing a failure in the HID kit from not enough amps so it turns off. You need to add a resistor.

Posted on Dec 07, 2009

  • 217 Answers

SOURCE: what are the torque specs for the rear caliper

the caliper bolt torque is 22 ft. lbs. thanks and come again

Posted on Mar 25, 2010

tburtk
  • 158 Answers

SOURCE: 1995 DODGE RAM 2500 4WD ENGAGEMENT PROBLEM!!!

You have vacumn lines the run to your transfer case and then to the vacumn motor on the front axle. you need to check the lines and connections. If vacumn is working fine, then motor on front axle is bad.

Posted on May 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the belt diagram and rotation direction for a 2005 dodge ram 2500 5.9 turbo diesel.


moz-screenshot-8.pnghttp://www.dieseltruckresource.com/dev/help-installing-serpintine-belt-t183515.html?&highlight=fan+belt+diagram

scroll down to the 6th post

Sep 05, 2010 | 2005 Dodge Ram 2500 Truck

1 Answer

1999 dodge ram 2500 turbo diesel the trailer brakes won't work and I tried a different truck to make it was not the trailer any ideas?


We just had the same problem with our 99 2500 Turbo Diesel Ram. The problem ended up being the factory trailer cord recepticle near the hitch. When we unplugged the harness from the back side of the recepticle we found that the brake terminals had gotten hot and burned out. We replaced the recepticle (about $30 from Dodge) and our problem was solved.

Jul 15, 2010 | 1999 Dodge Ram 2500 4WD

1 Answer

How does a fan belt for a 2005 cummings diesel go diagram


Heres a belt diagram for a 2005 dodge ram 2500 series, with the5.9 diesel engine hope this helps.93aadb7.png

Apr 20, 2010 | 2005 Dodge Ram 2500 Truck

1 Answer

Dodge 2500 ram diesel no tail lights and my abs


replaced the IPM (the fuse box) it was shorted

Oct 25, 2009 | 2001 Dodge Ram 2500 Truck

1 Answer

2002 dodge diesel 2500 5 Speed....... Clutch will


if master cylinder and slave cylinder.is good and have brake fluid is in system and no leaks.problem is in the clutch and pressure plate.

Jun 10, 2009 | 2001 Dodge Ram 2500 Truck

1 Answer

2006 dodge ram 2500 4x4 diesel replace brake pads front and back


Straight forward job. Remove wheels, remove 2 caliper bolts per wheel, check bolts,and bushings for wear/corrosion and lubricate, remove calipers, remove brake pads, push caliper pistons into calipers, replace anti-rattle clips, put new pads in, put caliper and bolts in, put wheels on. Start truck and press brake pedal several times to take up slack and you're done.

Apr 25, 2009 | 2004 Dodge Ram 2500

1 Answer

Water pump replacement procedure 2005 2500 dodge with cummins diesel


take off old water pump. clean up area on the motor real good.do this by using a scrapper and cleaning slolvent. when thats all done put hi temp silicon on the block water pump and the put gasket on silicon. let dry for like five minutes. put in on torque bolts to specs.

Aug 22, 2008 | 2005 Dodge Ram 2500 Truck

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...