Question about 2000 Chevrolet Blazer

3 Answers

Brake lights my brake lights do not come on, yet the top light bar works , as do my signals and running lights all work .somebody told me it might be signal switch at the colomn anybody have this problem or can help me out would be much appreciated.

Posted by on

  • ovaltracker Jun 13, 2008

    thank you so much for your reply , i will definately give that a try and get back to ya. thanks again

  • Richy1983 Jun 15, 2008

    The Brake lights Don't work But the other lights work and so duse the Third light but not the brake lights And it wasnot the Plugins

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The hazard light switch contacts burnt up on my blazer. Try wiggling the hazard switch around as you have your foot on the brake to see it tahat's your problem.

Posted on Jun 23, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I turn my hazard lights on then off and then the brake lights work fine. Happens every so often.

Posted on Jun 29, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 239 Answers

Look under the drivers side rear under your truck there is a set of plug ins down there one of them has come loose. Its a common problem on that year I am pretty sure if you checked all the fused and they are all ok you must have had those wires in the back that I have mentioned try that and I think you will find your problem

Posted on Jun 10, 2008

  • bear001 Jun 13, 2008

    Ok sure Hopes that works, If not let me know and we can try another way, Take Care

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

!997 Ford Thuderbird brake lights and hazards do not work


Lets start at the beginning.
The turn signals and brake lights use different fuses but both go thru the turn signal switch and use the same bulbs.
Have you checked the fuses for each circuit and does each switch have power in and out ?

Feb 03, 2013 | 1997 Ford Thunderbird LX

1 Answer

My brakelights are both not working after changing the bulbs, changing brake pedal sensor, and checking all fuses. The running lights, parking lights, turn signals, hazard lights all work. Please give me...


Probably the blinker switch ..The brake light circuit runs through the blinker switch..Let somebody look and while you have the brakes applied move the switch around and see if the lights come on

Sep 09, 2011 | 2002 Ford Explorer Sport Trac

1 Answer

Turn signals wont work


An easy way to check the circuit for turn signals is to have somebody watch at the back then with the key on (you could have the motor running) put on the brakes. Do you have a brake light on both sides? If you do then manually go to the turn signal on then off (with the brake lights on). In other words you move the turn signal on the steering column to the on position then the off position. The person watching should see the tail lights change states (similar to a turn signal but slower) If they see the lights change then most likely your flasher unit is burned out and needs replaced. If there is no brake lights then the brake light fuse may be burned out. You can get instructions on flasher unit placement in the vehicle by the parts locator thru the autozone web site. Usually the flasher unit ( a small round device about 1 to 1 1/2 inches long) is right under the dash near or on the steering column

May 07, 2011 | 1995 Dodge Intrepid

1 Answer

I replaced light bulb and brake switch is there anything else that needs to be rp;acedto make brake light work


If you have already check fuses, and brake light's still don't work, it's going to be your turn signal switch, the brake light circit runs thought the brake light switch, if your car has a middle top brake light in back of rear window, most of the time that one will still work, and the turn signal will also work, but not the rear ones brake light's, when turn signal switch is bad, hope this was very helpful.

Aug 24, 2010 | 1997 Chevrolet Lumina

1 Answer

Tail lights on my 1995 for explorer work but brake lights wont come on top bar brake light works but bottom brake lights on tail light dont work what could be the problem


your brake lights also go through your turn signal switch,also known as the multifunction switch. You will have to remove the cover around the lower part of steering column to gain access to the switch.

Mar 27, 2010 | 1995 Ford Explorer

1 Answer

Brake lights dont work (95 Tahoe) but have signal and running lights and top brake light good fuses


Sounds like the turn signal switch. Top brake light is wired direct so it will always work.

Nov 14, 2009 | 1995 Chevrolet Tahoe

1 Answer

1999 GMC Suburban, K1500 4WD. Top brake light bar


third light is different circuit. saftey reason check fuses grounds wires

Oct 10, 2009 | 1999 GMC Suburban

1 Answer

Chevy s-10 Blaze brake lights put


do u have trailer plug,if so check wire harness connection,if not probe for voltage on brake light wires at back of truck for damaged wire in circuit.

Apr 12, 2009 | 1994 Chevrolet S-10 Blazer

3 Answers

No turn signals or brake lights on left and right but brake light on top


I agree. My brake light dont work. Only the third brake light does. The running lights work but when i apply the brakes the rear tails dont light up.
I currently have this issue along with the signals dont work unless I bang the top of the steering colum. The hazard switch doesnt work either. If the signals dont work it makes this very quick clicking sound on the passenger side. I checked the fuses and they are good. The bulbs still work. The brake switch works cause the third brake light goes on. And seeing as I am having a problem with signals.....GM says I have to replace the switch in the steerg colume. Its a little box about the size of a cigarette pack. If you take apart the panels off ( right behind the steering wheel, where the hazard switch is) ...that is where it is located. Its plugged into the signal lever. Hope this helpa....Good luck everyone with this issue.

Oct 17, 2008 | 2001 Chevrolet Blazer

6 Answers

No rear brake light / turn signals on 2001 Chevy Cavalier


The problem is the turn signal/headlight/hazard switch assembly on the steering column which the brake light wiring runs through. The part is easy to change and cost about $50 at most parts stores

Jul 05, 2008 | 2001 Chevrolet Cavalier

Not finding what you are looking for?
2000 Chevrolet Blazer Logo

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...