Question about 2000 Mercedes-Benz S-Class

1 Answer

How to replace ignition key battery - 2000 Mercedes-Benz S-Class

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 229 Answers

Remove mettle key blade from you key, for remove key blade you have to slide lock witch is sitting in top of your key, near the mettle key you can see small sliding switch, remove mettle key, then have a look not in the deep hole witch is mettle key was insert but left of the mettle key remove sliding switch small grow witch is mettle key head ware sitting in, if you have a good look small gray sliding part is there, you have to use mettle key blade to press it and press it backward of key when you press it you can see it's moving, keep that moving part press by mettle key and pull out the key head, then you can see battery in that part witch is came out from key before remove the battery keep in mind negative and positive it have mention on battery replace battery and jest push key head in to the key til lock insert the right way , is this information helped you? please leave a comment.

Posted on Oct 17, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ignition Key Replacement


disconnect the battery and connect it all up and leave battery off overnight. Put the key in the ignition but not turned on. Connect the battery in one bang, wait 15 minutes for the transponder chips in key and ignition lock to be paired by the ECM.

Jun 28, 2017 | 2002 Jaguar S-Type

1 Answer

2003 range rover hse new battery won't hold charge and key is stuck in ignition


was the key stuck in the ignition before you change the battery? Is it the right key or it a fresh cut key

Dec 27, 2012 | 2003 Land Rover Range Rover

1 Answer

1996 Renault Clio Club 1.2 Petrol. Batteries replaced in ignition key. Unable to start car. Battery ok, engine turns over ok but will not fire up. Prior to replacing the batteries there was no proble


You have either put the batteries in wrong or you have lost programming, see the dealer if you are 100% sure the new batteries where not installed incorrectly. What about the spare key???

Sep 04, 2012 | Cars & Trucks

1 Answer

Kia sedona doors chime even when key is NOT in the ignition... then runs down battery


have u tried replacing the ignition switch.. sounds like that's the problem..

Apr 29, 2012 | 2002 Kia Sedona

1 Answer

I have a 2001 ford expediton 4.6 4wd..2 days ago I went to turn off my car and the radio and that beeping sound when the key is in the ignition when the door is open stayed on and wouldnt go off. I turned...


Not the Key but the ignition itself. Replace teh ignition module where the key is inserted to start the vehicle and that should resolve the issue.

Jul 11, 2011 | 2001 Ford Expedition

1 Answer

My battery went dead in my 95 buick skylark, now the key wont even turn


The battery going dead has nothing to do with the key now not turning, however, the key not turning properly could have caused the dead battery if the ignition switch did not turn off all the way. Anyway, if the key won't turn, you most likely need to replace the ignition lock cylinder. The battery is a whole different issue. It could be a problem with the ignition switch, or it could just be time to replace the battery.

Feb 27, 2011 | Buick Skylark Cars & Trucks

2 Answers

Everything is locked up. Can't get the key out of the ignition and there is no power to anything. Any suggestions on what to do?


grab the staring wheel you should be able to move a little from side to side,, while moving the wheel try to turn the key back,,

Apr 19, 2010 | 2003 Chevrolet TrailBlazer

1 Answer

Flashing alarm light after battery change. Car wont start,


System operation
System arms 5 seconds after switching ignition OFF. Switch ignition ON. Ensure clock LED illuminates for 3-5 seconds. If LED flashes rapidly at regular intervals for approximately 1 minute, then flashes at irregular intervals: Key code not recognised. Remove key and try again.
Programming
When
System malfunction: LED illuminates for 1 minute, then flashes at irregular intervals. Key(s) added or replaced.
NOTE: Replacement keys MUST have blue mark. Keys with red mark are NOT compatible with this system.
How
NOTE: Programming method using vehicle keys can be deactivated using diagnostic equipment.
Obtain 2 programmed keys (A and B). Insert key A into ignition switch. Turn ignition switch to position II. Wait 1 second. Switch ignition OFF. Remove key A. Insert key B into ignition switch within 5 seconds. Turn ignition switch to position II. Wait 1 second. Switch ignition OFF. Remove key B. Within 10 seconds: Insert key to be programmed into ignition switch. Turn ignition switch to position II. Wait 4 seconds. Switch ignition OFF. Wait 5 seconds. Start engine. If engine does not start and clock LED flashes: Switch ignition ON. Wait at least 20 seconds. Switch ignition OFF. Repeat programming procedure. Repeat above procedure to program remaining keys. Keys can also be programmed using diagnostic equipment

Mar 08, 2010 | 2000 Ford Focus

1 Answer

Why won't the key turn in the ignition battery replaced last week


it might need reprogramming depends how long u took to replace the battery.

Jan 04, 2009 | 2002 Mercedes-Benz C-Class

2 Answers

How to get key out that is stuck in ignition


Remove steering column shroud(cover)and tap ignition barrel with small hammer while twisting key backwards and forwards,also turn steering wheel backwards and forwards sometimes this is enough to release key as the locking pins in barrel and the steering lock pin do sometimes jam.You will have to remove steering column shroud to replace ignition barrel if tapping/hitting it doesnt work anyway so its not a wasted effort.Good luck,let me know how it works out

Nov 12, 2008 | 2003 Oldsmobile Bravada

Not finding what you are looking for?
2000 Mercedes-Benz S-Class Logo

858 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

yadayada
yadayada

Level 3 Expert

77499 Answers

Joseph Prosser

Level 3 Expert

772 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...