Question about Nissan Pulsar

1 Answer

Repace cv joint boot - Pulsar Nissan Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,418 Answers

You can get a universal boot, Which is a clamshell type. You remove the old boot with a knife and wire cutters to cut the clamps. You will need a can of spray brake cleaner to clean the CV joint of dirt. The CV boot (kit) will come with new grease to refill the joint. The kit comes with a glue to glue the boot together once installed in place. Plus new clamps and adapters for most cars. This one (see link) will fit 177 different Nissan models. I am posting a picture and a link to the site for you to check it out. The other alternative is to pull the wheel and pull the Cv axle off the car. Which is a tuff job in the driveway. - http://www.oreillyauto.com/site/c/detail/DOR6/614632.oap?
_-_-_...>>>repace cv joint boot - f578a50.jpg

Posted on Oct 16, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 34 Answers

SOURCE: How to disassemle CV joint

I have done CV joints here at my home garage for yrs, I recently did my 02 Esteem 1.8, I have a pic of the joint completely disassemble, and I mean as far as you can disassemble it. There are basically 3 types of joints, the rezeppa, which is the outer, the tripod and double offset joints are used on the inside.
The only tools needed are a large brass hammer, a vise, snap ring pliers, and CV boot clamp pliers.
You can remove both types of inners without special tools, the shaft has an external snap ring to hold on the race. The outer requires a vise and a large brass hammer, you hold the sahft in the vise, hold and pull on the joint and hit it close to the shaft, it has a circlip like the one used in the transmission, you have to "overcome" this clip. Then you simply turn the cage so to expose each ball out of the shell, and pluck it out, then rotate the inner race sideways and manauever it out, then the cage the same way.
The inner depends on what type, the tripod type come right out once the boot is removed, the double offset type is similar but it has a large circlip which can be plucked out with a small pick, it is a very weak clip. Then the cage and ball will litterally fall apart in you hands.
Clean and degrease all parts.

Assembly is a snap, the outer one goes on first, once the cage and balls are in the shell, and greased, put the shaft in and push down while working the clip smaller until is collapses enough to fit in the groove of the shaft, then tap it on down, the clip will emerge inside the joint and snap out to full size again. Again this exactly the same principle used on the stub that goes in the tranny.
The inners are just assemle in reverse order. Install the inner race, or tripod,depending on which one you have, then the balls and outer race, push it in the sheel (tulip), install the large circlip making sure the gap fall in between a ball race, then fasten the boot.

Posted on Oct 16, 2008

  • 83 Answers

SOURCE: 97 toyota celica outer cv boot replacement passenger side

have you undone the main hub bolt, if yes, there could be two different items holding the cv joint on, one is a small circlip in the joint end, or the other is just like an expanding metal ring again only small. what i had to do to change my one was take the driveshaft out (easier to see whats there) then gently (rubber hammer) hit the CV joint it should then fall off to allow you to change the CV joint. I spent over an hour trying to get the metal ring off, then after taking driveshaft off it was changed and back on in ten mins. Or you can go to a motor factors or similar and get a boot puller, my opinion hammer works better lol

Posted on Jan 25, 2009

alicantecoli
  • 22156 Answers

SOURCE: 1998 nissan sentra, replacing cv joint boot covers

firstly remove the wheel trim and undoo the big nut on the end of the drive shaft,Then jack up and remove wheel and put stand under body remove the lower track control arm pinch bolt from lower suspension .remove brake caliper separate the lower arm from the bottom of the strut then push the drive shaft through the hub assembly and its clear .cut off old boot and look for the circlip that hold the end on which should be in the centre if the unit in a recess to allow access to the ends of the clip .You shouldnt need to remove the whole shaft just spread the clip and tap with a copper hammer.wash the thing out with diesel and take the balls out and give it a good clean ,rebuild and pack with grease slide the new rubber down the drive shaft ,refit the end but dot hit the threasded bit with a hammer put a block of wood their first then tap it on.Refit the suspension and away you go

Posted on Mar 14, 2009

cadman000
  • 607 Answers

SOURCE: cv boot clamp came off somehow from the outer hub assembly

athere is a snap ring within the CV joint the nedds to be spread OPEN to release CV joint from axle, Once CV is cleaned and repacked with grease rintall onto axle by again spreading apart clamp. Prior to installing CV joint slide NEW CV joint boot onto axle, Cleanly intall add'l grrease and reinstall CV boot.

Posted on Apr 04, 2009

  • 10 Answers

SOURCE: cv joint replacement 1998 isuzu trooper 4x4

This is a simple job that is why it is not very detailed in your book. Nothing special. Do one side at a time so you have a reference to how to reassemble it. Remove your tire , brake calipers be sure not to stress the rubber brake lines or open the brake lines to air. Remove both upper and lower ball joints. When taking out the ball joints remove the cotter pin and bolt and beat the **** out of the joint for it to release. Then the C/V axles will come right out with a bit out encouragement. You will need a few tools wrenches pry bar hammer. I would buy a Chilton's or a Haynes repair manual for torque specs for reassembly. Good luck and take your time. And unless the axles are making noise you can just replace the rubber boots. Which is alot cheaper.

Posted on Jun 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace rubber cv boot on 1999 Isuzu rodeo


how to , who can, what are all steps. are there special tools?
sure. if the boot is bad, so be the joint, Yah think?
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Halfshaft from the vehicle
    • Snapring and bearing
    • Snapring and oil seal
    • Mounting bracket
    • CV-joint boot
    • Circlip and inner joint housing
    • Snapring and spacer
    • Inner joint balls
    • Snapring and inner CV-joint
    • To install:
    • Install or connect the following:
      • Inner CV-joint and snapring
      • Inner joint balls
      • Spacer and snapring
      • Inner joint housing and circlip. Add 150 grams CV-joint grease.
      • CV-joint boot
      • Mounting bracket
      • Oil seal and snapring
      • Bearing and snapring
    • Install the halfshaft and mounting bracket to the vehicle.
    • Check the wheel alignment and adjust as necessary.

Jun 30, 2014 | 1999 Isuzu Rodeo

2 Answers

How to change cv joints


I would replace the complete axle assembly,
it would be cheaper and come with a warranty.

Instructions
  1. Remove the CV Joint
    • Remove the boot straps from the CV joint using a standard screwdriver or a pair of diagonal cutting pliers.
    • Slide the boot back over the interconnecting shaft.
    • Get Chevrolet Info at InsideLine Free News, Videos, Photos & More!
      Detach the stop ring at the base of the CV joint assembly using a pair of snap ring pliers.

    • Pull the CV joint assembly from the interconnecting shaft to force the snap ring at the top of the shaft through the CV joint assembly.
    • Tilt the inner cage (the cage holding the balls in place inside the housing) in different angles to remove the six balls. Use your thumb or a hammer and a wooden dowel, if necessary.
    • Tilt the inner cage enough to remove it from its housing.
    • Rotate the race inside the cage--the part that holds the balls against the inner cage--and remove the race from the cage.
      Replace the CV Joint
      • Apply a thick coat of grease to the new CV joint race using special high temperature/high pressure grease (see Tips below).
      • Install the race inside the new cage. Then install the cage/race assembly inside the CV joint housing.
      • Tilt the cage at different angles and fit the new balls in place.
      • Slide a new CV joint rubber boot over the interconnecting shaft.
      • Install a new snap and stop ring on the interconnecting shaft.
      • Push the interconnecting shaft through the CV joint assembly to force the snap ring through the assembly.
      • Apply a thick coat of CV joint grease to all moving parts of the assembly.
      • Apply a coat of CV joint grease to the inside of the rubber boot. Then slide the boot over the CV joint assembly.
      • Install the boot straps at each end of the boot, and tighten the straps using a clamp tool or screwdriver, depending on the type of clamp.


Mar 22, 2012 | 1997 Chevrolet Cavalier

2 Answers

Cv joint but the plastic thang that go around it


One would have to remove the half shaft to service the cv joint properly.

