Question about 2000 Volvo S40

2 Answers

Headlight loose L H side headligh is loose can you tell me how to remove it thanks

Posted by on


2 Answers

Also when you get the light out you will require a new headlamp adjuster and these are £87 from volvo but on e-bay there £20

Posted on Jun 18, 2008

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Hi Lowgate, you need to remove the front bumper for a start. Then the headlamp can easily be removed by removing the 4 10mm bolts that secure it.

Posted on Jun 10, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My headlighs work but not running lights

Working headlights with no running lights usually means a bad headlight switch. They are not available new, try a junkyard or ebay... good luck... Chris

Jun 11, 2014 | 1994 Mercury Capri

1 Answer

Villager 2002 driver side headlights are sporadic

Normally the head lamp relays are placed within the dash and as close as possible to the headdlights as the high ampere required means that the wires must also be of short length to reduce loss or it might need large core wires.
So check the main relay box here within the engine room and use a multimeter to see if the cluster switch triggeres the relay.

Nov 21, 2011 | Cars & Trucks

1 Answer

I have a 2002 mitsubishi lancer oz rally edition and need to remove the headligh do i do this

In some vehicles you have to remove the headlight assembly and other parts to access the headlight itself, but in the Lancer you do not need to mess with any other car parts except those on the assembly. The assembly is a composite system, meaning if the low or high beam lights fail you can replace it without having to replace the entire assembly.

Dec 14, 2010 | Mitsubishi Lancer Cars & Trucks

1 Answer

Horn quit, can not locate to see if loose wire, 1997 cav cont

if i remember it behind and below the right headligh you should be able to trace the wire comming out of the harness just past the center latch

Dec 07, 2009 | 1997 Chevrolet Cavalier

1 Answer

Loose ground wire on headlight

You may need to pick up a new plug and some **** conecters and replace the plug to the headlight.Remove the old plug from the light ,cut off the wires one at a time and reconnect it to the coresponding wire on the old plug.

Oct 22, 2009 | 1998 Mitsubishi Galant

3 Answers

I need help troubleshooting the headlighs. All

next would be to check the hi-lo beam switch, play with the lever and see if you can get them to flicker, if so, replace the hi-lo beam switch (combination switch)

Sep 25, 2009 | 2000 Chevrolet Cavalier

1 Answer

Headlighs very dim

dont change bulds check battery and alternator first at oreyllys or autozone they do it for free same problem with my 02 jetta light were dimming replace battery it still was doing that it ended up being the alternator. in my case my car almost died becauce los of power alternator was sucking all power from battery. in your case did you check the cables on your headlights make sure they are not loose.

Sep 24, 2009 | 2003 Kia Sedona

1 Answer

Removal of Front Grill?

See this post:

May 30, 2009 | 2003 Toyota Highlander

2 Answers

How to replace headlight bulbs 1999 chevy malibu

Thanks Pierre!

Merci beaucoup!

Everything worked as mentionned. Be carefull with the plastic in the winter. Make sure to use a flat screw driver and get it close to the slider and not on the edge. I cracked one of the tongues. Those L shaped slots are under the plastic cover with the two big plastic plugs that you also remove with the flat screw driver

Pierre Godin, Boissevain Manitoba.

Oct 19, 2008 | 1999 Chevrolet Malibu

Not finding what you are looking for?
2000 Volvo S40 Logo

252 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides