Question about 1995 Mercury Grand Marquis

1 Answer

I have a 95 grand marquis GS that floats around like a boat on the water, what do I have to get to fix this problem? does the car have struts and what about a bushing kit.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Mercury Master
  • 5,501 Answers

I had a 94, and now an 02, and have experienced some of the same problems. You would see a problem with the Bushings in tire wear. If you experience pulling or drifting to the same side as your last turn, have your balljoints checked.

Check your tire pressure, especially if this is a recent problem or you use a Quick change oil place. Make your tires harder by inflating them while staying below the Max amount. If you have tires with soft sidewalls the float will not go away.

The fronts have shocks. An alignment would show if bushings were needed. I put a 100,000 miles on my 94 after replacing the shocks, but they were replaced at 61000 giving the total 161,000 on the Air suspension. My 02 is still factory equipped.

This series of cars were durable vehicles. Any handling problem pointed to tires and Alignment. So far shocks are staying reasonable priced and you can get good deals on the Web, but deal with firms who give free shipping.

Posted on Oct 17, 2010

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

95 grand marquis passenger side rumbles when i hit bumps whats the problem

You did not say if noise is in front or rear of the car. It could be loose exhaust or sometimes the front calipers or brake pads will "float" against the turning rotors when they are jarred.

Feb 27, 2014 | Mercury Grand Marquis Cars & Trucks

1 Answer

1994 Mercury Grand Marquis temp gauge reads hot

Check sending unit, Ford/Mercury put out a TSB, technical service bulletin : Article No. 95-13-2 07/03/95, on erratic temp sender units.
You troubleshoot as follows :
  1. Turn ignition switch to On or ACC position.
  2. Connect a 10 ohm resistor between gauge lead and ground. The centerline of pointer should fall within the band around the H mark.
  3. Connect a 73 ohm resistor between gauge lead and ground. The centerline of pointer should fall within the band around the C mark.
  4. If gauge tests within calibration, replace sender.
  5. If gauge is out of calibration, replace gauge.

Mar 16, 2013 | 2000 Mercury Grand Marquis

1 Answer

Good engine swap for a 94 grand grand marquis

Another 4.6 out of a '94 Grand Marquis. If you can. That way all the sensors will be correct and the wiring harness will plug-and-play. You can install almost any 4.6 but, depending on the year, there's going to be a lot of issues making them work with the electronics in your '94 Marquis.

Nov 08, 2009 | 1994 Mercury Grand Marquis

1 Answer

Are there special tools required to change a fuel filter on a 2007 mercury gran marquis? it appears there may be.

yes its called a fuel line dissconnect tool you can get them at any parts store for around ten bucks

Jun 09, 2009 | 2007 Mercury Grand Marquis GS Sedan

1 Answer

Does anyone have information on how to remove and replace the front struts for a 1991 grand marquis? Pics would be cool

I dont have the exact model in my notes but you can figure your fix with my references.. Ford used the Mcphearson strut assembly on a wish bone suspension alot...
I attached pixes of various kinds never undo the bolt on the center top of your strut just promise to read this through
5b264fc.jpg 840b930.jpg the three bolts hold the whole assembly in place some are on strut tower some you have to go to a arms to find..
the next step is clamp it and remove the center nut stay clear from both ends remove the nut slip off spring put spring over new strut make sure the cut coil seats properly on the bottom of the strut then reinstall the the upper insulator and stud mount Ive torqued some around 45 ft lbs...
be careful good luck Im me if you need help!!!

May 09, 2009 | 1991 Mercury Grand Marquis

1 Answer

Where do I connect the obd1 scanner for a 95 grand marquis

try under the hood, drivers side, near the hood hinge. against the firewall. will be an almost rectagular shape. may or may not have a cover that covers the terminals. kinda behind the strut tower.


Feb 19, 2009 | 1995 Mercury Grand Marquis

Not finding what you are looking for?
1995 Mercury Grand Marquis Logo

319 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts


Level 3 Expert

75824 Answers


Level 3 Expert

5501 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides