Question about Dodge Durango

2 Answers

On a 1999 dodge durango 5.9 the lower 02 sensor what the colors of the wires mine got cut and i want to rewire it please

Posted by on

  • 2 more comments 
  • JOE Oct 16, 2010

    THAT I UNDERSTAND BUT I NEED THE DODGE COLOR CODE SO I CAN WIRE THEM
    RIGHT

  • JOE Oct 16, 2010

    IS THERE A WAY I CAN GET THE CORRECT DODGE O2 SENSOR WIRE COLORS LIKE WHAT GOES TO NEW O2 SENSOR LIKE BLACK GOES TO WHAT AND BLUE GOES TO WHAT SO ON AND SO ON

  • JOE Oct 16, 2010

    I HAVE A 1999 DODGE DURANGO 5.9 I NEED TO REPLACE THE BANK2 O2 SENSOR BUT THE PERSON I PURCHASED IT FROM CUT THE WIRES. WHAT IS THE CORRECT WIRE COLORS TO THE GRAY,BLACK AND 2 WHITE WIRES PLEASE HELP

  • JOE Oct 17, 2010

    i change the o2 sensor then it said upsteam need to be replaced. ok both done now after erasing the codes and running for 30min it says down stream 02 sensor high voltage

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,926 Answers

If you look at the connector for the other O2 sensor and take notice of how the wires are placed in this factory connector, you can then match the aftermarket connection wire placement to the O2 you need to wire up.

Posted on Oct 16, 2010

  • GetMeOttaHere Oct 18, 2010

    Ok, the downstream O2 is stuck at around the 1.3 volts and is sensing a rich command to the fuel system. The could be caused by a faulty o2 sensor, poorly tuned or running engine, exhaust leak or defect catalytic converter.

×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 22,219 Answers

Just look at the existing colours ,if four wires then their will be two whites which go to the other two whites ,and they can be connected either way around ,then their is a grey and a blue ,colour of cables vary acording to manufacturer but their will be two the same and they can go either way around

Posted on Oct 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am trying to hook up pioneer deh425 car stereo to my 99 dodge durango please I need wiring color codes for both thank you


go to a radio shack or like store and get a adapter plug to match your new unit , that way you don"t have to cut no wires and its a piece of cake to just plug in this thing will plug in to the dodge plug and the other end plugs in to your new unit

Nov 18, 2015 | 1999 Dodge Durango

1 Answer

My 2003 Durango has an after market trailer hitch on which the wiring converter has literally exploded leaving me with no tail lights and fried wire ends on the vehicle side of the converter. Since I am...


You should not have to rewire anything.
Hitch wires are just "pig-tailed" on to the original vehicle wiring. Just cut off the hitch wires cleanly and tape the cut end.
You have probably burned out the stop and tail lamp fuses also. Read you owner manual for fuse location.
Please rate is answer by checking the "Hands" below. Thanks j

Feb 09, 2011 | 2000 Dodge Durango

1 Answer

Engine cuts out and gauges drop


I think the problem is on the harness connector going into the computer. I am having the same problem myself. I have replaced 3 computers and now it is doing it again. Dodge dealer just wants to continue replacing computers. I am going to a salvage yard to find a 99 durango and cutting out the wiring harnesses 12" from computer and splicing all the wires together on mine. It is about 75 wires, so this will take some time. Once completed I will wrap all harnesses with aluminum wire wrap to deflect heat off harness connections going into computer. This is part of the cause for the failure along with poor connecting design by Chrysler.

Jun 30, 2010 | 1999 Dodge Durango

1 Answer

How do i remove the factory stereo out of my 2002 dodge durango and replace it with an aftermarket stereo and also getting the speaker to work if they are amped


take the plastic thing off that goes all the way around the guages or w.e. then ther should b 2 bolts on the front of the stereo take them out. take out the radio n unconnect wires. then get a wire kit n plug it in and hook it up. if the speakers dont work either get new ones or rewire them using all different wires.

Dec 29, 2009 | 1999 Dodge Durango

2 Answers

Firing order for spark plug wires for a1999 dodge durango 5.2 please show me a diagram.


1999 Dodge Truck Durango 4WD 5.2L SFI 8cyl

e8dbcd9.jpg
5.2L and 5.9L Engines Firing Order: 1-8-4-3-6-5-7-2 Distributor rotation: Clockwise

I hope help you with this. Good luck (remember rated this help).

Oct 09, 2009 | 1999 Dodge Durango

1 Answer

Need a wiring Diagram for a 1999 Dodge Durango so i can install a remote start system. Or what colors I need to look for.


Most auto parts stores such and advance auto parts and autozone sell repair manuals. I prefer the Haynes manuel wich has the wireing diagrams printed in the back of the book and acuratley tell each color code

Aug 03, 2009 | 1999 Dodge Durango

2 Answers

Cylinder Layout V8 5.9 L Magnum Dodge


drivers side plugs from front of engine to rear are cylinder numbers 1...3...5...7
passenger side front to rear 2...4...6...8..
fiing order 1..8..4..3..6..5..7..2..

Sep 07, 2008 | 1999 Dodge Durango

1 Answer

1999 dodge durango fan motor replacement


  1. Remove right side scuff plate.
  2. Pull back carpet.
  3. Disconnect blower motor wiring connector.
  4. Remove blower motor retaining screws, and lower blower motor assembly from unit housing.

Jun 27, 2008 | 1999 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...