Question about 2005 Honda Pilot

1 Answer

How to replace a heater core - 2005 Honda Pilot

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 6,826 Answers

Heater Core Removal & Installation Front To Remove:

  1. Make sure you have the anti-theft codes for the audio and the navigation system, and then write down the audio presets.
  2. Disconnect the negative cable from the battery.
  3. From under the hood, disconnect the heater valve cable from the heater valve. Turn the heater valve arm to the fully opened position.
  4. When the engine is cool, drain the engine coolant from the radiator.
  5. Disconnect the inlet heater hose and the outlet heater hose from the heater core.
  6. Remove the mounting nut from the heater unit. Take care not to damage or bend the fuel lines, the brake lines, and related parts.
  7. Remove the dashboard.
  8. Remove the evaporator.
  9. Remove the mounting bolts and remove the heater unit. Front heater unit how to replace a heater core - honda-10-00-4128.gif

  10. Remove the self-tapping screws and the clamp.
  11. Carefully pull out the heater core so you don't bend the inlet and outlet pipes.
Front heater core honda-10-00-4129.gif

To Install:
  1. Using care, install the heater core to the heater unit and secure.
  2. Using care, install the heater unit and tighten mounting nuts and bolts to 7 ft-lb (10 Nm).
  3. Install the evaporator.
  4. Install the dashboard.
  5. Connect the inlet heater hose and the outlet heater hose to the heater core.
  6. Connect the heater valve cable to the heater valve.
  7. Refill the cooling system with engine coolant.
  8. Adjust the heater valve cable.
  9. Make sure that there is no coolant leakage.
  10. Make sure that there is no air leakage.
  11. Connect the negative battery cable.
  12. Perform the power window control unit resetting procedure.
  13. Enter the anti-theft codes for the audio and the navigation system, and then enter the audio presets.
Rear To Remove:
NOTE: The rear blower motor, the rear heater core, the blower screen, the rear blower resistor (heating/air conditioning system) and the rear power transistor (climate control system), the rear air mix control motor (climate control system) , the rear mode control motor and the rear expansion valve can be replaced without removing the rear heater-A/C unit.
  1. Remove the self-tapping screws and the clamp, and then remove the bolts and the rear evaporator lines with the rear expansion valve. If necessary, remove the rear expansion valve. Use a second wrench to hold the other fitting on the valve so the rear evaporator lines won't twist. Leave the first fitting loosely connected so you can use it to hold the valve while you loosen the second fitting.
  2. Remove the rear heater hoses.
  3. If necessary, remove the rear blower motor, the rear heater core, the blower screen, the rear blower resistor (heating/air conditioning system), the rear power transistor (climate control system), the rear air mix control motor and the rear mode control motor.
  4. Remove the self-tapping screws and the lower housing.
  5. Remove the self-tapping screws, and carefully separate the left upper housing from the right upper housing. Remove the rear heater core.
Rear evaporator assembly honda-10-00-4116.gif

To Install:
  1. Replace the rear heater core.
  2. Attach the heater hoses.
  3. Make sure no air is leaking from the left upper housing and the right upper housing fitting and from the upper housings and the lower housing fitting.
  4. Before reassembly, make sure that the rear air mix control linkage and door move smoothly without binding.
  5. Before reassembly, make sure that the rear mode control linkage and door move smoothly without binding.
  6. Reassemble the housing.
  7. After reassembly, make sure the rear air mix control motor runs smoothly.
  8. After reassembly, make sure the rear mode control motor runs smoothly.
  9. Refill the cooling system and make sure that there is no coolant leakage.
prev.gif next.gif

Posted on Oct 16, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can hear water when running.


can be clogged heater core,try inspecting the heater core.

HEATER CORE REPLACEMENT


If its clogged it can be cleared with the use of Garden hose p[ump.The water has to be turn into the heater hose line and then water has to be removed out via the pump.

==========

For complete step by step procedure,refer heater core flushing and other help links mentioned below.


======

Click the link below:-----

------------

How to Flush Heater Core?

http://schematicsdiagram.blogspot.com/2011/12/how-to-flush-heater-core.html

------------

How to replace heater core on Chevy Astro?

http://schematicsdiagram.blogspot.in/2012/03/how-to-replace-heater-core-on-chevy.html

-----------

Replacing heater core for grand marque?

http://schematicsdiagram.blogspot.in/2012/03/replacing-heater-core-for-grand-marque.html

------------

How to replace heater core for All car models?

