Question about 1990 Toyota Camry

2 Answers

Elecrical recently the brake lights and plate lights in the back and 2 lights in the front of my car stay on, there permently ON! before this happened the center brake light stay on, so i didnt use it. but now there all on. any help will be welcomed. thanks: Jonathan

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check the wires were you radio gose make sure that they are ran right

Posted on Oct 12, 2008

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 45 Answers

Have you checked your brake pads to make sure there not worn down?

Posted on Jun 05, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Brake lights wont turn off when brakes are disengaged. is there a switch in which could be bad on it?

there is a brake light switch located at the top of your brake, take connector off and adjust by turning1/4 at a time, reconnect and check if light goes off and on. Might have to do this a couple of times. If light continues to stay on check the play in your brake pedal and adjust accordingly . If still on, remove and replace brake light switch

Jul 02, 2014 | 1999 Honda Accord

1 Answer

2004 grand am brake lights stay on all the time

Th first thing I would do is put one of the old tail lenses back into the car and see if everything is back to normal. If it is there is a problem with the new lenses you installed.

Led lights are very sensitive to proper power and ground. Bad grounds can make all kinds of weird things happen.

Jan 07, 2014 | 2004 Pontiac Grand Am

2 Answers

I recently had my truck--a 2006 GMC Canyon inspected for brakes because there was a squealing noise occasionally when I applied brakes. I had it inspected and the technicians said that I should have my...

hi sounds like good advice with out your rear brakes working properly all the load will be transfered to the front brakes causing uneven braking and in wet or slippery conditions front wheels will start locking up causing lose of control

Sep 13, 2011 | 2006 GMC Canyon

1 Answer

Problems 1. My brake lights stays on while driving without hitting on the breaks, 2. Car wont switch off after removing the key until I let go of the brakes then the car switches off. 3 Everytime I hit...

Hi, has someone recently installed something in the car or otherwise messed with the wiring? If not, is your ABS light on? If not either, I would say your hazard switch has gone bad.

Aug 29, 2011 | 2001 Ford Focus

2 Answers

Loud grinding in front driverside brake when applied, the pads are only half worn and I can't feel any significant grooves in the roter

do u only hear the noise when braking? those vans r prone to wheel bearing failure. the noise will always be there and will get loude with speed. the other thing it could be is the backing plate behind the rotor. all u have to do is gently push/pull it away from the rotor.generally if the wheel bearing has failed and the van has ABS the abs warning lamp will come on from time to time the eventually stay lit permently.

Jan 20, 2010 | 2003 Pontiac Montana

2 Answers

97 camaro turn signals fail to work

sounds like two problems. the front turn signals operate through the drl module. It's behind the radio. if you cut and splice the dk. blue to dk. blue w/ white, lt. blue to lt. blue w/ white on the black connector it will bypass the drl but all other functions will work. some say to disconnect the blue connector to bypass however this will discontinue other features, e-brake indicator, rear hatch button, ect. As for the rear light, i would check the rear lamp harness connector behind the interior plastic drivers side for power on the right signal feed and the splice ground.

Mar 21, 2009 | 1997 Chevrolet Camaro

1 Answer

Abs and brake light stay on continously

Could be one of the speed sensors on the front wheels. I believe the sensor comes with the wheel bearing assembly.

Mar 02, 2009 | 2001 Dodge Ram 1500 Truck 2WD

Not finding what you are looking for?
1990 Toyota Camry Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

74192 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7194 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides