Question about 2003 Ford F250 Super Duty Crew Cab

1 Answer

On the 4x4 front axel whats the procedure to remove upper & lower ball joints. now ive got the hub out both up & low joints free but because of the axel yoke wont go toward the wheel ? how do proceed

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 266 Answers

THE AXLE HAS TO COME OUT OF SPINDLE USE A PRY BAR BEHIND THE AXLE AND PRY IT OUT OF THE SPINDLE IF THIS IS A VACCUM OPERATED SPINDLE THE SEAL WILL (HAS TO ) COME OUT

Posted on Oct 17, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the front left axle shaft on a chevy 2007


remove the axle nut first, always took the upper ball joint loose just take the nut off apply some upwards pressure and hit spindle with hammer and it will allow you to move the hub and all out enough to remove axle. the upper ball joint nut has to come off
and seperate the ball joint from the steering knuckle
then plenty of room. good-day ! then just slide axel out,or pry between axel and ****** to pop it loose, it has a locking clip on transmission side. when putting back in make sure axel is locked in ******. and do not forget to torque axel nut when done.

Aug 05, 2011 | 2000 Chevrolet Silverado

2 Answers

What do i need to take apart to remove the drivers side front drive axel to replace the universal joint at the hub? could the axel slide threw the hole for the axel berring assembly or do you need to take...


Have not done this on your truck but book says just the upper ball joint needs separated. See procedure below from autozone.com. Please let me know if you have questions.
  1. Remove or disconnect the following:

    Front wheels (left side should be sufficient in your case) Front hub cotter pin, retainer and nut (axle nut)
  2. Using a floor hydraulic jack, support the lower suspension arm.

    Upper ball joint cotter pin and castle nut Knuckle from the front suspension upper arm
  3. Lower the lower suspension arm and steering knuckle slightly to facilitate easier halfshaft removal.
  4. Remove the 2 disc caliper mounting bolts, then lift the front disc caliper off of the front disc brake caliper anchor plate and position aside. Do not allow the caliper to hang by the brake hose; suspend it from the vehicle's frame with strong cord or wire.
  5. Remove the 6 front halfshaft-to-differential bolts.
    WARNING Use care to avoid damaging the hub seal when removing the front halfshaft.

    jturcotte_175.jpg

Fig. Halfshaft-to-differential mounting bolts (3 of the 6 bolts shown)-2001-03 F-150 and 2004 F-150 Heritage Edition


7. Remove the inboard end of the halfshaft from the differential case or extension axle case. Separate the front halfshaft and joints from the hub, then remove the halfshaft and joints from the vehicle.



To install:

  1. Slide the halfshaft outboard end into the hub, making sure that the splines engage.
  2. Situate the inboard end of the halfshaft against the front differential flange and install the 6 halfshaft-to-differential bolts. Tighten the halfshaft bolts to 60 ft. lbs. (82 Nm).
  3. Install the front disc brake caliper onto the rotor and anchor plate, then install and tighten the 2 caliper mounting bolts to 21-26 ft. lbs. (28-36 Nm).
  4. Lift the lower suspension arm and steering knuckle up until the upper ball joint stud is inserted into the steering knuckle. Install the upper ball joint castle nut and tighten to 57-76 ft. lbs. (77-104 Nm). Install a new cotter pin.
  5. Install the hub nut onto the halfshaft and tighten the hub nut to 221 ft. lbs. (300 Nm).
  6. Install the hub nut retainer and a new cotter pin.
  7. Install the front wheels and tighten the lug nuts in a star-shaped sequence to 83-112 ft. lbs. (113-153 Nm).
  8. Lower the vehicle to the ground.

Jan 23, 2011 | 2002 Ford F250 Super Duty SuperCab

1 Answer

How do you change a front axle u-joint on a 2006 3500 dodge ram


you will have to change both sides to start with. I'm doing this on a 1996 ram 1500. first, put the truck on 2 wheel drive or neutral for traction, raise vehicle, i got a lift it's easy, remove both wheels, calipers and rotors. unlock the driveshaft nut (cotter pin) and unbolt that nut. on the inside of the hub, first mark the relation on one side between the yoke and the shaft, then, there is 3 bolts holding the hub in, remove them. next, more cotter pins, upper and lower ball joint and tie-rod end need to come out, so, unscew the tie-rod end first and seperate it with ball joint seperator. do the same for the upper and lower ball joints. seperate the spindle and the axel should come out. the rest is standard procedure to change a ball joint.
let me know if it's enough info or if you want more please.

Jan 04, 2011 | 2008 Dodge Ram Pickup 3500

1 Answer

How to remove upper and lower ball joins on a 4x4 bronco full size 1986


For Lower & Upper Ball Joint Step by Step :

For That you use a C-clamp style ball joint press to remove the ball joint from the suspension arm-note the location of the receiver cup ! For installation of the ball-joint, use the same tool when pressing the ball joint into the suspension arm-again, note the location of the receiver cup.

