Question about 1998 Chevrolet K1500

1 Answer

How do i remove the front driveshaft from my 1998 chevy k1500? there is a u-joint on each end of the driveshaft & i have removed the clips from around the u-joint but the driveshaft is too tight to come out?

Posted by on

  • rob Oct 16, 2010

    are the u-joints at both ends of the front driveshaft pressed in or what? i dont understand how the front driveshaft comes out from between the transfer case and the front differential? i have removed the retaining clips on each side of the yoke but the driveshaft wont come out?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Will not go in 4 wheel drive

Posted on Oct 18, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove axle from front of 1998 windstar


  1. Raise and support the vehicle safely.
  2. Remove the front wheels.
  3. Insert a steel rod into the brake rotor to prevent the rotor from turning and loosen the axle wheel hub nut. Discard the nut.
  4. Remove the ball joint-to-front wheel knuckle retaining nut. Drive the bolt out of the front wheel knuckle using a punch and hammer.
  5. Remove the front brake anti-lock sensor and position it out of the way.
  6. Separate the ball joint from the front wheel knuckle using a prybar. Position the end of the prybar outside of the bushing pocket to avoid damage to the bushing.
Use care to prevent damage to the front wheel driveshaft joint boot.
  1. Remove the stabilizer bar link at the front stabilizer bar.
Make sure the CV-joint puller does not contact the transaxle shaft speed sensor. Damage to the sensor will result.
  1. Install a CV-Joint Puller (T86P-3514-A1) or equivalent between the inboard CV-joint and the transaxle case.
  2. Install a CV-Joint Extension (T86P-3514-A2) or equivalent into the puller and hand-tighten.
  3. Using an impact slide hammer, remove the driveshaft from the transaxle.
Do not allow the front wheel driveshaft and joint to hang unsupported. Damage to the front wheel driveshaft joint may result. Do not wrap wire around the front wheel driveshaft joint boot. Damage to the boot may result.
  1. Support the end of the driveshaft and joint assembly by suspending it from the chassis using a length of wire.
Never use a hammer to separate the outboard front wheel driveshaft joint from the wheel hub. Damage to the outboard front wheel driveshaft joint threads and internal components may result.
  1. Separate the outboard front wheel driveshaft joint from the wheel hub using a Front Hub Remover/Replacer (T81P-1104-C) or equivalent. Make sure the hub remover adapter is fully threaded onto the hub stud.
Do not move the vehicle without the outboard CV-joint properly installed, as damage to the bearing may occur.
  1. Remove the front wheel driveshaft and joint assembly from the vehicle.
To install:
Do not reuse the retainer circlip. A new circlip must be installed each time the inboard CV-joint stub shaft is installed into the transaxle differential.
  1. Install a new retainer circlip on the inboard CV-joint stub shaft by starting one end in the groove and working the retainer circlip over the inboard shaft housing end and into the groove. This will avoid overexpanding the circlip.
A non-metallic mallet may be used to aid in seating the retainer circlip into the differential side gear groove. If a mallet is necessary, tap only on the outboard CV-joint stub shaft.
  1. Carefully align the splines of the inboard CV-joint stub shaft housing with the splines in the differential. Exerting some force, push the inboard CV-joint stub shaft housing into the differential until the retainer circlip is felt to seat in the differential side gear. Use care to prevent damage to the inboard CV-joint stub shaft and transaxle seal.
  2. Carefully align the splines of the outboard front wheel driveshaft joint with the splines in the wheel hub, and push the shaft into the wheel hub as far as possible.
  3. Temporarily fasten the front disc brake rotor to the wheel hub with washers and two lug nuts. Insert a steel rod into the front disc brake rotor and rotate clockwise to contact the front wheel knuckle, to prevent the front disc brake rotor from turning during front wheel driveshaft and joint installation.
A new front axle wheel hub retaining nut must be installed.
  1. Manually thread the front axle wheel hub retaining nut onto the outboard CV-joint stub shaft housing as far as possible.
A new bolt and nut must be used to connect the front suspension arm to the knuckle.
  1. Connect the front suspension lower arm to the front wheel knuckle. Tighten the nut and bolt to 40-55 ft. lbs. (54-74 Nm).
  2. Install the front brake anti-lock sensor.
  3. Connect the front stabilizer bar link and tighten to 35-45 ft. lbs. (47-65 Nm).
Do not use power or impact tools to tighten the hub nut.
  1. Tighten the front axle wheel hub retaining nut to 157-212 ft. lbs. (213-287 Nm).
  2. Install the front wheels and lower the vehicle.
  3. Using the recommended type of fluid, fill the transaxle to the proper level.

