Question about 1992 Isuzu Rodeo

1 Answer

I have a 1992 rodeo and it is a manuel when I am driving there is like a squecking noise but when i push the clutch peadle in the noise goes away

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,074 Answers

I would say it sounds like the CV joints

Posted on Oct 17, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Loud squecking noise when steering


replace the drive belt the back of the drive belt has to just a bit above the edges of the pulley or it will slip
make sure that the correct "v" section belt is in use

Jun 21, 2017 | Cars & Trucks

1 Answer

Grinding when clutch is not engaged. Sound goes away when clutch IS engaged (i.e. pushed to the floor). Only makes noise when you let clutch out and while driving. Makes noise sitting in neutral too.


the throw out bearing is what I am thinking Sue.
may as well have a new clutch put in too as its the same amount of labor to do the whole thing as it is to just replace the throw out bearing.

Oct 12, 2011 | 2000 Hyundai Accent

2 Answers

I have a 2000 Isuzu Rodeo in which the clutch pedal went to the floor & stayed there. Upon inspection, the clutch master cylinder was empty on fluid. I filled the reservoir & bleed the clutch...


It sounds as if you have 2 problems here.

The fact that the clutch pedal went to the floor and stayed there suggest a fault in the master cylinder. It may be that you need to overhaul the master cylinder.

Overhaul kits are available at less cost than a clutch master cylinder:
0results for isuzu rodeo clutch master cylinder overhaul kit

The grinding noise ... A grinding noise would be caused by either the gear not engaging properly because of the defective clutch.

Or, if it is more of a squealing noise - that may be the clutch release bearing at fault.

Are you absolutely sure that your entire clutch unit - pressure plate, driven plate and release bearing aren't worn?
116results for isuzu rodeo clutch

Mar 14, 2017 | 2000 Isuzu Rodeo

2 Answers

I have a 92 2 wheel drive Toyota pick up 5 speed transmission 2.4 liter engine. When I let up on the gas while in gear there is clicking/rattling noise in all gears except 4th gear. If I push down on the...


Sounds like you have a defectine cluthch componant. Best way to verify is get the rear axle off the ground . So as not to let the rear drive wheels make contact with the ground. Have an assistant start the truck and put it in gear. After making sure the vehicle is secure crawl under the vehicle and listen to comfirm that the noise is coming from the clutch area.

Mar 25, 2010 | 1992 Toyota Pickup

1 Answer

Manuel transmission nocking


While in Neutral, push the clutch pedal in and see if the noise changes. If so, you need a new clutch kit because your release bearing is failing. Also called the "throw out bearing".


Feb 12, 2010 | 1992 Honda Accord

1 Answer

Grinding in the gearbox area while driving


manual ,thank heaven ,dont see many autos here in spain,right without driving car so i can hear it then it stands two possibilities ,when clutch is depressed you hear a noise like a grinding squel ,this is the thrust bearing ,if you hear a rumbling noise that disappears when clutch is depressed then this is lay shaft bearings ,Now also the problem can be the fingers on the clutch plate are worn and the bearing is pushing the clutch plate fingers down but if one or two are worn away then the thrust bearing is being pushed through the pressure plate ,either way a new clutch is need and as these vehicles are rear wheel drive they are not difficult to renew ,Just have to make yourself a clutch alignment tool from a broom handle .Dont be scared of it they are not that difficult to do just dirty and messy thats all the hardest part is aligning the clutch so the spigot shaft goes through easly and you dont have to struggle pushing the gearbox in

Dec 12, 2009 | BMW 325 Cars & Trucks

1 Answer

Tranny problems


did you change the bearing in the flywheel the center one or throw out bearing that pushes out on to the presserplate

Jan 18, 2009 | 1992 Isuzu Rodeo

1 Answer

1992 Ranger xlt 3.0 Manual 5-speed (Any clutch adjustments?)


FORDS ARE OK if the noise u are hearing is going away when u press the clutch it sounds like it is comming from the gearbox. the gearbox stops turning wheh u hold the clutch in is the gearbox noisey when u dive it 1-2-3-4 this will let u know if the gearbox is worn
is oil level ok ? check it and transfere case

hope it helps let me know if u need more help

Dec 19, 2008 | 1992 Ford Ranger

1 Answer

1992 ISUZU RODEO CLUTCH PROBLEM


could also be the host/tube connecting the master and slave together. Could be a small hole that sucks in air when you let off the clutch and pushing the fluid out on to a host that is so dirty or in such a dark place that you can't see the fluid seeping out on the hose

Good Luck

Nov 10, 2008 | 1992 Isuzu Rodeo

2 Answers

2005 rodeo 4wd turbo diesel


possibly the throw out bearing....which is part of the clutch assembly

Oct 09, 2008 | 2004 Isuzu Rodeo

Not finding what you are looking for?
1992 Isuzu Rodeo Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...