Question about 2006 Ford F 350 Super Duty

1 Answer

I am trying to remove the front wheels to change the brakes on my 06 F350 but they will not budge. Any help is appreciated

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

I assume that youve taken off the lugnuts?(had to ask).when you have removed them all just stand back a little and kick one side of the tyre,the wheel sometimes sticks to the flange.be ready to catch the wheel when it breaks off.

Posted on Oct 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Contact between brake caliper and disc brake on Ford f350 possible ujoint problem or ball joints some up and down movement in hub when wheel is removed


Since you mentioned U-joint, I'll assume you're talking about a 4x4 F350 front wheel. I am not that familiar with the F350 4x4, but if the rotor is touching the brake components (and you have good pads), the problem is not the ball joints or the u-joint. It is most likely the wheel bearings.
And if it's touching the caliper or anchor bracket, the bearings are pretty bad.
Jack the wheel off the ground. Grab the top and bottom of the tire, and see if there is any "play" in and out to the truck. There should be virtually no play. If not convinced, check the other side for comparison.

Apr 12, 2015 | Ford F-350 Cars & Trucks

1 Answer

95 f350 hard brake pedal


did you get your brakes fixed? If so what was wrong?

Nov 05, 2011 | 1995 Ford F350

1 Answer

Have an 89 festiva changed 5 master cylinders and still cant bleed front driver and rear pass wheel and also changed distribution block 3 times. i cant bleed it rite from the front port of the master...


Section 06-06: Hydraulic Brake System 1992 Festiva Workshop Manual GENERAL SERVICE OPERATIONS Manual Bleeding
  1. Read Hydraulic System Bleeding General Information.
  1. Clean all dirt from the master cylinder filler cap.
  1. Fill the master cylinder with the specified brake fluid. During the bleeding operation do not allow the master cylinder to run dry.
  1. If the master cylinder is known or suspected to contain air it must be bled before the wheel cylinders or calipers. To bleed the master cylinder, loosen the front line fitting and have an assistant push the brake pedal slowly through its full travel. While the assistant holds the pedal, tighten the brake line fitting. After the line fitting is tightened, the assistant may release the brake pedal. Repeat this procedure on the rear brake line. Repeat the entire process several times to ensure all air has been removed from the master cylinder.
  1. Remove the bleeder screw cap from the appropriate rear wheel cylinder.
  1. Position a box end wrench on the bleeder fitting.
  1. Attach a rubber hose to the bleeder fitting. The hose has to fit snugly around the bleeder fitting.
  1. Submerge the free end of the hose in a container partially filled with brake fluid.
  1. Loosen the bleeder fitting approximately three quarters of a turn.
  1. Have an assistant push the brake pedal slowly through its full travel and hold it there.
  1. Close the bleeder fitting.
  1. Have the assistant release the brake pedal.
  1. Repeat Steps 9 through 12 until air bubbles cease to appear at the submerged end of the bleeder hose.
  1. When the fluid entering the bottle is completely free of bubbles, tighten the bleeder screw, remove the bleeder hose, and install the bleeder screw cap.
  1. Repeat Steps 5 through 14 at the appropriate diagonal front caliper.
  1. Check the master cylinder fluid level. If necessary fill it to the correct level with the specified brake fluid.
  1. Check pedal feel. If the pedal remains spongy, repeat the bleeding process or, if necessary, refer to Diagnosis and Testing in Section 06-00.

Jan 04, 2011 | 1991 Ford Festiva

1 Answer

Do you have to take the ball joints off to change the universal joint in the front axle on a 2002 ford f350


no you do not just remove brakes wheel rotor and wheel bearring hub . Then pry shaft out straight it my be a little hard but it will come out.

Oct 30, 2010 | 1994 Ford F150 Styleside Supercab

2 Answers

Cant remove wheel hub


here is procedure

Section 04-01: Suspension and Wheel Hubs, Front 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Wheel Hub Bolt Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Refer to Section 04-04 .
  1. Remove disc brake caliper (2B120), and front disc brake rotor (1125). Refer to Section 06-03 .
Brake Shoe and Lining Removal
  1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478). Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120), front disc brake rotor shield (2K004) or front wheel knuckle (3K185).
  1. Remove rear brake pin retainers (2N386). ( I think it is a T 40 torx bit you need)
  1. NOTE: It is not necessary to disconnect hydraulic connections.

    Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125). Do not pry directly against metal caliper piston or damage will occur.
  1. Position disc brake caliper out of the way and support with wire to avoid damaging the disc brake caliper and front brake hose (2078).
  1. Remove outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate.
  1. Remove inner brake shoe and lining assembly.
  1. Position lug bolt (1107) to clear front wheel knuckle (3K185).
  1. Remove lug bolt from wheel hub (1104).



7548d8f.gif

Installation
  1. Install lug bolt into wheel hub.
  1. Using a lug nut (1012), seat wheel hub bolt into wheel hub.
  1. Install front disc brake rotor and disc brake caliper. Refer to Section 06-03 .
  1. Install wheel and tire assembly. Tighten lug nut to 115-142Nm (85-104 lb-ft).

