Question about 2005 Hyundai Sonata

1 Answer

Need instructions on installing automatic antenna

If you could give me an exploded picture and instructions, i would really appreciate it. This is for my mom's vehicle.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 56 Answers

What kind of instruction you need

Posted on Jun 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Nissan troubleshooting


First check fuses, then check wiring to the antenna then the motor itself.

Jan 01, 2014 | Cars & Trucks

1 Answer

I want to change the automatic transmission filter. is this an internal filter? is it possible to get an exploded view of my cd4e transmission?


The transmission oil filter is inside the oil pan of the transmission. You will have to remove the oil pan (use a suitable container under it to catch the oil when it comes out) to change it. A Haynes manual has good instructions and pictures for this job.

An exploded view of the transmission may be difficult to find. I found this URL: http://www.gearheadtrans.com/images/fordtech/Cd4eev_blowup.jpg Unfortunately, I was unable to find a key listing the various parts.

Aug 15, 2010 | 1998 Ford Contour

1 Answer

Rebuilding the front


The best thing you can do, that will make everything you will need available to you, is to buy a Chilton or Motor's manual. They have every nut, bolt, wire etc. They also give instructions on how to remove and install difficult parts.

Aug 28, 2009 | 1997 Toyota Corolla

1 Answer

Antenna mast broken


    Give these instructions a shot. Might be too generic but might be enough to get you going. Removing Original Antenna
  1. Step 1 Activate the antenna switch to the up position.
  2. Step 2 Using the wrench or needle-nose pliers, loosen and remove the original retaining nut on the base of the antenna mast.
  3. Step 3 Gain access to the underside of the area where the antenna is located.
  4. Step 4 Remove the bracket or brace that is below the hole and holding the antenna in place.
  5. Step 5 Remove the mast.
  6. Step 6 Find the motor that controls the antenna mast. Generally, power antennas will have a constant 12-volt lead and a ground lead. The ground lead will be grounded to the panel next to the motor.
  7. Step 7 Remove the ground lead from the panel.
  8. Step 8 Pull out the antenna coaxial cable.
  9. Step 9 Unplug the coaxial from the extension coaxial cable.
  10. Step 10 Remove the original antenna coaxial cable. Note the route the cable follows.
    Installing the New Power Antenna
  11. Step 1 Inspect the fender area where the antenna mast will be mounted for rust.
  12. Step 2 Clean the area before installing the new antenna.
  13. Step 3 Plug the new antenna coaxial cable to the extension coaxial cable. (On some General Motors and Ford cars you may need an adapter to mate the 2 cables together. Car audio retail stores sell such an adapter.)
  14. Step 4 Plug the new antenna's coaxial cable into the radio's chassis antenna jack if there is no extension coaxial cable. Tie or tape the string you put on the extension cable to the new antenna coaxial cable. This assures that the 2 cables stay together as you route them to the antenna mount in the fender.
  15. Step 5 Connect the power lead of the antenna to the power antenna lead on the radio.
  16. Step 6 Connect the 12-volt constant lead to the antenna to a 12-volt source or to the ignition switch.
  17. Step 7 Direct the new antenna cable via the same route followed by the original antenna cable on up to the hole in the fender in which the mast will be mounted.
  18. Step 8 Ground the ground lead from the motor to a clean metal surface on the metal panel near the mount.
  19. Step 9 Insert the mast into the hole. Face the serrated side of the plastic cable on the bottom of the mast toward the motor side. The plastic cable can be inserted freely to about 12 inches and will stop.
  20. Step 10 Turn on antenna switch to down position until the plastic cable goes down and catches into the gear mechanism of the drum housing. If the plastic cable does not gear into the mechanism, twist the cable slightly until the cable contacts into the gear mechanism while the motor is in operation.
  21. Step 11 Stop the motor after the cable goes into the housing 12 to 25 inches.
  22. Step 12 Secure the bracket or strap to the bottom of the antenna mast and to the metal fender.
  23. Step 13 Replace the retainer nut to the base of the antenna mast and secure tightly.
  24. Step 14 Replace the panel that covers the antenna mount area.

May 13, 2009 | 1993 Chevrolet Corvette

1 Answer

My son recently bought a 3000GT SL but, the sunroof regulator assembly had been removed and disassembled. I have a box of parts, with definetly some screws missing but, I can only partially figure out how...


I may have a blow up in my service manual. If you haven't gotten it together, email me at OneRide2869@yahoo.com and I'll scan and email you the exploded diagram and instructions if my manual has them. BTW, an eBay seller, sphear_media, has 3000GT manuals on CD for around $10. You should get one. Trust me, you are gonna need it. I know, I own a 91 3000GT.

Apr 18, 2009 | 1995 Mitsubishi 3000GT

1 Answer

2002 Honda Civic Front Brake Pad Change


autozone.com has the best available information that is at no charge. They give you step by step instrucions and pictures with exploded views. Once you do the brakes a time or two it will be a snap. At the site simply add your vehicle and go to vehicle repair guides. Hope this helps.

Mar 07, 2009 | 2002 Honda Civic

1 Answer

1989 oldsmobile cutlass ciera 3.3L V6 power antenna broken


You need to access from outside the vehicle. You have to remove the shroud that is inside of the wheel well. It is not a very easy task I hope this helps.

Feb 04, 2009 | 1989 Oldsmobile Cutlass Ciera

1 Answer

Replacing a heater core


YOU DO NOT NEED TO REMOVE THE DASH BOARD. IT WILL BE BEHIND THE GLOVE BOX. LOOK UNDERNEATH THE DASH AND YOU WILL NEED TO REMOVE A PANEL TO GAIN ACCESS TO THE HEATER CORE. THE PANEL WILL BE ABOVE THE PASSENGERS FEET ON THE FIREWALL.

Jan 24, 2009 | 1991 Chevrolet Cavalier

1 Answer

Help to Replace Driver AND Passenger Exterior Mirrors 02 Impala


I used google to do a search for this and typed in "instructions replace side mirror". There is a guide on e-bay that pops right up and it gives you pretty detailed instructions. They are not vehicle specific but should give you all the information that you need. The web page says How to replace a broken side mirror on your car-associated content. I hope this helps, it looked like it had plenty of great information.

Jan 12, 2009 | 2002 Chevrolet Impala

1 Answer

How do I replace my timing belt? Just hit 80,000 miles HeLp!!!


the easiest thing to do is to go to your local parts store and buy a hanes repair manual. they have all the instructions and pictures

Oct 28, 2008 | 1999 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...