Step by Step :

  1. Raise and support the vehicle safely, with jackstands.
  2. Remove the spindle and the ball joint assembly from the vehicle.
  3. Remove the snapring from the ball joint. Using a ball joint removal tool, remove the ball joint from the spindle. Do not heat the ball joint or the axle to aid in removal.
  4. Installation is the reverse of the removal procedure. Torque the ball joint stud nut to 85-110 ft. lbs. for 1983-89 Ranger and Bronco II.

    Please Rate, Thank you !

Aug 13, 2010 | 1994 Ford Bronco

2 Answers

How do I replace the front wheel bearings on a


remove cv outer nut, tire brake caliper and lower ball joint use a bar to pry against lower a frame to seperate ball joint slip out cv axel then remove four nuts securing wheel bearing. I would have to check at home for exact instructions.

May 18, 2010 | 2005 Chevrolet Silverado

1 Answer

I replaced hub on front axel but the noise is


It sounds like it is a front end suspension problem. The following should be checked: upper and lower ball joints, the sway bars links, and even the shocks. Replace what is problematic, and your front-end noise should disappear, if it is a front suspension problem. Hopefully, this will FixYa problem!

Jan 04, 2010 | 2001 Ford Excursion

1 Answer

How to replace lower left front ball joint ?


Removal & Installation NOTE This procedure requires the use of the following special tools: J 9519-E Lower Ball Joint Remover and Installer, J 34874 Booster Seal Remover/Installer, J 41435 Ball Joint Installer, J 45105-1 Ball Joint Flaring Adapter and J 45105-2 Receiver.

  1. On 4WD vehicles, remove the wheel center cap and drive axle nut.
  2. Raise and support the vehicle.
  3. Remove or disconnect the following:
    • Tire and wheel
    • Wheel hub and bearing, if necessary
    • Outer tie rod retaining nut
    • Out tie rod from the steering knuckle using a suitable puller
    • Brake hose bracket retaining bolts and bracket
    • Upper control arm-to-steering knuckle pinch bolt and nut
    • Upper control arm from the steering knuckle
    • Lower ball joint retaining nut
    • Steering knuckle from the lower control arm using a suitable ball joint removal tool
    • Steering knuckle from the vehicle
    • Lower ball joint flange with a chisel
  4. Install tools J 9519-E and J 34874 to the lower ball joint, then use those tools to remove the lower ball joint from the lower control arm.
To install:
  1. Install or connect the following:
    • Lower ball joint to the lower control arm, using tools J 9519-E, J 41435 and J 45105-2
  2. Remove the tools from the lower control arm.
    • Tools J 9519-E and J 45105-1 to the lower ball joint
  3. Flare the lower ball joint flange with J 9519-E and J 45105-1, then remove the tools from the lower ball joint.
    • Steering knuckle to the lower control arm
    • Lower ball joint retaining nut and tighten to 81 ft. lbs. (110 Nm)
    • Upper control arm to the steering knuckle
    • Upper control arm pinch bolt and nut and tighten to 30 ft. lbs. (41 Nm)
    • Brake hose bracket to the steering knuckle
    • Brake hose bracket retaining nuts and tighten to 7 ft. lbs. (10 Nm)
    • Outer tie rod to the steering knuckle
    • Outer tie rod retaining nut and tighten to 33 ft. lbs. (45 Nm)
    • Wheel hub and bearing, if removed
    • Tire and wheel
  4. Lower the vehicle
    • Drive axle nut, if 4WD, and tighten to 103 ft. lbs. (140 Nm)
    • Wheel center cap, if removed
  5. Check the front wheel alignment.

Nov 30, 2009 | 2002 Oldsmobile Bravada

1 Answer

Upper and lower ball joint replacement


to remove the axles, remove brake caliper and disc, remove hub assembly, the center hub/axle nut and...(there are i think 3-4 bolts on the back side of the spindle to remove the hub), you may have to force the hub off the spindle with a hammer or air hammer... once the hub is out the axle should slide out of the front differential allowing access to the ball joint nuts for removal...

Jun 12, 2009 | 2000 Dodge Ram 1500 Truck

3 Answers

Remove front axle from differential on 2003 dodge ram


That works fine on a relatively new vehicle but one that has run in salt etc you'll save a lot of time if you remove the steering knuckle completey by separating lower ball joint and outer tie rod end ball joint and bring the whole steering knuckle to a bench to separate the hub/bearing. Soak everything with penetrant, loosen the bolts a few turns and try hitting right on the bolt heads. I also made a very sharp wedge from a chisel and rammed it hard on the other side to seoarate the hub. It will finally come apart then you'll see all the **** that was binding it due to an alumininum knuckle re-acting with a steel hub. Clean the hole and grease everything and fit new bearings

Jan 06, 2009 | Dodge Ram 1500 Cars & Trucks

Not finding what you are looking for?
2003 Ford F250 Super Duty Crew Cab Logo

283 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...