Question about 2000 Hyundai Accent

1 Answer

Computer codes I keep getting a 1402 code on my 2000 Hyundai accent and have no idea what it is

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,665 Answers

P1402 - dm-tl air pump motor is shorted or disconnected.

2000 model year accent is equipped with a new enhanced evaporative emission system. this new system is capable of measuring leaks as small as 0.020" diameter. the new system pressurizesthe evaporative emission system with a diagnostic module for tank leakage (dm-tl), while the previous model's system appliedengine vacuum through the purge valve to detect system leaks.

service information
vehicles that have the check engine light illuminated and have dtc p1401, p1402 and p1403 stored in the ecm should have their electrical systems diagnosed related to the appropriate dtc. these codes are not related in any way to an evaporative emission system leak. the conditions that set the diagnostic codes areas follows:
p1401 - dm-tl air pump motor current draw is higher or lower than expected (normal = 17-36 ma).
p1402 - dm-tl air pump motor is shorted or disconnected.
p1403 - dm-tl changeover valve is shorted or disconnected

perform the suggested repair
1. inspect for water in the dmtl by removing the 90° air inlet elbow and looking into the air chamber. if water or corrosion is present, replace the dm-tl p/n 31440-25500; air filterp/n 31453-25500; and pipe assembly p/n 31454-25500if corrosion is in the pipe. see detailed instructions on page3 for air filter replacement.
2. inspect for underbody coating sprayed into connector m52 at dm-tl. if underbody coating is present on the male or female connector, spray with electrical contact cleaner to remove the undercoating.

air filter (dm-tl) replacement instructions

  1. disconnect the 90° elbow from the top of the dmtl and insert a clean rag into either the elbow or thedmtl inlet connector.
  2. disconnect the dmtl electrical connector.
    1. disconnect the 2 hoses at the front of the canister (caution: silicone hoses tear/puncture easily).
    2. remove canister assembly and dm-tl as a unit (3 mounting nuts).
    3. disconnect the 2 hoses from the metal transfer pipes.
    4. remove the canister, air filter, and metal tube assembly from the canister protector by removing the 3 mounting nuts.
    5. disconnect the hose at the air filter.
    6. remove the air filter mounting nut and remove the air filter.
    7. install a new air filter.
    8. reassemble in reverse order.

Posted on Jun 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I change or test DM-TL?


code p 1402 refers to fuel tank leakage diagnostic module--motor malfunction===causes --fuel tank leakage motor diagnostic module motor
code p 1403 refers to the fuel tank diagnostic module ---valve malfunction
go to a service dealer and have the unit tested
it is possible that by replacing or cleaning the valve section , the problem will be fixed

Mar 31, 2016 | 2002 Hyundai Accent

1 Answer

Can or how do you test an oxygen sensor 2000 Hyundai Accent to find out if it is working properly? I keep getting error code P123. I have changed the oxygen sensor, but still keep getting the same err


There are two oxygen sensors. Change the other one. Make sure you are installing the correct sensor in the correct location. One is before the cat the other is after the cat. (upstream and downstream)

Apr 23, 2012 | 2000 Hyundai Accent

1 Answer

Looking at a 2000 hyundia accent but has a check engine light code of po447 is this a big problem


Research revealed no data availabe for code P0447 - doesn't exist for Hyundai Accent.

There are codes P0446 and P0445, but nothing with P0447.

Feb 06, 2011 | Hyundai Motor 1998 Accent

1 Answer

I have a 2000 Hyundai Accent, the check engine light came on after getting gas. The car is running fine.


More then likely it's going to be an evap code, check your gas cap make sure it's on right, also go by any auto parts or autozone where they can pull codes for free, and get back with us here at FixYa so we can help you diag. your trouble code.

Jun 29, 2010 | 2000 Hyundai Accent

1 Answer

2001 hyundai w/ engine light on scammer code 1402 what is it


What you can try first is disconnecting your battery cables(positive an negative).. What that does is reset your comuter..then re attach the cables and start the car to see if light comes back on.

Aug 14, 2009 | 2000 Hyundai Accent

1 Answer

Tranny; Reverse works but no drive at all.


this is a lack of EGR flow related code, it has no affect on the trans operation, the problem u have is that the forward clutch has failed, to repair this the transaxle must be overhauled.

May 21, 2009 | 2000 Hyundai Accent

1 Answer

The abs light on my 2000 hundai accent keep going off and on


the abs light comes on whenever the system detects a fault , when that fault no-longer is there the light will turn off , you should have a code set in your cars computers history . a competant mechanic should be able to get those codes for you to determine where to start diagnosing your abs Light issue .

Feb 06, 2009 | 2000 Hyundai Accent

1 Answer

2000 Hyundai Accent


00-30-001 2000 ACCENT DMTL DIAGNOSIS: DTC CODES P1401, P1402 AND P1403

p1402 - dm-tl air pump motor is shorted or disconnected.

2000 model year accent is equipped with a new enhanced evaporative emission system. this new system is capable of measuring leaks as small as 0.020" diameter. the new system pressurizesthe evaporative emission system with a diagnostic module for tank leakage (dm-tl), while the previous model's system appliedengine vacuum through the purge valve to detect system leaks.

service information
vehicles that have the check engine light illuminated and have dtc p1401, p1402 and p1403 stored in the ecm should have their electrical systems diagnosed related to the appropriate dtc. these codes are not related in any way to an evaporative emission system leak. the conditions that set the diagnostic codes areas follows:
p1401 - dm-tl air pump motor current draw is higher or lower than expected (normal = 17-36 ma).
p1402 - dm-tl air pump motor is shorted or disconnected.
p1403 - dm-tl changeover valve is shorted or disconnected

Jun 04, 2008 | 2000 Hyundai Accent

Not finding what you are looking for?
2000 Hyundai Accent Logo

1,026 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...