Question about 1987 Toyota 4Runner

1 Answer

Do I need to pull the manual transmision stilll attached to the motor when I pull it or can I leave the tranny in the truck?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,299 Answers

You can leave the tranny in the truck.

Posted on Oct 24, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2002 Passat wagon, with a1.8 l engine and a 5 speed automatic transmision. By mistake I drained the transmision. |How do do I refill the transmision so that I can take it to a shop to top it up...


Find the transmission filler tube under the hood. Get a funnel, and fill. Do not overfill, and use proper tranny fluid for your cars' specifications. Your user manual should have a capacities index, and the type of trans. fluid to use listed somewhere in the manual. Hope this helps.

Apr 02, 2010 | 2002 Volkswagen Passat

1 Answer

I just replaced a transmision on a l998 Chevy Blazer and when I put it in gear it barely moves what could be the problem. I filled it up with transmition fluid. Could it be the Torque Converter? Or could...


Proper way to fill tranny after instalation of a new one is to fill to fill line before starting motor. Once it is full, read the dipstick. It will say to check with motor running and either in neutral or park. Clean off the dip stick and take a reading with motor running and tranni in proper position. Keep filling and rechecking untill it reads full while running and tranni in proper position. Once completely filled should run fine if the kickdown cable, aka tv cable, is adjusted properly.

Feb 21, 2010 | 1998 Chevrolet Blazer

2 Answers

I need to change the oil pan. what is proceedure?


support front of vehicle, drain oil and return to oil recycling center (walmart) remove both (right and left) motor mounts and transmision linkage, transmision support bars( if needed for extra clearance ) unbolt oil pan. carefully lif engine from frame, taking care not to hit and break anything when the engine gets too close to your firewall. you should then be able to remove and replace oil pan. you'll need the bolt tightening pattern and torque specs for your vehicle. hope this helps

Oct 27, 2009 | 1998 Chevrolet S-10 Pickup

2 Answers

What do i need to do to convert my c-6 4x4 tranny into a 4x2 tranny


get a 4x2 tranny, and replace the 4x4 tranny and 4x4 transfer case with it, you will also need to remove your front drive shaft, that operates your front FWD, and replace the drive shaft for the rear axel.....

Find a good Salvage yard and see about trading parts to convert to 4x2

Sep 14, 2009 | 1981 Ford Bronco

2 Answers

Whats the best way to pull the engin


Disconnect all wire,remove both axle, shifter cable,cross member and pull right out.

Aug 03, 2009 | 2000 Dodge Neon

2 Answers

Find filter on transmission


IN   SIDE   THE TRANSMISION  PAN  

May 15, 2009 | 2002 Hyundai Santa Fe

2 Answers

Engine replacement


I thought all '87 FWD corolla's were 1.6l 4ac engines like mine. SOHC 2bbl Carb. Well in any case, I just did this with mine. You do have to drop the ball joint on the driverside to get the short shaft out, and then the tranny. the Passenger side cv shaft can stay put. You can then pull the engine out the top. Not enough clearance to pull just the engine or to pull both cause of the driverside manual tranny mount sticking out of the fender over the tranny. The easiest way is to drop both out of the bottom together, but the car needs to be high enough off the ground. Can't pull just the engine with a manual because of the shaft that goes in the clutch. if it were an auto sure, just unbolt the torque converter, sepereate the tranny, and pull the motor straight up. Watch out for the water pump pulley.

Mar 27, 2009 | 1987 Toyota Corolla 2 Door

1 Answer

Where do i check transmision fluid on a 1998 honda accord


left hand side of the motor near the fire wall closest to the windshield look for a yellow handle it will be short and may be in a difficult location to see put just poke your head in there and look...
if this is a standard tranny there will be no way to check othr than opening up the filler hole on your tranny


ps

Jan 15, 2009 | 1995 Honda Accord

1 Answer

94 geo prizm transmision


No u have to pull the tranny out Looking to help u Shaun

Nov 16, 2008 | 1994 Geo Prizm

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...