Question about 1995 Chevrolet Monte Carlo

1 Answer

How to change a starter - 1995 Chevrolet Monte Carlo

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 8,980 Answers

Please see my tip at http://www.fixya.com/cars/r5973094-starter_replace . These are generic instructions. Specific instructions from autozone.com are pasted below. Let me know if you have questions.

1995-96 VEHICLES

See Figure 13

  1. Disconnect the negative battery cable.
  2. Remove the upper mounting bracket above the radiator.
  3. Detach the electrical connections at the coolant fan, then remove the fan.
  4. Disconnect the upper and lower oil cooler pipes from the radiator.
  5. Raise and safely support the vehicle.
  6. Unfasten the retainers from the engine harness and position them away from the starter.
  7. Disconnect both lower oil cooler hoses from the radiator.
  8. Detach the starter electrical connections.
  9. Remove the upper flywheel inspection cover.
  10. Unfasten the mounting bolts/screws, then remove the starter and shims (if used) from the engine.

how to change a starter - 7624bd8.gif


Fig. Fig. 13: Starter motor mounting-1996 3.8L engine shown


To install:

  1. Position the starter and shims (if used) to the engine, then secure with the mounting bolts/screws. Tighten to 32 ft. lbs. (43 Nm).
  2. Attach the electrical connections to the starter. Tighten the solenoid battery terminal outside nut to 12 ft. lbs. (16 Nm). and the solenoid "S'' terminal inside nut to 22 inch lbs. (2.5 Nm).
  3. Position the upper inspection cover, then secure with the retainers to 89 inch lbs. (10 Nm).
  4. Attach both lower oil cooler hoses to the radiator.
  5. Fasten the engine wire harness and retainers.
  6. Carefully lower the vehicle.
  7. Attach the oil cooler pipes to the radiator.
  8. Install the coolant fan and attach the electrical connectors.
  9. Install the upper engine mounting bracket and tighten the bolt/screws to 32 ft. lbs. (43 Nm).
  10. Connect the negative battery cable, then check the engine oil level and add as necessary.

Posted on Oct 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Starter on my 91 ford ranger 4 wheel drive starts my pickup a couple time then it just spins have changed it 3 times now


Assuming the starter motor spins but doesn't engage to turn engine over to start you could have a bad starter drive which is part of the starter assembly or possibly damaged/missing teeth on flywheel ring gear. Depending on year and model vehicle, some starters you can replace just the starter drive otherwise you need to replace the whole starter. If you changed the starter look at the flywheel.

Sep 18, 2014 | Cars & Trucks

2 Answers

Blown starter fuse


Check the starter solenoid for a short to ground.

May 20, 2014 | 1996 Mitsubishi Galant

1 Answer

Fusible link from the starter


DO ME A FAVOR CHECK THE BATTERY.

Mar 29, 2014 | 2002 Dodge Grand Caravan

2 Answers

Starter makes a screeching noise sometimes just after the motor starts


Replace the starter before it ruins the flywheel. You have a worn out drive that applies to the flywheel. Flywheels are very very hard to change, in fact you can change 10 or 15 starters in the same time changing one flywheel

Jul 24, 2011 | 1997 Buick Century

2 Answers

Starter makes a grinding noise. and wont start changed starter and have the same problem. changed crank position senser and it worked for a while. changed it again but didnt fix the problem.


if the starter is making a grinding noise when you turn the key, it's one of several possiblites. 1. Bad Starter. 2. Bad flywheel. 3. You need starter shims that fit between the starter and the motor. Most starters will bolt straight up but sometimes the gears get too close so you need to shim them apart.

May 30, 2010 | GMC K1500 Cars & Trucks

1 Answer

Car will not start first thought it was the battery which turned out not to be true then found out it was the starter, starter has been replaced but car still will not start. It clicks twice and thats it...


did you change the solenoid with the starter or just the starter? if you changed both i'm not sure. if you just changed the starter and not the solenoid you should change the solenoid.

Mar 17, 2010 | 1999 Pontiac Sunfire

1 Answer

My starter kicks out before the car starts how can i tell if its the starter or celinoid


It's most likely the "bendix drive" in the starter kicking out. It's the part that engages the starter to the flywheel. Changing a starter without changing the solenoid is like having a slice of bread without any butter. Change them as a pair. Hope this helps.

Nov 27, 2009 | 1989 Oldsmobile Eighty Eight Royale

1 Answer

How to change starter selinoid


the starter selinoid is on the starter itself. normally a parts dealer will never seel you a starter selinoid individually but they will sell the starter with the selinoid. but you cant change the selinoid without changing the starter

Jul 09, 2009 | 1997 Chevrolet Camaro

1 Answer

I need to change my starter on a 1991 mercury sable


Starter are one of the easier mechanical engine parts to change.

1) DISCONNECT THE BATTERY.
2) Disconnect the electrical cable running to the solenoid on the starter.
3) Remove the two bolts holding the starter in place.
4) Pull the starter out.

To install another starter, do the above steps in reverse order in reverse.

Apr 04, 2009 | 1991 Mercury Sable

1 Answer

1998 Ford Windstar van will not start.


Ford starters have a solenoid that is a relay to the starter. I could not read the rest of the problem? Got changed ignition, starter and....

Jan 06, 2009 | 1998 Ford Windstar

Not finding what you are looking for?
1995 Chevrolet Monte Carlo Logo

380 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...