Question about Pontiac Grand Am

Open Question

How to remove rear bumper on a 2000 grand am - Grand Am Pontiac Cars & Trucks

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

eitan
  • 291 Answers

SOURCE: remove the rear bumper

Removing Prowler Rear Bumpers First remove the four 10 MM bolts holding the trans cooler and drop it down. Support it by attaching one bolt to the lower hole on the cooler frame. This will keep the weight off the lines. This takes two min. and allows easy removal of the elect. lines. Then remove the four bolts on each bumper. The bolts are 13MM and 17MM. You will need a ratchet, sockets, extension and a 13MM open end wrench. If you remove the rear bumpers, you should replace the rear pan with one of the aftermarket ones otherwise you will have big holes staring at the people behind you. Go to prowleronline.com and check the vendors for a couple of options. Maybe you are removeing them to paint and reinstall. Look at this link for some options .. Mine is the 7th post down. http://www.prowleronline.com/ubb/Forum1/HTML/014949.html Hope this helps.

Posted on May 15, 2008

3bachelors
  • 52 Answers

SOURCE: 2000 Infiniti I30

Sure! pop the trunk and remove screws and screw covers inside, then look in the wheel wells for the remaining screw/clips. Lastly underneath, near exhaust may be a few last screws to keep from flapping. Just make sure to watch for any wires from rear cameras, or reverse sensors. You will not need to remove any of the foam behind bumper.

Posted on Sep 03, 2008

  • 99 Answers

SOURCE: Remove rear plastic bumper cover

please email me at meanness628@aim.com with any other info or questions if you have already gone to a body shop

Posted on Sep 29, 2008

SOURCE: REMOVAL OF REAR BUMPER COVER ON 1997 DODGE STRATUS

See under the bumper its strap with clips,you must take it out from it,

Posted on Sep 10, 2009

Testimonial: "I found out there are clips on each side of the b umper under the rear 1/4 panels as well. thanks"

  • 4793 Answers

SOURCE: Volkswagen Passat rear bumper removal

all the screws/bolts are underneath the plastic cover.hex head.(allen key)

Posted on Jul 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How does the back bumper of the Ford Excursion attach?


The process is like the Super Duty trucks, so watch the video at the link. How to Fix F250 Super Duty Rear Bumper

Sep 06, 2016 | 2000 Ford Excursion

1 Answer

The rear bumper cover came off how can I reinstall it


2000 Toyota Sienna rear Bumper cover replacement (1998 ...

? 3:40
https://www.youtube.com/watch?v=AY1BBdg3q74
Sep 20, 2013 - Uploaded by SergSpace
2000 Toyota Sienna rear Bumper cover replacement (1998-2003) .... Automotive Bumper Repair Specialist- How to repairyour plastic bumper cover ... Toyota Sienna Rear Shock Installation 2003, 2004, 2005, 2006 - Duration: ... 2015 Toyota Sienna XLE - Duration: 28:13. by MikesCarInfo 35,234 views.

Fixing My Mom's Prius: Loose Rear Bumper Cover - YouTube




Nov 29, 2015 | 2005 Toyota Sienna LE

1 Answer

How do I remove rear bumper on 2003 jeep grand cherokee


RTM? yet, if not why not?
most cars, remove skins
the unbolt it.
click ZJ
then read frame and bumper chapter.
ask questions if not clear.
11 steps in chapter 13 , page 1 and 2
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

Sep 28, 2014 | 2003 Jeep Grand Cherokee

1 Answer

How to replace the electric fan on 2000 jeep grand cherokee


You must remove the entire front bumper and you will want to remove the radiator as well. There really isn't enough room there.

Remove headlights.
To remove the front bumper, there are plastic clips around wheel well and under the front bumper. Then there are a couple of bolts under the hood and two bolts on the side (look from wheel well up). The whole thing comes off as one piece.

I was able to move (twist) the A/C condensor out of the way and not drain it.

Jul 10, 2014 | 2000 Jeep Grand Cherokee

1 Answer

How to remove back bumper on 2000 jaguar xj8


remove rear mudflaps if fitted, remove screws from rear of wheel arch liners. two 19mm headed bolts from underside of bumper, be warned they sieze and a lot of force will destroy the bumper mounts and the bumper beam not cheap to repair.

Oct 31, 2013 | Jaguar XJ8 Cars & Trucks

1 Answer

05' Grand Caravan, told that 2 of the rear bumper parking sensors need to be replaced. What is the proper term for these, as I can't find them anywhere, and how invasive to replace?


I wish I had good news but rarly does this sensor go out. unless someone rear ended you. in this case the bumper cover has to be removed.

Dec 20, 2011 | 2005 Dodge Grand Caravan

1 Answer

How to remove the rear bumper cover on a pontiac 2004 grand prix


  1. Open the trunk.
  2. Remove the rear compartment sill plate. (Trim round the back edge of the trunk)
  3. Pull the left and right compartment side trim panels down to access the fascia bolts and nuts.
  4. Remove the tail lamps.
  5. Remove the fascia bolts and nuts from the rear bumper fascia 1 nut 1 bolt on each side near tail lights.
  6. Remove the push-in retainers from the top edge of the fascia.(4 plastic circles, pull up on center of cirle with screwdriver
  7. Raise and support the vehicle.
  8. From underneath Remove the push-in retainers from the rear bumper fascia (one on each side I think)
  9. Remove the fascia bolts from the rear bumper fascia. on on each side from, up where the facia connects to the quater panel)
  10. Remove the rear bumper fascia from the vehicle

Apr 14, 2011 | 2004 Pontiac Grand Prix

1 Answer

How do I change the bumper on a 2000 Blazer


Front or rear, I am guessing it is the rear as they tend to get the most abuse and or rust! Start by removing the plastic step guard on the top of the bumper (use a flat ply bar) you will see the four bolts (remove those) and directly inline with those from the underside you will see four more (remove those) your bumper is free, there is one wire connector to release (licence plate lights) and simple lift off the bumper.

Dec 08, 2010 | 2000 Chevrolet Blazer

1 Answer

99 Plymouth Voyager Rear Bumper


If you look up from under you should see some push clips. if your removing entire bumper with rebar & all, it's probably about 4 nuts holding it to bumper shocks, but be sure to look near ends at fenders for push clips , and or screws, and across mid section. watch it, it's pretty heavy with the rebar attached so make sure you have everything ready & remove nuts last, with some help to hold it up.

Aug 05, 2008 | 1999 Plymouth Grand Voyager

2 Answers

1996 grand cherokee bumper


there is a trim panel on top of rear bumper if you look underneath there are clips that go through metal bumper also there are 4 plastic fasteners that will need to be replaced after removing best to get clips at dealer cheap enough hope this helps ya

Jul 07, 2008 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...