Jul 07, 2014 | 1998 Ford Windstar

1 Answer

Vibration rumbling coming from front end of a 1997 chevy blazer 4 wd


You still have hubs, and the front driveshaft. On some models the front driveshaft can be removed leaving the pinion forks/ ring in place. Some other Transfer cases may use an output shaft thats like the tailshaft on an automatic. This style could leave a gapping hole when you remove the front driveshaft.

Tires are a problem once a wear pattern is embedded in the tread. Sometimes a front to back rotation will reduce noise.

A caliper could be stuck skipping over a turning rotor.

Oct 31, 2012 | Cars & Trucks

1 Answer

How do I remove the front driveshaft on a 2003 TrailBlazer?


there are two types, one will use a slide type joint rubber insul, and will have small bolts holding it to transfer case. the other type will have no bolts and pops in to transfer case, to remove this type you use a small pry bar and pop it out like a cv axle out of transmission, it uses a c clip to lock itself in, wedge pry between transfer case and joint and give a pull.

Oct 14, 2012 | 2003 Chevrolet TrailBlazer

1 Answer

Trying to change u-joints front and rear on driveshaft? any advice or assistance would be appreciated..


firt you will need to remove the drive shaft by un bolting it from the rear end. U joints are held in with a small clip on some, others have a cover which is bolted on over the end of the u joint. once you remove the clips or cover drive out u joint with a hammer replace with new one insert clips or cover install driveshaft greese all fittings.

Sep 01, 2011 | 2003 Ford F150 Regular Cab

1 Answer

I have a 1998 chevy 1500 it has a viberasion at about 65 the drive shaft has a little play in it were it comesout of the transfercase how can i fix it


Alittle play is normal, what i would do is remove the driveshaft and check the ujoints, a bad or frozen joint will cuase a vibration, this is a common problem i would start with that and maybe you will find a bad ujoint. good day.

Aug 28, 2011 | 1998 Chevrolet K1500

1 Answer

How to replace bearing in a 1991 chevy 1500 4x4 rear axel at driveshaft?


To replace pinon bearing you need to pull wheels and the brake drums off next pull cover off the back of the rear end (make sure you have a drain pan under rear end) next turn dive shaft till you see a small bolt remove bolt pull center pin out push axle in pull c clips out pull axels out remove four bolts holding ring and spider gears remove gears assembly next remove drive shaft remove bolt from pinon push pinon in remove seal and bearing

Jun 27, 2011 | 1991 Chevrolet K1500

1 Answer

Repear the drivesaft universal joint


Hello, this is the type of problem I repaired as a teenager in the 60's. The U-joints have not changed and the same methods are used today. You start out by marking the driveshaft on either side of the U-joint with something durable like paint. This is done to preserve the balance in the driveshaft when you reassemble it. You line up the paint marks when you put in the new joint.

To disassemble the joint you will need to remove the driveshaft. The end by the Differential will have standard head bolts or Torx head bolts. When the driveshaft is unbolted you drop it down and pull it out of the end of the Transmission or Transfer case. The driveshaft will slide out and you may lose a small amount of transmission fluid. The seal in the transmission is usually reusable, always coat the driveshaft flange with a little lube to insure the seal does not grab and tear on reassembly.

Now you are looking at the removed driveshaft. There are "C" clips or "Snap-rings" in front of the "Caps" on the U-joint. You must remove these clips. Then position the driveshaft between blocks of wood or a good sized Vise to get clearance below the joint. Now you will fit a socket from your toolbox that just fits into the hole where you removed the "Snap-ring".

