Question about 1994 Chevrolet S-10 Blazer

1 Answer

Where is the num. one cyl.on the distrbutor cap on a 1969 amc rambler w/ a 232 eng.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

Number one on the cap is anywhere you want to start number one. As long as the firing order is in the correct order.

Posted on Oct 17, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Wont install booster brake and vacuum on 1965 amc rambler and Hydraulic steering

I saw one at Well known, great online parts store. Their catalog makes it easy to look at everything they have in stock for your 1965 model. Best thing about RockAuto is they usually have the lowest prices on everything. Do-it-yourselfers give them a lot of business.

Oct 07, 2016 | AMC Cars & Trucks

1 Answer

How can I install an AMC 360 engine into my 1965 rambler classic with a 287 engine?

what I did was removed the 287 engine installed an AMC 360 .In order to do this you have to get an borg warner m11 bell housing from 67 to 71 .amc used borg warner transmissions until than. So you put the m11 bell housing on to the m8 transmission and get the motor mount for the AMC 360 engine

Feb 10, 2015 | AMC Cars & Trucks

1 Answer


Don't worry about actually pointing toward # 1 cylinder, just the tab under cap that goes to # 1 spark plug wire. # 1 cylinder needs to be at TDC on compression stroke, and rotor pointing at # 1 wire tab under cap.

Jan 15, 2014 | Dodge Ram 1500 Cars & Trucks

1 Answer

Fuel line routing diagram

Back in those days there was no return line. Just had to have a vented gas cap.

Oct 04, 2013 | AMC Cars & Trucks

1 Answer

How do you set the points on a196 cu. in motor

Mark the position of the distributor. Remove cap. Loosen the distributor hold down bolt.and turn distributor to raise the points cam follower to one of the lobes on the cam. Remove the screw that holds the points assembly. Remove points with the capacitor attached. Put you new points in the same position as the ones that you removed. Points should have .030" gap. Tighten points- hold-down screw. Turn the distributor to the original (marked) position. Tighten distributor hold-down bolt. You should now be able to start, but you may need to set the timing.

May 02, 2012 | AMC Cars & Trucks

2 Answers

( I only entered Concord as my Model because there is no Hornet / Gremlin option) I need a Borg - Warner T-35 automatic for the AMC 1970 (or 1971) Hornet (or Gremlin) 232. My question is which (if any)...

Now not quite sure here and i assume your in america for this borg warner unit as they were extensively used on cars like the old rover which was then called british leyland so it would appear across the range on rover ,austin ,triumph also the old jaguars as well ,but i think you would have to change the bell housings ,These gearboxes were not difficult to repair for things like clutch linings and brake bands as any reconditioning shop for brakes and clutches should be be able to cut some ferodo material and fit for you but the rest of it ?? i wouldnt know if any parts are still available .Now as for converting it to a manual then this isnt a problem providing you get the flywheel with the gearbox and all the gearchange linkage and if possible the prop as well as it could be a different length but again any decent engineering shop could extend or shorten this for you providing you have the right end of the prop that fits into the gearbox .As for knowing exactly what is what i wouldnt know because being a europeon mechanic i have never seen this vehicle that you own.

Jan 27, 2011 | AMC Concord Cars & Trucks

1 Answer

1965 amc rambler vac diagram

There was only three vachum hoses on the 1965 the one from the carburator to distributor and the one from the intake manifold to the power brakes and maybe a PCV valve But think that was too early for PCV 1972 or 1973 is the first time it was introduced to cars.

Aug 22, 2010 | AMC Scrambler Cars & Trucks

2 Answers

Power steering box that will interchange with 1965 Rambler V-8

ramblers were a mixture of the" big three" back in the '60s you might see if a steering box from a dodge ram series pickups or ford f series pickups may fit. also,check closely on the steering box for a casting number,parts suppliers use these numbers as a cross reference to match other steering boxes to your application.

Jan 20, 2010 | AMC Cherokee Cars & Trucks

1 Answer

Distrbutor cap 1995 f-150

In a clockwise rotation the wire closest to the engine is cyl.3, then 6,2,4,1,5

Feb 06, 2009 | 1995 Ford F150 Styleside Regular Cab

Not finding what you are looking for?
1994 Chevrolet S-10 Blazer Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides