Question about 2008 Ford F-350

1 Answer

What is the head bolts torque down to on 2008 f350 6.4

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,074 Answers

Hope this is what you needed, Tim;

http://www.thetruckstop.us/forum/showthread.php?612-Torque-Specs

Posted on Oct 17, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the 2008 Toyota Yaris 1.5 head bolt torque


The correct tightening sequence will usually be provided with new bolts. I expect like many modern vehicles there will be an initial torque setting followed by a further angular adjustment possibly followed by an additional angle setting.

Sep 07, 2016 | 2008 Toyota Yaris 1.5

1 Answer

98 ford windstar intake manifold torque specs


Intake torque specs ' FordForumsOnline.com

www.fordforumsonline.com > Ford Tech Forums > Engine & Drivetrain

May 7, 2010 - 2 posts - ‎2 authors
ISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).

Torque Specifications - AutoZone

www.autozone.com/.../Ford-Windstar.../Specifications/Torque-...

AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

I need the head bolt torque specs and sequence for a 2008 Suzuki reno 4 cylinder


well it's at alldata.com and at suzuki pitstop plus dot com.
here ill do that for you....
4 banger no displacement stated, now that is a challenge.


now the words..... USA car... 2.0L vin Z

Cylinder head bolts. Tighten the cylinder head bolts gradually and in the sequence shown. Tighten the cylinder head bolts to 18 ft. lbs. (25 Nm) and turn the bolts another 3 turns of 90 degrees using the angular torque gauge KM-470-B.




25750556-4duymjxl1ar05igx5z0a5r0z-5-0.jpg

Jun 17, 2015 | 2008 Suzuki Reno

1 Answer

2008 dodge charger with a 2.7 liter engine head boly specs


  1. 2.7 litre intake bolt torque spec in a 2008 dodge charger ...

    www.fixya.com/cars/t18664111-2_7_litre_intake_bolt_torque_spec_in Jun 27, 2013 - Head Bolts Step one 37 ft lbs then tignten 120 degrees more. Rocker arms. Step one 11 ft lbs then tighten 90 degresss more. Upper intake 89 inch ...

Feb 28, 2015 | 2008 Dodge Charger

1 Answer

2008 CHEVY HHR TORQUE SPECS FOR HEAD


    DO NOT use any sealing material.

  1. Install the cylinder head gasket.
  2. Install the cylinder head.
  3. Install NEW cylinder head bolts.
  4. Caution!Refer to Fastener Notice in Cautions and Notices.

    412510.gif
    Click to Enlarge

  5. Install and tighten the cylinder head bolts in the sequence shown.
  6. Tighten
    Tighten the bolts to 30 N•m (22 lb ft) plus an additional 155 degrees using the J 45059 .

    412425.gif
    Click to Enlarge

  7. Install the NEW front cylinder head bolts.
  8. Tighten
    Tighten the bolts to 35 N•m (26 lb ft).

/f 412425.gif412510.gif

Feb 19, 2013 | 2008 Chevrolet HHR 2.2

1 Answer

Help please What torque are the cylinder head bolts on peugeot expert 1.6 hdi 2008 i need to put the head back on


no problem the correct setting is ,hmm it says tighten to 20nm then 40nm and then slacken off 130? and tighten 130? ,well this the proverbial brown stuff from a cow to me as when i do these engine i pull down with a speed key then a rachet then my 80cm snap on bar so i suppose iam pulling down to around 75/80 lbs per inch but in all honesty i never use a torque wrench as i used to torque heads in ford of dagenham at 18yrs old so three engine a minute i just sort of feel for the bolt stretch and that it really .

May 03, 2011 | Peugeot Liberte Cars & Trucks

2 Answers

Head bolt torque for 2008 6.4 ford f 350


this its the factory procedure to torque the cylinder heads

  1. NOTE: If bolt chatter occurs during Stage 4 or 5, loosen the bolt and repeat Stage 3.
    Tighten the cylinder head bolts in 7 stages in the sequence shown:
    • Stage 1: Tighten bolts 1 through 10 to 95 Nm (70 lb-ft).
    • Stage 2: Loosen bolts 1 through 10.
    • Stage 3: Tighten bolts 1 through 10 to 156 Nm (115 lb-ft).
    • Stage 4: Tighten bolts in sequence 1 through 10, an additional 90 degrees.
    • Stage 5: Tighten bolts in sequence 1 through 10, a second time, an additional 90 degrees.
    • Stage 6: Tighten bolts 11 through 15 to 24 Nm (18 lb-ft).
    • Stage 7: Tighten bolts 11 through 15 to 31 Nm (23 lb-ft).
ganyapr.jpg

Feb 13, 2011 | Ford F-350 Cars & Trucks

1 Answer

WHAT IS THE PROPER HEAD BOLT TORQUE SEQUENCE AND SPECS FOR THE INLINE 6 4.9? FORD


OKAY GET A PIECE OF PAPER I WILL GIVE YOU 2 ROWS OF NUMBERS TO WRITE DOWN. THAT WOULD BE YOUR TORQUE SEQUENCE. OKAY FROM LEFT TO RIGHT WRITE NUMBERS. 11 7 3 2 6 10 14 OK WITH THESE NUMBERS PLACE THEM UNDER FIRST SET OF 7 NUMBERS I GAVE YOU. FROM LEFT TO RIGHT. WRITE NUMBERS 13 9 5 1 4 8 12. NOW THIS IS HEAD BOLTS TORQUE YOU HAVE 3 HEAD BOLTS PASS FIRST PAST TORQUE BOLTS ALL TO 50 - 55 FT LBS FOR SECOND PASS TORQUE ALL BOLTS 60 - 65 THIRD PASS TORQUE ALL BOLTS TO 70 - 85 FT LBS.

Nov 13, 2010 | Ford F-150 Cars & Trucks

1 Answer

1986 Mustang 3.8L cyl. head torque.


The aluminum heads on a cast iron block require some gentle torque procedures.... It may not be necessary - but I suggest that you start near the center of the head and work out with each tightening step. This will ensure that you don't put too much pressure on a single portion of the head. The standard proceedure for the 3.8 V6 up until 1994 is as follows:
You will have some long and some shorter head bolts. Place a small mark on the long bolts to identify them during the final torque proceedure.

Step 1: 15 (on all bolts)
Step 2: 29 (on all bolts)
Step 3: 37 (on all bolts)
Step 4: Now, starting near the center of the head, loosen a single head bolt about 2 turns. Now, torque it down to about 15 (+/- 3 lbs) IF A LONG BOLT.
OR 11 (+/- 3 lbs) IF A SHORT BOLT.
Step 5:
After all bolts are set as described above, ....go over them 1 more time, starting near the center of the head and pull each bolt down another 1/4 turn (90 degrees).
You are done!!

Oct 10, 2009 | 1986 Ford Mustang

Not finding what you are looking for?
2008 Ford F-350 Logo

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...