At this point you will pound the "Cap" of the U-joint through the stationary flange which formerly held the U-joint. The U-joint will be driven through the fixture and you can swing it out. To reassemble, care must be taken to keep both "Caps" on the new joint. You may clean and grease the fixture to aid in sliding in the new parts.

Should your "Caps" come off the new part, stop, and verify the needle bearings have not moved. A heavy wheel bearing grease will hold the needle bearings in place. Then install the "Snap-rings" and note that the paint lines on the driveshaft still line up.

I hope my solution has been very helpful to you. The only extra item I can mention is some U-joints have 2 different sized "Caps" on them. If the U-joint does not seem to fit into the fixture the U-joint may need to install with the second pair of "Caps" fitting into the fixture instead of the way you have yours turned.

Jan 09, 2011 | 1999 Ford Explorer

1 Answer

Do I have to remove the control arm to replace the half shaft on a 2005 Ford Freestar?


no, here's the procedure for 2002 windstar, should be similar. please rate, thanks.

NOTE: This procedure applies to both the LH and RH halfshaft assemblies.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the front wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Insert a steel rod in the brake disc to prevent the halfshaft from turning while removing the front axle wheel end nut.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The front axle wheel end nut is a torque prevailing design nut. Do not reuse it.
    Remove the nut and washer.
    • Remove the steel rod in the brake disc.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Remove or tape the brake pads to prevent them from falling out of the anchor plate.
    s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent damage to the brake hose, do not allow the disc brake caliper to hang suspended from the hose.
    Remove the bolts and position the disc brake caliper aside.
  1. Remove the front brake anti-lock sensor harness from the clip.
  1. Remove and discard the nut and bolt.
    • If necessary, use a punch and a hammer to drive the bolt out of the knuckle.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Position the end of the pry bar outside the bushing pocket to avoid damage to the bushing.
    s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the front wheel driveshaft joint boot (3A331).
    Separate the front suspension lower arm from the knuckle.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never use a hammer to separate the front wheel driveshaft joint (3B413) from the wheel hub. Damage to the joint threads and internal components can result.
    Using the special tool, press on the front wheel driveshaft joint until it is loose in the wheel hub.
  1. Rotate the front wheel knuckle rearward, while pulling it outward at the bottom and remove the front wheel driveshaft joint from the wheel hub.
  1. Using a pry bar, separate the inboard CV joint housing assembly (3B436) (3B437) from the transaxle.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the differential seal.
    Remove the halfshaft assembly with both hands.
Installation
  1. Lubricate the differential seal.
    • Use MERCON® V Automatic Transmission Fluid XT-5-QM or equivalent meeting MERCON® V specifications.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Install a new circlip every time you remove the halfshaft from the vehicle.
    On the RH side halfshaft only, install a new circlip in the groove in the inboard CV joint stub shaft.
    • Start one end in the groove and work the circlip over the shaft and into the groove. This will prevent the circlip from over-expanding.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the inboard CV joint housing assembly and the differential seal.
    NOTE: If necessary, use a non-metallic mallet to aid in seating the circlip in the differential side gear groove (RH) or inboard CV joint housing (LH). Tap only on the outboard front wheel driveshaft joint.
    Align the inboard CV joint housing splines with the differential side gear splines (RH) or output shaft splines (LH), and push the inboard CV joint housing assembly inward until the circlip seats in the differential side gear (RH) or inboard CV joint housing (LH).
  1. Align the front wheel driveshaft joint splines and the wheel hub splines, and push the joint into the wheel hub as far as possible.
  1. Install the washer and the old nut. Using the old nut, seat the front wheel driveshaft joint in the hub. Remove the old nut and discard it.
  1. Connect the suspension lower arm to the knuckle.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Install a new bolt and nut.
    Install the new bolt and nut.
  1. Insert a steel rod in the brake disc to prevent the halfshaft from turning while installing the new front axle wheel end nut.
  1. Apply a small patch of Loctite 242 or equivalent meeting Ford specification WSK-M2G351-A5 to the last five front wheel driveshaft joint threads.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Install and tighten the new front axle wheel end nut to specification in a continuous rotation. Stopping the rotation during installation will cause the nylon lock to set incorrectly. This will cause incorrect torque readings while tightening the nut, and lead to bearing failure. Always install a new front axle wheel end nut after loosening the nut, or when the nut has not been installed to specification in a continuous rotation.
    Install and tighten the new nut to specification in a continuous rotation.
    • Remove the steel rod from the brake disc.
  1. Position the disc brake caliper and install the bolts.
  1. Install the front brake anti-lock sensor harness in the clip.
  1. Install the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Lower the vehicle.
  1. Check and, if necessary, fill the transaxle to the correct level with the specified fluid. For additional information, refer to Section 307-01 .