CV-Joints Overhaul Check the CV-boot for wear tccs7030.jpg

Removing the outer band from the CV-boot tccs7031.jpg

Removing the inner band from the CV-boot tccs7032.jpg

Removing the CV-boot from the joint housing tccs7033.jpg

Clean the CV-joint housing prior to removing boot tccs7034.jpg

Removing the CV-joint housing assembly tccs7035.jpg

Removing the CV-joint tccs7036.jpg

Inspecting the CV-joint housing tccs7037.jpg

Removing the CV-joint outer snapring tccs7038.jpg

Checking the CV-joint snapring for wear tccs7039.jpg

CV-joint snapring (typical) tccs7040.jpg

Removing the CV-joint assembly tccs7041.jpg

Removing the CV-joint inner snapring tccs7042.jpg

Installing the CV-joint assembly (typical) tccs7043.jpg

prev.gif next.gif

Oct 08, 2010 | 2004 Oldsmobile Alero

1 Answer

I've got a 1999 2500 Chevy Silverado , that I need to change a cv boot on , can u assist me.?


CV-Joints
Overhaul
These vehicles use several different types of joints. Engine size, transaxle
type, whether the joint is an inboard or outboard joint, even which side of the
vehicle is being serviced could make a difference in joint type. Be sure to
properly identify the joint before attempting joint or boot replacement. Look
for identification numbers at the large end of the boots and/or on the end of
the metal retainer bands.

The 3 types of joints used are the Birfield Joint, (B.J.), the Tripod Joint
(T.J.) and the Double Offset Joint (D.O.J.).

NOTE: Do not disassemble a Birfield joint. Service with a new joint or
clean and repack using a new boot kit.

The distance between the large and small boot bands is important and should
be checked prior to and after boot service. This is so the boot will not be
installed either too loose or too tight, which could cause early wear and
cracking, allowing the grease to get out and water and dirt in, leading to early
joint failure.

NOTE: The driveshaft joints use special grease; do not add any grease
other than that supplied with the kit.

Double Offset Joint
To Remove:

NOTE: The Double Offset Joint (D.O.J.) is bigger than other joints
and, in these applications, is normally used as an inboard joint.


  1. Remove the halfshaft from the vehicle.
  2. Side cutter pliers can be used to cut the metal retaining bands. Remove the
    boot from the joint outer race.
  3. Locate and remove the large circlip at the base of the joint. Remove the
    outer race (the body of the joint).
  4. Remove the small snap ring and take off the inner race, cage and balls as an
    assembly. Clean the inner race, cage and balls without disassembling.
  5. If the boot is to be reused, wipe the grease from the splines and wrap the
    splines in vinyl tape before sliding the boot from the shaft.
  6. Remove the inner (D.O.J.) boot from the shaft. If the outer (B.J.) boot is
    to be replaced, remove the boot retainer rings and slide the boot down and off
    of the shaft at this time.

To Install:

NOTE: Be sure to tape the shaft splines before installing the boots.
Fill the inside of the boot with the specified grease. Often the grease supplied
in the replacement parts kit is meant to be divided in half, with half being
used to lubricate the joint and half being used inside the boot.


  1. Install the cage onto the halfshaft so the small diameter side of the cage
    is installed first. With a brass drift pin, tap lightly and evenly around the
    inner race to install the race until it comes into contact with the rib of the
    shaft. Apply the specified grease to the inner race and cage and fit them
    together. Insert the balls into the cage.
  2. Install the outer race (the body of the joint) after filling with the
    specified grease. The outer race should be filled with this grease.
  3. Tighten the boot bands securely. Make sure the distance between the boot
    bands is correct.
  4. Install the halfshaft to the vehicle.

Except Double Offset Joint
To Remove:


  1. Disconnect the negative battery cable. Remove the halfshaft.
  2. Use side cutter pliers to remove the metal retaining bands from the boot(s)
    that will be removed. Slide the boot from the T.J. case.
  3. Remove the snap ring and the tripod joint spider assembly from the
    halfshaft. Do not disassemble the spider and use care in handling.
  4. If the boot is be reused, wrap vinyl tape around the spline part of the
    shaft so the boot(s) will not be damaged when removed. Remove the dynamic
    damper, if used, and the boots from the shaft.