Click the link below:---

http://technoanswers.blogspot.com/2011/11/how-to-replace-heater-core-for-all-car.html

-------------

How to replace heater core on Buick Regal?

http://howtobyme.blogspot.in/2012/02/how-to-replace-heater-core-on-buick.html

-------------

How to Remove Heater Core on 2008 Honda Odyssey?

http://howtobyme.blogspot.com/2011/12/how-to-remove-heater-core-on-2008-honda.html

------------

Honda Heater Core Replacement?

http://howtobyme.blogspot.com/2011/12/honda-heater-core-replacement.html

------------

How to replace heater core on Mitsubishi magna?

http://technoanswers.blogspot.in/2012/02/how-to-replace-heater-core-on.html

-----------

How to replace heater core on Mitsubishi eclipse?

http://technoanswers.blogspot.in/2012/02/how-to-replace-heater-core-on_10.html

=========

These will help.

Thanks.

Nov 28, 2012 | 2000 GMC Jimmy

1 Answer

Can you bypass the heater core


For heater core replacing procedure. I suggest you to go through this related help links.Its all complete step by step procedure: ----How to replace heater core for All car models?

Click the link below: ---

http://technoanswers.blogspot.com/2011/11/how-to-replace-heater-core-for-all-car.html

--------------
How to Flush Heater Core?

http://schematicsdiagram.blogspot.com/2011/12/how-to-flush-heater-core.html

---------------
How to Remove Heater Core ?

http://howtobyme.blogspot.com/2011/12/how-to-remove-heater-core-on-2008-honda.html
Heater Core Replacement?

http://howtobyme.blogspot.com/2011/12/honda-heater-core-replacement.html

------------
To replace heater core?http://technoanswers.blogspot.in/2012/02/how-to-replace-heater-core-on.html------

How to replace heater core?http://technoanswers.blogspot.in/2012/02/how-to-replace-heater-core-on_10.html
How to replace heater core on Buick Regal?

http://howtobyme.blogspot.in/2012/02/how-to-replace-heater-core-on-buick.html
----------This will help.Thanks.

Feb 04, 2012 | 2000 Lincoln Town Car

4 Answers

Heater core leaking through floor vents.


Bad heater core you will need to replace it. About a 2 hour job, very easy to do:


Remove the HVAC module assembly. Refer to HVAC Module Assembly Replacement.
Remove the HVAC filter cover.
Remove the heater core/evaporator tube seals from the module.
Remove the heater core cover screws (1).
Remove the heater core retaining screws (1).
Remove the heater core retaining straps.
Remove the heater core.
Remove the rubber seals from the inlet/outlet pipes of the heater core.

Installation Procedure

Install rubber seals to the outlet/inlet pipes of the heater core.
Install the heater core to the module.
Install the heater core retaining straps.



Install the heater core retaining screws (1).
Install the heater core cover.



Install the heater core cover screws (1).



Install the heater core/evaporator tube seal from the module.
Install the HVAC filter cover.
Install the HVAC module assembly. Refer to HVAC Module Assembly Replacement.

May 19, 2011 | Cadillac DeVille Cars & Trucks

2 Answers

How to replace heater core


Inspect/Replace If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Dec 11, 2010 | 1997 Chevrolet Lumina

2 Answers

Replace rear heater core


Inspect/Replace If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Dec 07, 2010 | 2003 Chevrolet TrailBlazer

2 Answers

Replace heater core


Inspect/Replace If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Dec 04, 2010 | 1995 Oldsmobile Cutlass Ciera

2 Answers

Heater core replacement


Inspect/Replace If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Dec 02, 2010 | 2003 Ford Crown Victoria

2 Answers

How to replace the heater core


Inspect/Replace If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Nov 28, 2010 | 1984 Ford F 250

2 Answers

Heater core replacement


Inspect/Replace If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Nov 27, 2010 | 1994 GMC Sierra

2 Answers

How do i replace heater core


Inspect/Replace If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Nov 26, 2010 | 1985 Cadillac DeVille

Not finding what you are looking for?
2005 Honda Pilot Logo

1,909 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...