Question about 1990 Chevrolet Corvette

1 Answer

Can someone tell me where the Electronic Spark Control Module is located on a 1990 corvette. Thanks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 5,332 Answers

In the distributor under the rotor.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Posted on Oct 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No start no fuel 1990 corvette has spark and new fuel pump


As someone who made this mistake, are all the wires reconnected under the fuel door? Check fuel pump fuse

Jul 11, 2014 | 1990 Chevrolet Corvette

1 Answer

Electronic spark control module


Hi, Spark is controlled by the computer. Where and when(timing). You can not change that. Each cylinder has 1 coil and spark plug. That module is built in to the computer. There are sensors around the engine that send info to the computer. Air, spark, timing, and fuel. When these things work properly the engine will run.

Feb 11, 2018 | Ford Cars & Trucks

2 Answers

1990 corvette idles rough sometimes. Sometimes it runs great when I start it up. then other times it wants to stall and I have to give it gas for a while but it still idles rough. It's either one way or...


Sounds like a clogged fuel injector.
Or worse one starting to go bad.
The problem with your car is the computer system readout is analog.
older models have a OBD-1 system and it makes finding the location of a bad injector a lot harder to find.
You could try a after market fuel additive called "sea-foam"
Most Wall-marts carry this product.
Give it a shot,I've done so myself on a VW VR-6 and talk about finicky fuel injectors!.
Worked really well for me,hope it does the same for you.
If I helped any please give me a vote.
Thanks,Gary

Dec 01, 2010 | 1990 Chevrolet Corvette

1 Answer

1990 buick lasabre with a 3.8 engine, cranks but no spark. No voltage to the primary side of coil. Code shows 22. Changed the trottle position sensor, crank position sensor and cam position sensor. Had the...


1. Monitor the 5v reference, Gray wire to the Throttle Position Sensor (TPS) with a Digital Volt Ohm Meter (DVOM) set to the MIN/MAX setting.

2. Monitor the TPS signal circuit, Blue wire with a DVOM. Voltage should range smoothly from approximately 0.44 to 5.0 volts as the throttle is opened.

3. Tap test the Electronic Control Module (ECM) and see if the codes come back or if the engine reacts.

possible causes wiring or Powertrain Control Module (PCM)

Oct 31, 2010 | 1990 Buick LeSabre

3 Answers

1990 vette stalls after 10-15 min. please help!!


38 lbs is not enough fuel pressure. replace the fuel pump

Mar 15, 2010 | 1990 Chevrolet Corvette

1 Answer

I just read the diagnostic codes on my 1990 corvette. I have two codes showing on the digital speedometer A Module 1 (CCM) Code C12 A Module 4 (ECM) Code H34 What do they mean? Thanks for your help!


Code 34 has to do with your MAP sensor I believe from what I am reading. I don't know a lot about corvettes but it says MAP sensor voltage low. The C12 code I see is a normal code set dealing with no reference pulses being received by control module. In other words with the engine not running. It has to do with No RPM reference pulse.

Sep 08, 2009 | 1990 Chevrolet Corvette

2 Answers

WONT START


It sounds as if the Ignition Control Module has failed. Remove the easiest spark plug you can reach. Reattach the plug wire and clamp the plug down to the valve cover or something that will make a good ground or electrical path. Have someone crank the engine while you watch to see if there is a spark across the electrodes. DON'T HOLD THE PLUG WHILE YOU DO THIS, IT WILL KNOCK YOU ON YOUR ****! If there is no spark chances are the ICM is bad. It's located on the left front behind the Pwr Steer Resevoir on the engine block. You might be able to remove it, 2 small screws, and have it checked out a a parts store. If you don't have any luck with this post your problem on corvetteforum.com. There are many there that will help.

Dec 06, 2008 | 1992 Chevrolet Corvette

Not finding what you are looking for?
1990 Chevrolet Corvette Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...