To Install:


  1. Double check that the correct replacement parts are being installed. Wrap
    vinyl tape around the splines to protect the boot and install the boots and
    damper, if used, in the correct order.
  2. Install the joint spider assembly to the shaft and install the snap ring.
  3. Fill the inside of the boot with the specified grease. Often the grease
    supplied in the replacement parts kit is meant to be divided in half, with half
    being used to lubricate the joint and half being used inside the boot. Keep
    grease off the rubber part of the dynamic damper (if used).
  4. Secure the boot bands with the halfshaft in a horizontal position. Make sure
    distance between boot bands is correct.
  5. Install the halfshaft to the vehicle and reconnect the negative battery
    cable.






Check the CV-boot for wear
tccs7030.jpg








Removing the outer band from the CV-boot
tccs7031.jpg








Removing the inner band from the CV-boot
tccs7032.jpg








Removing the CV-boot from the joint housing
tccs7033.jpg








Clean the CV-joint housing prior to removing boot
tccs7034.jpg








Removing the CV-joint housing assembly
tccs7035.jpg








Removing the CV-joint
tccs7036.jpg








Inspecting the CV-joint housing
tccs7037.jpg








Removing the CV-joint outer snap ring
tccs7038.jpg








Checking the CV-joint snap ring for wear
tccs7039.jpg








CV-joint snap ring (typical)
tccs7040.jpg








Removing the CV-joint assembly
tccs7041.jpg








Removing the CV-joint inner snap ring
tccs7042.jpg








Installing the CV-joint assembly (typical)
tccs7043.jpg




prev.gif next.gif

Oct 07, 2010 | 2002 Chevrolet Silverado 2500HD

1 Answer

Ford fusion front end noise when doing tight three point turn or manovers


popping noise when turning is usually caused by worn CV joints. Inspect CV boots for tears. Torn boot will allow dust to get in and cause wear. If boot is torn, replace CV joint or entire shaft (usually easier). If boot is not torn, grab shaft next to each CV joint and see how much movement you can cause in the joint. If one CV moves more than the other three, that one is probably bad.

Aug 23, 2010 | 2005 Ford Fusion

1 Answer

1997 Pathfinder How do you replace the left outer cv boot?


How to Replace a CV Boot
( DIY Complexity: Hard / Time: 3.2 hours )

Parts:
1. CV Boot
2. CV Boot Clamp Kit

Tools:
1. Mallet Hammer
2. 3/8 in. Drive Ratchet
3. Combination Wrench Set
4. Floor Jack
5. Flashlight
6. Flat Head Screwdriver
7. Socket Set
8. Tire Iron

Steps:
Step 1 Secure the vehicle on a level surface, making sure the vehicle will not roll or lean too much when jacked up.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 Lift up the front of the vehicle using a jack.
o Tip: Using an aftermarket floor jack, instead of the original equipment (OE) jack, can make the job easier and safer. Verify the condition of the floor jack before use.

Step 3 Secure the vehicle with jack stands on both sides for safety before starting any work. The pinch welds and the frame are the two best locations. Do not rely on the jack to hold the vehicle up while working.
o Tip: Try to find a flat, level, and strong surface to put the jack stands.

Step 4 Find the correct size socket and large ratchet or tire iron and turn the wheel lug nuts counter clockwise. Remove the front wheels.
o Tip: It is a good idea to try and break the lug nuts free before you jack the wheels off the ground. This way they you will not spin the front wheels or put stress on the transaxle.
o Tip: Lug nuts fasten the wheel to the hub and may be on very tight. To gain more leverage, use a breaker bar to loosen the nuts.

Step 5 Inspect the CV boot for damage.
o Tip: The CV joint may be worn if the boot is damaged. Thoroughly inspect the CV joint assembly before installing the new boot. If the CV joint is damaged, replace the entire CV joint axle assembly.

Step 6 Mark the axle for installation reference. Remove the CV joint axle assembly.

Step 7 Using a bench vise, hold the shaft of the CV joint secure so that you can separate the CV joint from the shaft. Remove the CV boot clamps.

