a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US. click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
The valve cover gasket is probably one of the easiest repairs to make. Curious as to what your question actually is? Meaning, do you need to know what is required such as gasket's, sealants and tools, or maybe just the Torque spec's for tightening the bolts back on the covers...
if it is a 3.8liter engine generally about and hour there is 4 10mm bolts in the front valve cover and the rear you may have it remove the spark plug wires and coilpack/ignition controll module bracket.
The valve cover gaskets needs to be replaced, you can try to tighten up the valve cover bolts if it has gone loose. But that's may just slow the leak, so replacing the valve cover gasket would be the best thing to do, Auto Zone carries the gasket you need and can give you the step by step instructions to get the job done with common tools. Good luck and keep me posted, be glad to answer any more questions you may have.
Are you sure the Valve Cover and not just the Valve cover gasket??
Any ways go to Auto Zone and pick up the Valve cover gasket, RTV Silicone selant, Gasket Scraper, and a can of Brake parts cleaner spray.
Disconnect the battery cable from the negative battery terminal, Remove the items which are in your way: Pull the spark plug wires off the spark plugs and remove them from their brackets, remove the PCV hoses, and remove the throttle cable from its brackets and position it out of the way. Loosen the fasteners in this order, I believe there are 11 bolts holding the Valve cover down. Remove one bolt and count to the next 5th bolt and remove it and count to the next 5th bolt and remove it, do this till all the bolts have been removed on a circular pattern. Carefully remove the valve cover from the engine head. If your just going to replace the Valve cover gasket, Remove the gasket from the valve cover. Thoroughly clean the mating surfaces of the valve cover and the engine head. Use a gasket scraper to remove all traces of old gasket, and then use the Brake parts cleaner to clean any remaining oil from the surfaces. If you bought a new Valve cover, Apply RTV silicone sealant to the gasket and engine head around the cutout areas of the valve cover. Note you still have to clean the heads on the engine. Lay the new gasket in the groove in the valve cover. Reinstall the valve cover with its new gasket on the engine head. Tighten the bolts in the same order you removed it in. Do Not Over Tighten the Bolts that hold the Valve Cover down, you'll crush the new gasket and will get an oil leak. Note: If the valve cover does not come off the engine head easily, use a block of wood and a hammer to bump it in an attempt to jar it loose. If absolutely necessary, you may slip a flexible putty knife between the head and the cover to break the seal. If you purchased a valve cover gasket kit, don't forget to replace the small rectangular gasket and the spark plug seals as well while you have the valve cover off the car. You may buy some Brake cleaner to clean off all the oil which has leaked all over the engine. DO NOT attempt to pry the cover off the head using a screwdriver or chisel. Be very careful not to introduce foreign matter into the engine. If you get anything (dirt, metal shavings, bits of old gasket) into the engine. DO NOT over-tighten the valve cover fasteners. On the engine, the fasteners need only 17 to 34 in-lbs of torque. Your A/C system has a leak in it. all system has a slow leak and common, You can get a re-charge kit at Auto Zone to save some money, but if your A/C needs charging again in 2 weeks or less then there is a larger leak due to a bad seal and is cheaper to have a A/C shop locate the leak and replace the seal that has gone bad. Good luck and hope this help. keep me posted, be glad to help.
The first step is to remove all the parts that are in the way of you being able to remove the valve covers. (Ex.: air intake, loose wires etc.) Then you will need to remove your valve covers (using basic tools) and be very careful to not let anything get on your lifters, which your valve covers protect. Once you have the valve covers off compare the new gaskets to make sure they are the right size. Then remove the old gasket and replace with the new one using a high temp gasket sealant (available at any auto parts store) to attach the gasket to the valve covers. Then tighten down snug and check for leaks after replaced.
In this case this is serious work and you should contact a local VW dealership or mechanic and have them do this work for you to insure a job well done. If you simply mean your Valve cover, then this is no big deal and can be done by taking out the 4 screws found at the corners of the valve cover and then simply lifting the cover free and replacing it with a new one/tightening the screws back down.