Question about 2006 Pontiac Solstice

Open Question

06 pontiac soltice the IAT sensor has 5 wires whitch 2 wires lead to the sensor.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

fastboyz
  • 674 Answers

SOURCE: 2008 E-350 IAT sensor wires

is this what you recieved?9af2263.jpg

Posted on Nov 12, 2008

  • 408 Answers

SOURCE: code came back as iat sensor reading high

IAT stands for Air Intake Temperature Sensor and it is located in the intake tube coming from the air filter box tot he engine. Easiest way to find it is look at the top of your engine where it says 2200. Coming right out of that manifold is a black ribbed tube about the size of a baseball to softball. It should be going towards the direction on the front drivers side. on the back side of that tube, about 4 inches away from the intake manifold (the things that says 2200) is a plug with wires. That is your IAT Sensor. If it is unplugged, plug it back in. Otherwise unplug it and replace it. Make sure to disconnect the battery while you do this so the computer resets itself after the new one is installed. Thanks and please don't forget to rate!

Posted on Jul 15, 2009

  • 850 Answers

SOURCE: 1992 Pontiac Grand PrixPower loss,erratic idle

spark plug gaps are very critical on computerised cars!! [some wont even start!]
distributor module may be breeaking down as temp rises they fail!
otherwise do compression check as it may have valve problems
also check plug leads & injectors aswell as the fuel pump pressure [ could bestarving for fuel]

Posted on Jul 18, 2009

  • 4336 Answers

SOURCE: i have 2 pending codes for a 99' pontiac grand

Try unplugging and plugging the map sensor, this device should have manifold pressure hooked up to it, via hose, so check for cracks or leaks. Then clear codes and test again.

Posted on Sep 25, 2009

  • 18 Answers

SOURCE: wire colors for my IAT sensor

red with blue stripe and black... cut the red with blue strip and connect one end of the resistor to the harness side. Then splice the other end of the resistor to the black wire... do not cut it just splice into it.

Posted on Dec 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

What color is the positive wire on iat sensor on 06 pontaic g6 gt with a 3.5l motor


The iat is part of maf sensor. The iat gets 5 volts ref from the computer.
Hope I got the correct wiring diagram? I try to be accurate.
26328807-dfdklcxrhpcuw1hfcgvzf0s1-3-0.jpg

Oct 26, 2016 | Cars & Trucks

1 Answer

For a 2005 GMC yukon 5.3L what are the wire colors that control the IAT sensor There should only be 2 wires controlling it but there are 5 on the connection as it controls the MAF and IAT with the sa


The intake air temp sensor is part of the MAF sensor so yes there are 5 wires.
The two wires that go to the air temp sensor are tan and black. The other three are for the MAF.

Apr 20, 2013 | GMC Yukon Cars & Trucks

1 Answer

Need to know which two wires lead to my maf/iat sensor. my plug has five wires. 2004 porsche 911 c4


If it has 5 wires then 5 wires are used

1 grd
2 refV
2 Signal Return

You have 2 sensors in one module

Apr 03, 2011 | Porsche 911 Cars & Trucks

1 Answer

I have 5 wires going to mt IAT sensor. i need to know which 2 wires lead to the MAF/IAT SENSOR.its a 2004 chevy tahoe z71 4x4 with a 5.3 liter v-8. im putting a computer chip on so need the color of the...


Well im not sure why you are asking this question . They are two differant systems the mas air flow and the idle air intake bolth run off a 5 volt referance voltage but are not related so to speak to each other as far as the same ref voltage the same ground as every thing else .The IAT MAP TP ECT and fuel pressure sensor are one side and the MAF EGR and the EVAP are on the other side but all on a common ground . Ex plain what you are trying to do and why you are trying to do it and mabey i can make your life a little easyer and what caused this problem

Apr 02, 2011 | Chevrolet Tahoe Cars & Trucks

2 Answers

I am looking for my IAT or my CTS in my 06 expedition . do you know where it is ?


IAT inlet air temp sensor is part of the MAF sensor. It is the 2 outside wires of the MAF conector

Jan 31, 2009 | Ford Expedition EL Cars & Trucks

1 Answer

IAT location on my Scion XA


Your intake air temperature sensor is part of the MAF (mass airflow sensor) and located right off the air filter housing in the large tube going to the throttle body.Its held on with 2 screws and has a 5 wire electrical plug going to it.

Jan 16, 2009 | 2006 Scion xA

1 Answer

Exact location of iat sensor


Looking for the IAT on my G6. I know its in with the wires on my MAF sensor but of the 5 wires which two are the ones im looking for?

Jul 29, 2008 | 2006 Pontiac G6

Not finding what you are looking for?
2006 Pontiac Solstice Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...