Step 8 Slide the CV boot off the outer CV joint.

Step 9 Using a rubber mallet, knock the CV joint off of the axle shaft.

Step 10 Remove the old boot from the CV axle shaft and wipe off any old grease. Clean the sealing surface on the CV joint.

Step 11 Fill the CV joint with grease and get it ready to slide back onto the shaft.

Step 12 Slide the new boot onto the shaft but do not tighten the inner clamp yet. Install a new retaining clip before putting the joint and axle together.

Step 13 Slide the CV joint back onto the axle shaft completely.

Step 14 Pack the boot with grease and slide the boot over the CV joint housing. Secure the boot with new clamps.

Step 15 Install the CV joint and axle back into the vehicle in the reverse order that it was removed.

Step 16 Mount the wheel back onto the hub assembly.

Step 17 Tighten lug nuts in a star pattern and torque to suggested manufacturer specifications in the vehicle owner’s manual.

Step 18 Remove jack stands.

Step 19 Lower vehicle with jack until it is securely on the ground.

Step 20 Drive the vehicle to make sure that any noises are no longer present and that there are no indications of wearing parts. Before road testing, visually inspect the area you have worked on to make sure everything is tightened and assembled properly.

Hope help with this (remember rated and comment this help).

Mar 12, 2010 | 1997 Nissan Pathfinder

1 Answer

How do I change the CV joints on a 1.8TD Ford Escort P reg


Hi mate

With the driveshaft removed from the vehicle.

Undo the the retaining straps on the CV boot.

Pull the CV boot up the driveshaft a little way, enough so you can clean all the old grease away.

Now look into the CV joint an locate the circlip that locks the CV to the driveshaft.

Now put the driveshaft into a vice with the CV joint facing downwards.

Now open the circlip and at the same time strike the CV joint. You can do this with a ballpin hammer if you are scrapping the CV joint. You can get a helper to stike the CV joint with a hammer while you keep the circlip open.

This will release the CV joint form the drive shaft.

Now clean the driveshaft of any old grease and fit a new CV boot if needed.

Now reverse the driveshift in the vice and fit the new CV joint. It will tap on with no trouble but do not damage it. Test it is on by trying to pull it off with your hands.

Now fill it with new grease.

Fit the CV boot to the CV joint and secure it to the CV joint.

Now it is ready to refit to your vehicle.

I trust this solves the problem for you.

Ray


Sep 08, 2009 | 1998 Ford Escort

1 Answer

Where can I find the rubber seals for the ball joints that houses the cv joints on the front axle for a nissan safari ldv '89 model


If you are refering to those corrugated rubber boots, it is highly recommended to replace those CV shafts as the dirt and moisture contamination is not a good thing in CV joints. Dirt and moisture are the leading causes of CV shaft failures. You can by the boots as a repair boot and those wrap around the CV shaft/joint area and bolt together. If you are talking about the little rubber boots on the ball jonts themselves at the end of a steering link, those boots are not sold individually. They only come with new Ball joint assemblies.

Aug 04, 2009 | 1987 Nissan Pickup

1 Answer

Cv boot clamp came off somehow from the outer hub assembly


athere is a snap ring within the CV joint the nedds to be spread OPEN to release CV joint from axle, Once CV is cleaned and repacked with grease rintall onto axle by again spreading apart clamp. Prior to installing CV joint slide NEW CV joint boot onto axle, Cleanly intall add'l grrease and reinstall CV boot.

Apr 04, 2009 | 1996 Buick Century

4 Answers

Turning left makes a knocking noise


HI. The first thing i recommend is to check the power steering fluid. If its at a proper level, this may be a more serious issue with the steering rack(assembly). A common issue that will cause the knocking during the turn sequence can be the CV boot and joint assembly. the CV boot merely holds the grease around the CV joint itself. The knocking sound is probably from the CV joint. If the boot fails, the joint runs dry and shortly after that, the joint fails. Preventive maintenance would be to inspect the boots and replace if damaged before the joints are damaged.

Please rate and god bless.

Mar 25, 2009 | 1997 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...