Nov 15, 2009 | 2005 Ford Freestar

2 Answers

Need to change cv outer boot on mazda ba 94 model.


it just pulls out. it hasa circlip that holds it in on driver side. which side?

here's an escort, should be similar. note step 17

Removal
  1. Raise and support the vehicle.
  1. Remove the lug nuts (1012) and the front wheel and tire assembly.
  1. Remove the front fender splash shield bolts and the front fender splash shields (16103) .
  1. Use a small cape chisel to carefully raise the staked portion of the front axle wheel hub retainer (3B477).




  1. Remove the front axle wheel hub retainer and discard it.
  1. Remove the cotter pin and the tie rod end nut from the tie rod end (3A130). Discard the cotter pin.




  1. Use an appropriate tie rod end remover to separate the tie rod end from the front wheel knuckle (3K186).




  1. Remove the ball joint bolt and the ball joint bolt nut.




  1. Carefully pry down on the front suspension lower arm (3078) to separate the front suspension lower arm ball joint (3050) from the front wheel knuckle.




  1. Pull outward on the front wheel knuckle (3K185). Carefully pull the front wheel driveshaft and joint from the front wheel knuckle and position it aside.




  1. NOTE: Removal of the LH front wheel driveshaft and joint (3B437) requires removal of the transmission support crossmember (6A023) to allow access with a pry bar. If the LH front wheel driveshaft and joint is being removed, continue with step 11. If the RH front wheel driveshaft and joint is being removed, continue with step 15.

    Support the transaxle with a transaxle jack or equivalent.
  1. Remove the four transaxle mount-to-rear engine support nuts.




  1. Remove the two rear engine support nuts at the rear of the transmission support crossmember.
  1. While supporting the rear of the transmission support crossmember remove the two rear engine support bolts. Remove the transmission support crossmember.




  1. Position a drain pan under the transaxle.
  1. Insert a pry bar between the front wheel driveshaft and joint and the transaxle case.
  1. stf~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Extreme care must be taken to ensure that the pry bar does not damage the transaxle case, the transaxle oil seal, the front wheel driveshaft and joint, or the front wheel driveshaft joint boot (3A331).
    Gently pry outward to release the front wheel driveshaft and joint from the differential side gears (4236).




  1. Remove the front wheel driveshaft and joint.




  1. stf~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: When the LH and RH front wheel driveshaft and joint assemblies are removed, Transaxle Plugs T88C-7025-AH must be inserted to prevent the differential side gears from becoming mispositioned. If the gears become misaligned, the differential will have to be removed from the transaxle to align the gears.
    If both front wheel driveshaft and joints were removed, install Transaxle Plugs T88C-7025-AH in the differential side gears.
  1. Remove and discard the driveshaft bearing retainer circlip (3Z498).

Oct 03, 2009 | 1994 Mazda 323

1 Answer

Fuel pump hose fittings


is there plastic clips that hold the lines if there is not there is a tool that you put in the end of the line that releases the line

Dec 14, 2008 | 1998 Chevrolet K1500

Not finding what you are looking for?
1998 Chevrolet K1500 Logo

627 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...