Question about 2001 Jeep Cherokee

2 Answers

Rear diff HI I own a 2001 jeep cherokee 4x4 and my question is we were taking apart the rear end to do the axel seals which one side was blown any way taking apart the diff and the bolt snapped off inside any ideas how to get the rest of it out. please something thanks

Posted by on

2 Answers

Hi FYI
I have a 2001 Jeep GC 4 x4 and had the axle seal at the wheel bearing start to leak. We use an axle puller and never opened the diff. Cheers Glen

Posted on Jun 16, 2008

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Head to a hardware store or a Car parts store and get yourself a set of "Easy-Outs".

The idea is that you drill out the bolt with a bit about half the daimeter of the bolt. Insert the easy-out into this hole. Now the easy-out has a very loose backwards thread that bites into this hole you drilled. And turn itall in the out direction. The stub of the bolt left may still need wd-40, hitting with a hammer , heating, or what ever to loosen it slightly. - Neil

Posted on Jun 13, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Only drives in 4x4 low take it out of 4x4 will not move


Check that it is actually getting into 2WD high and if the rear drive shaft is turning then check for an axle or diff problem in the rear end

Oct 25, 2013 | 1993 Jeep Grand Cherokee

2 Answers

Bad rear axle bearing and seal on a 2000 jeep grand


the bearing does not always have to be really bad for the seal to fail. Centrifugal force will throw axle grease outward where it gets on the rotor. That can make it feel like the rotor is out of round. If grease got on the brake pads I'd replace them and perhaps even the rotor. As far as the caliper being frozen, possible....check it out when you have it apart. You can have more than one shoe untied at the same time. Not always, but it can happen.
When replacing the seal make sure you put some grease on the lip before putting the axle back in. by doing that it won't fail from dry running before the diff lube reaches it.

May 15, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Where do I add fluid in the rear differential area in my 2001 Jeep Cherokee Sport?


theirs a bolt on the rear diff take it out and add make sure the bolts on the side not the bottom. the bottom bolt is only for draining

Apr 02, 2010 | 2001 Jeep Cherokee

1 Answer

The axle from a jeep 4x4 is broke , both axles, how do i take out the rest of the parts?


The front axel is a two piece assy. remove the 4wd
shift moter from the axel housing. Once the moter
and fork are off , remove outer axel.To remove inner
axel, remove differential cover and let it drain.
There is a C clip on the axel, remove it and work the
axel out through the axel tube.(if it is broken)
To remove the rear axel. Remove diff. cover and drain.
Remove the pinion lock nut(or spring clip) and slide
back pinion shaft. Remove retaining clip from axel
and remove axel. To remove broken piece I use to
use a length of an old whip antenna, to push it out.
If you can find a piece of heavy gauge wire to push
it out.(a plumbers snake may work)Also only have
one axel at a time out of either housing, this will
make it easier to reinstall the axels.
I hope I was of some help. Good luck.

Jan 30, 2010 | 1995 Jeep Grand Cherokee

1 Answer

How to replace my 1994 lincoln towncar rear axel seal


you need to pull the cover off the rear diff. remove the rear brake drums or rotors, remove the bolt that holds the pin in the rear end, remove the pin, remoce the c clips, pull the axles out. remove the seal. you can do this by using one ofthe axles to pry the seal out. install the new seal and reassemble. use rtv sealant to reseal rear diff and fill with about 3 - 3 1/2 qts gear lube-may take synthetic

May 23, 2009 | 1994 Lincoln Town Car

1 Answer

Rear Axel Seal Leaking, How do I pull the axel to repair?


You will need to remove the differential rear cover,drain fluid, remove wheel, brake drum, (rotor) . Unbolt center diff. pin, carefully remove (don't loose shims) push axle in remove lock keeper, then slide out axle, replace seal, put some grease on it, slide axle in reverse all to install.

May 22, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Rear axle seal replacement


Drain axel of Fluid, Roemve Diff Cover (Push IN on Axel to reseal at Wheel side) Remove KEEPERS From Insied END of axel then Pull OUT on WHEEL END of Axel. use Proper Seal removal tool to remove seal. Also Use PROPER Install tool for SEAL INSTALL Reverse Procedure to Install. In hopes this helps you Out.
Please RATE Me Also LoL Thank You.

Mar 24, 2009 | 1999 Ford F150 Regular Cab

1 Answer

LEAKING FRONT AXIL SEAL


take the wheel off , unbolt caliper and sling it out of the way with a bungi cord, take off the rotor, then you have too take the pumpkin cover off the axel diff in the front (drain fluid first) easy way to do that take out bottom and side bolts out then leave top 1 or 2 in but finger loose. pry cover off with a sturdy scrapper from side allowing fluid to leak out from bottom of cover. when fluid is done comeing out then take off cover. to take the axel out to replace the seal you have to push the axel inwards to remove the C- CLIP on the end of the axel shaft that slides into the inside of the pinion gear (use a extending magnet) keeps gear oil on your hands and from dropping it into the pumpkin housing. then all you have to do is slide the axel shaft out. then replace the seal .

Jul 01, 2008 | 1990 Jeep Wrangler

Not finding what you are looking for?
2001 Jeep Cherokee Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...