Question about 2005 Mazda Mazda5

Open Question

How to change a 2005 mazda 6 lowbeam headlight bulb

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 550 Answers

SOURCE: how do i change the headlight bulb in a 2005 sebring convertable

Lift up the hood, the bulbs are changed from the engine compartment
behind the lamp are connectors, pull it off, and the retainer that holds the bulb in
replace bulb
replace retainer
replace wire
close hood
usually takes longer to type than to do

Posted on Jul 14, 2008

Ad

Anonymous

  • 1 Answer

SOURCE: How do you replace the head light bulb on a 2004 Mazda 6?

it depends whether it is the o/s or n/s you either need to take the windscreen washer res out which is simply unscrew 2 bolts on top and lift it out of the way so you can gain acsess to the light unit then its pretty much plain sailing.or you need to remove the fuse box unit on the otherside

Posted on Sep 16, 2008

Anonymous

  • 1 Answer

SOURCE: Mazda 6 oil change

If DPF means Diesel Particulate Filter, no you don't need to change this cartridge. Somewhere near 120000Km you have to refill the additive tank with Eolys additive.

Posted on Jan 26, 2009

super_guy

  • 1986 Answers

SOURCE: 05 Mazda 6 I need to replace the headlights

Behind the head lamp you'll see a circular cap with some fins on it. Turn it counter clockwise and then it should come out exposing the back of the bulb. Then you will need to push in and up on an angle to release the metal spring clip that holds the bulb in place. Then you can disconnect the harness to the back of the bulb and then remove the bulb. Do not touch the glass of the bulb when putting in the new one as that will cause the bulb to catastrophically fail

Posted on Oct 28, 2009

Anonymous

  • 1 Answer

SOURCE: how do i change mazda 6 headlight bulb

This is difficult give yourself a good 30 mins. I have only found one way. Bonnet up - You will need a slim torch and a stubby x headed strewdriver to remove the plastic screws that hold on the wheel arch cover. Turn wheel away to give you more room. Once this is out of the way you can see the back of the light cluster, A twist and the back cover comes off. Remove the electrical connector, locate the retaining clip (much of this is by feel) when you take out the bulb make sure you note the way it came out as the replacement must go in the same way. Do not touch the bulb glass with your fingers, use paper or gloves. By feel, re-fasten the clip then reconnect the electrics. Reposition cover and twist back on, Refasten wheel arch cover. Make sure the cover goes inside the lip of the wheel arch otherwise spray from the wheel may get in., good luck

Posted on Dec 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mazda protege 2000 lowbeams dont work


check fuses . if they are good then you have a break in the wires or a bad switch. switch is no repairable. new one or one from the junk yard.

Mar 12, 2014 | 2000 Mazda Protege

1 Answer

How do I replace a headlight light bulb?


Open the hood & reach to the rear of the headlight, turn the retainig ring to release the bulb, pull it away from the headlight & unplug it. Dont touch the replacement bulb with your fingers.

Jan 10, 2011 | 2005 Mazda 6

1 Answer

My lowbeams don't come on for my 2005 Volkswagen Jetta. (Although the highbeams do come on.) I just discovered this tonight. Could this be a burned out fuse or other electrical problem?


Headlight

Removal & Installation

Bulb Replacement

To Remove:



  1. Release the spring clip and remove the protective cover from the rear of the
    bulb.
  2. Disconnect the electrical connector from the bulb.
  3. Remove the spring clip and remove the bulb from the headlight housing.


To Install:


CAUTION
Do not touch the glass portion of the new
bulb with bare hands.



  1. Insert the bulb in the housing.
  2. Secure the bulb with spring clip.
  3. Connect the electrical connector to the bulb.
  4. Install the protective cover on the headlight assembly.

Oct 29, 2010 | 2005 Volkswagen Jetta

1 Answer

How do i change the lowbeam headlight


There are two clips on the head light assy under the hood that you pull up and the head light comes out. you have to change the bulb in the head light because low and high beam lights are the same bulb.

Feb 07, 2010 | 2005 Chevrolet TrailBlazer

2 Answers

2005 Mazda 6 headlights keep going out


leaking headlamp lense or over voltage from the alternator

Jan 22, 2010 | 2005 Mazda 6

1 Answer

Lowbeams on Mpv went out. Highbeams ok, but


how are the headlight bulbs..i have seen many mechanics change all kinds of parts and turned out to be just both lamps coincidently went out at same time

Dec 10, 2009 | 2000 Mazda MPV

1 Answer

05 Mazda 6 I need to replace the headlights


Behind the head lamp you'll see a circular cap with some fins on it. Turn it counter clockwise and then it should come out exposing the back of the bulb. Then you will need to push in and up on an angle to release the metal spring clip that holds the bulb in place. Then you can disconnect the harness to the back of the bulb and then remove the bulb. Do not touch the glass of the bulb when putting in the new one as that will cause the bulb to catastrophically fail

Oct 28, 2009 | 2005 Mazda 6

1 Answer

Headlights lowbeams


have you tried changing the headlight switch

Aug 30, 2009 | 2005 Hyundai Sonata

1 Answer

Both low beam headlights stopped working at the


Could be the relay for the lowbeams is faulty, if your DRL's are your lowbeams, then your DRL Unit could be bad. Also did you blow a fuse cuz a random surge could blow the fuse

Aug 12, 2009 | 2005 Mazda 3

2 Answers

Need to change headlight on 2003 mazda rx 6


If it is the headlight itself. There may be a cover or shroud on the front of the engin bay. Remove that, may be a combination of clips and screws. If it does not cever the light area, it is even easier. There will probably be 3 screws or nuts, remover these and unplug the electrical to the light. From there you should just be able to pop the light out of place. If you are just replacing the bulbs. Where the power goes into the assembly, turn the clip, may be grey in color and pull out of the headlight assembly and replace the light bulb. But don't touch the new bulb the oils from your skin will damage the bulb.

Apr 22, 2009 | 1994 Mazda MX-6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

569 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...