Question about 1991 Dodge Dynasty

1 Answer

Was running good would shut off but start back up. now no spark. have checked coil pack, thats good . what could it be?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 120 Answers

I had one of these before like this. I checked everything for spark and all checked good. a new ecm fixed my problem. it is located near the air filter housing.

Posted on Oct 16, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Getting a rapid misfire in cylinder 5 changed spark plugs ,cleared the code came back on the day later ???


Hi Jason, Sounds like you have a coil pack and one of your coils is faulty. To check which coil is faulty just pull a spark plug lead off a spark plug and plug the spark plug lead onto a SPARE spark plug, Now earth it to the CLEAN motor or body (make sure the spark plug is touching metal) Start the motor, it's going to run ROUGHER than usual but you'll see if that spark plug is sparking... If it sparks then that coil is good. Turn the motor off and replace the spark plug lead back on to the original spark plug. Repeat with the next spark plug lead and so on until you start your car and the spark plug doesn't spark, THAT'S YOUR FAULTY COIL...

Apr 14, 2016 | Cars & Trucks

2 Answers

Jeep 3.7 cylenders 2 & 4 not firing


3.7 V6, mileage?

most likely the HV wires bad.

then bad coil pack.

did you check spark directly at the coil pack?

i use 2 known good HV wires to do that and 2 good test spark plugs.

both plugs grounded to engine (shell)

that is how you test any wasted spark coil pack. 3 coil pack.

if that fails the FSM shows, unplugging it and check the coil resistances. if wrong the pack is bad,

keep in mind the res. can read ok and coil be bad ,due to internal insulation break down (internal shorts)

if thats ok. the resistance , make sure the wires are not (primary)

to the coil (the low voltage connnector)

if that is ok, its mostly likely a bad coil, (pray not bad PCM)

if tool-less? start with cheap parts , work to expensive. (guessing)





now wasted spark 101.

if one line opens , both spark plugs die. no spark

the wasted spark is wired in SERIES. ( like Christmas lights)

the magic cuts cost of 6 coil\'s.

so if the HV wires are say, cheap , carbon wire and open

you lose, both spark plugs. use MAG wire and end this issues.

get some nice NGK mag wire or Bosch Mag wires.

you can see i hate carbon wire. for good causes.

(carbon string wire)

mag wires is real wire that is coil spun and is inductive. it

has the correct impedance but is not a resistor its and inductor.

and lasts the longest , and worth every penny.

Mar 29, 2014 | 2006 Jeep Liberty

1 Answer

2007 fusion no spark on any coils.


2007 Ford Fusion 3.0L V6
Spark Plugs Gap 0.044"----0.057

The Coil Pack*s is toast. And spark plug*s All 6.
It is recommended: These parts two Coil Packs, and 6 spark plugs/& maybe wires, are purchased from Original Equipment Manufactuer (OEM)

Mar 08, 2017 | Cars & Trucks

1 Answer

2000 ford explorer Have a p0305 code started a while back when accelerating to pass a car the truck would **** and the check engine light would blink but once i take foot of the gas it would go back to...


A PO305 code is for a Cylinder #5 misfire code. This would definitely cause a lack of power when passing and would cause the check engine light to blink when you are into the throttle and then stop once you let off the throttle. This could be caused by a faulty coil pack or a bad spark plug for that cylinder. I dont know which engine you have in this vehicle, but if each spark plug has its own coil, you can try unplugging the coil pack for cylinder # 5 while the vehicle is running and if it changes the way it runs then the coil pack is probably good, but if there is no change when you unplug the electrical connector, there is a good chance the coil pack is bad. It is not unusual for these coil packs to burn out.

Hope this helps... if there is anything further i can help you with, please feel free to ask.

Sep 14, 2011 | 2000 Ford Explorer

1 Answer

A 1996 ford taurus with no spark


Hello you say no spark again well in the past i have replaced coils on Fords same day the coil pack quit!.So perhaps return it as a faulty pack.Manufactures still makeing defective parts!.Also if you have service engine light on you should have a OBD 2 scan to retreve any electrical faults might be.

Dec 26, 2009 | 1996 Ford Taurus

1 Answer

Arcing at coil pack. misfire on #1 cylinder. car ran rough, now won't start. How do i change the coil pack?


follow the spark plug wires to the coil packs...i believe now, you have to physically crawl under the vehicle and look at the back of the engine, to the coil packs....remove all three packs as an assembly and then remove the individual pack that you need to replace...or if you feel good enough, see if you can run your hands the back side of the engine, and remove the coil packs that way....good luck...if you need help....just call me....you in edmonton?

Nov 18, 2009 | 2000 Pontiac Sunfire

1 Answer

1980 gmc shut off while driving. no sputter no nothing just died.. battery good.. getting fuel to the carb... getting spark from the plugs.. distrib is good...timing is good... any other reasons for the...


The spark you are getting is to weak.Check and clean the wires from the coil pack.If they are ok then change the coil pack.Then the crank sensor.Hope that was helpfull.

Jul 29, 2009 | GMC Sierra 1500 Cars & Trucks

Not finding what you are looking for?
1991 Dodge Dynasty Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...