May 25, 2009 | 1996 Mercury Sable

1 Answer

How to replace front rotors


You'll need to take the wheel bearings off. the rotors are bolted to the hub and the bolts are located in the back of the hub thus having to remove the wheel bearings and removed the hub/rotor assy.

Apr 26, 2009 | Nissan Frontier Cars & Trucks

1 Answer

I am trying to get the wheel assembly apart to change the front bearings on a 1996 mercury villiger


http://groups.yahoo.com/group/villagerquest/

9ad2184.gif
Item Part Number Description 1 — Cotter Pin 2 — Nut Retainer 3 1131 Insulator 4 3B477 Front Axle Wheel Hub Retainer 5 1195 Front Wheel Outer Bearing Retainer Washer 6 1104 Wheel Hub 7 1107 Lug Bolt 8 3K050 Snap Ring 9 3123 Front Wheel Bearing 10 2K004 Front Disc Brake Rotor Shield 11 3130 Front Wheel Knuckle

Wheel Hub, Wheel Knuckle and Wheel Bearing SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Tie Rod End Separator T85M-3395-A
Removal
  1. Raise and support the vehicle.
  2. Remove the wheel (1007) and tire assembly.
  3. NOTE: It is not necessary to disconnect the front brake hose (2078).

    Remove the disc brake caliper (2B120) and suspend it with mechanic's wire out of the way. Refer to Section 06-03 for the removal procedure.
  4. Remove the front disc brake rotor (1125).
  5. Remove and discard the cotter pin.
  6. Remove the nut retainer and insulator.
  7. Remove the front axle wheel hub retainer (3B477) and the front wheel outer bearing retainer washer (1195).




  8. Remove and discard the cotter pin from the front suspension lower arm ball joint (3050).
  9. Loosen the front suspension lower arm ball joint nut until it contacts the front wheel driveshaft joint.


    stv~us~en~file=f8063b.gif~gen~ref.gif

  10. Strike the front wheel knuckle with a hammer while pulling down on the front suspension lower arm (3078) until the front suspension lower arm ball joint separates from the front wheel knuckle.




  11. Remove the front suspension lower arm ball joint nut.




  12. Remove the front suspension lower arm ball joint from the front wheel knuckle.
  13. Remove and discard the cotter pin.




  14. Remove the tie rod end nut.




  15. Use Tie Rod End Separator T85M-3395-A to separate the tie rod end (3A130) from the front wheel knuckle.




  16. Remove the front brake anti-lock sensor bolt.




  17. Remove the two front shock absorber-to-front wheel knuckle nuts.




  18. Remove the two front shock absorber-to-front wheel knuckle bolts.
  19. Remove the front shock absorber (18124) from the front wheel knuckle.
  20. Use 2-Jaw Puller D80L-1002-L, or equivalent, to separate the front wheel driveshaft and joint (3B436) from the front wheel knuckle.
  21. Remove the front wheel hub, front wheel knuckle and front wheel bearing as an assembly from the vehicle.
  22. If necessary, match mark and remove the steering stop bolt and steering stop bolt jam nut from the front wheel knuckle.




Installation
  1. Position the front wheel hub, front wheel knuckle and front wheel bearing as an assembly on the front wheel driveshaft and joint.
  1. Install the front wheel knuckle into the front shock absorber.
  1. Install the two front shock absorber-to-front wheel knuckle bolts.
  1. Install the two front shock absorber-to-front wheel knuckle nuts. Tighten the front shock absorber-to-front wheel knuckle nuts to 113-123 Nm (83-91 lb-ft).

Apr 10, 2009 | 1996 Mercury Villager

2 Answers

How do you change glow plugs in 06 f350 powerstroke? where is /are speed sensors on 06 f350 superduty powerstroke


remove the inner wheel wells or cut it back to get some access its tight that way though i would just remove the two of them its 10& 11 mm on the top sidde just let everthing hang , it is either 5.5 mm or a 7 mm . the speed sensor is in the transfer case for the 4x4 or on theh rear on the trans for 2wd

Feb 18, 2009 | 1995 Ford F350

1 Answer

2004 F350 Won't go into 4 wheel drive


HI! I have the same truck and to get it into four wheel drive shift to neutral first, apply the foot brake, move selector knob to fourwheel drive and then try to proceed. I hope this helps, John

Nov 24, 2008 | 2003 Ford F350 Super Duty DRW SuperCab

4 Answers

Ford f350 drum brake


Don't listen to the last guy. The drum does not just slide off. You have to remove the axle by removing the eight 5/8" bolts and pulling it out. Inside the hub you will find a ratcheting lock nut. Visible will be 4 slots where a special socket fits. You can buy the socket from a parts store or you can just use a 1/4" punch and slowly hammer to slowly thread the nut off. Drivers side is left hand thread while the passenger side is right hand thread. Remove the nut and the outer bearing will fall out (so catch it before it hits the dirt). Then slide the drum off. While you inside there it is a good idea to replace the axle seal. It's about $30 and an easy change.

Jul 07, 2008 | 1990 Ford F350

Not finding what you are looking for?
Cars & Trucks Logo

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...