Question about 1996 Ford Explorer

1 Answer

Starter removal I know how to change a starter, however the problem I am having is that I have disconnected the starter and am now unable to get the starter to come out of the truck. It will not clear the front differential and oil pan and does not seem that it will come out from the top. 96 Explorer 4x4

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 87 Answers

If the oil filter is on the same side remove it slide starter all the way forward and out the front. some you actually have to remove the exhaust y-pipe

Posted on Jun 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to change out the starter on a 1979 Ford F350 but I do not know where the starter is or how to change it out. Thanks, Francie Green


the starter is located on the passenger side right under the manifold! all you have to do is disconnect the battery cables and then disconnect the starter wire and then remove the two bolts that run through the starter to the transmission.

Apr 17, 2011 | Ford F-350 Cars & Trucks

1 Answer

Unable to remove starter on a lincoln navigator 2000


Where are you stuck?
Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. NOTE: To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. Start the engine several times to check starter motor operation.
Let me know how you make out..

Feb 17, 2011 | Lincoln Navigator Cars & Trucks

1 Answer

Change out starter


Starter - 4 Cylinder 112139431
  1. Release hood latch and open hood.
  2. Disconnect and isolate the battery negative cable.
  3. Remove the air cleaner box.
  4. Remove the lower bolt.
  5. Remove the upper bolt and ground wire
Starter Removal - 4 Cylinder 112139432
  1. Remove starter.
  2. Disconnect solenoid wire connector from terminal
  3. Remove nut holding B+ wire to terminal.
  4. Disconnect solenoid and B+ wires from starter terminals.

Jan 01, 2011 | 2004 Dodge Stratus

1 Answer

Is it hard to change a starter on a 2008 Dodge Caliber?


NOT HARD YOU HAVE TO TURN OFF RADIO.DISCONNECT NEGATIVE BATTERY CABLE.REMOVE THE AIR INTAKE ASSEMBLY.REMOVE THE STARTER MOUNTING BOLTS.DISCONNECT THE THROTTLE BODY ELECTRICAL CONNECTOR. REMOVE THE THROTTLE BODY.PUSH THE STARTER UNDER THE INTAKE MANIFOLD.TIP THE NOSE OF THE STARTER TOWARD THE COOLING MODULE.PULL THE STARTER UP AND OUT.DISCONNECT THE STARTER WIRING.WHEN FINISH THE JOB.PUT EVERY THING BACK IN VISE VERSA.TORQE STARTER MOUNTING 40 FT LBS

Sep 12, 2010 | 2008 Dodge Caliber

1 Answer

Change starter 2005 chevy van express


first disconnect batt positive. jack vehicle up on passenger side. you can see starter at rear of engine. you may have to remove plastic around bellhousing to remove starter. There are two bolts holding starter in place.usually 15 mm socket. there is a small nut holding wire. 5/16 or 11/32 socket.. remove it. large nut usually 13mm socket. once removed just reverse procedure. leave comment if successful.

Mar 21, 2010 | 1999 Chevrolet C2500

2 Answers

Step by step instructions to change starter/94 Lexus LS400


Disconnect the battery.
Disconnect the wires from the starter.
Unbolt & remove the starter.
Bolt the new starter into place.
Connect the wires to the starter.
Connect the battery cables.

Dec 30, 2009 | 1994 Lexus LS 400

2 Answers

What is the easiest way to change the starter on 91 olds ciera 3.3 with Ac.


Hello. Here are the steps. Disconnect the - battery cable
Raise and support vehicle
Disconnect wiring at top of starter
Remove starter mounting bolts
Remove starter.

You can go to many auto parts stores these days and borrow the tools you need. good luck.

Nov 20, 2009 | 1991 Oldsmobile Cutlass Ciera

1 Answer

I need to know how to chang the starter and know and located


4.3 litre V6 ? first disconnect the battery before you start, then raise vehicle and place safely on approved weight rated jack stands, you will need a 14 mm or 15 mm socket wrench and an 8 mm socket or wrench to remove wire leads from starter and solenoid, remove starter by removing the two mounting bolts, reinstall in opposite form. starter is on paasenger side of motor sitting in the driver seat...

Sep 24, 2009 | 1999 GMC Jimmy

2 Answers

Starter removal steps


Jack the vehicle up and support with jack stands.Chock rear wheels.Disconnect positive battery lead.Disconnect all wires attached to starter motor solenoid.Remove starter supporting bolts.Pay attention to the position of the shims as you remove the bolts.Replace with working starter and attached electrical wires.Connect battery

Sep 16, 2009 | 1990 Chevrolet Lumina APV

1 Answer

2002 Toyota Corolla starter change out


Disconnect the battery.

Remove the lower plastic covers to aid in access.

Remove the battery cable lug from the starter and the signal wire.

Remove the two 14mm bolts holding the starter on and lower out the bottom.

*sometimes it helps the clearance to remove the oil filter.

Sep 14, 2009 | 2002 Toyota Corolla

Not finding what you are looking for?
1996 Ford Explorer Logo

254 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...