Question about 2006 Dodge Stratus

Open Question

Driver's side power lock switch stopped working. locks work keylessly and the passenger side switch is still working.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Scorpedo
  • 111 Answers

SOURCE: Passenger window only works from drivers switch

If you have already replaced the passenger side switch and it still doesnt work its a good chance that there is a pinched wire in the door itself. However usually it wont work from the drivers side either. But I still suggest looking there first.

Posted on Dec 12, 2008

Ad
bestdarngood
  • 3037 Answers

SOURCE: power windows

As long as the windows will work fine some of the time, it sounds like the problem is in the power supply and replacing the fuse should fix it, otherwise there may be a loose wire somewhere in the circuitry.

Posted on Jun 03, 2008

  • 3 Answers

SOURCE: 2003 Dodge durango sport all four power windows not working

I know its not what anyone would want to here but sounds like a short. Best thing to do is first wiggle your key switch when the vehicle in in the on position then at the same time try to check to see if locks or windows are working. Then do the same in while the rig is running. If that dont work your ignition is fine and you need to take off door panels and check and wiggle all conections on window motors and lock motors and look for melted or burt wire or some that might have got hot. If all is good there you need to go to the back of the fuse box were the fuses to those items plug in and check there. As far as the service engine light goes either take it to the nearest Schucks or AutoZone and they will check it for free if not cycle the key on and off 3 times and on the 3rd time leave it in the on position look at your odometer light and it will flash a code remember that code and type Dodge then the code on yahoo search and it should tell you why your light is on Hintz whay sensor is bad. Hope this helps.

Posted on Apr 05, 2009

  • 2 Answers

SOURCE: 2002 Dodge Grand Caravan Driver Door Lock/Unlock Switch

sorry not sure the 12v prob will help this swtich works on 5v off 3v unlock 1v lock single wire lock/unlock logic signals
I found wiring diagrams at
http://www.dodge.com/bodybuilder/2004/docs/wd/rswd/tc.pdf
it is 2004 but use the wiring diagrams to test the wires
(most likely to fail where they flex)
because it is using logic gates disconnect the plug at each end of the wire you are testing or the damn thing will find a few diffrent ways to trick you.

Posted on Apr 21, 2009

MNfisherman
  • 11896 Answers

SOURCE: 2004 Dodge 2500 RAM Quad-cab.

The switch itself may be faulty. Have you tested it with an ohmmeter? Have you tested power to the passenger switch with a voltmeter?

Posted on Sep 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power Lock Unlock Rocker Switch


Hi E,with key OFF, try spraying a little ELECTRIC CONTACT CLEANER from CRC or Radio Shack into space between switch & panel on driver's side,cycle switch back & forth 10 or 12 times.driver's side switch 'overrides' others ,if cleaner dosen't work,replace it first. Good Luck

Oct 18, 2014 | Cars & Trucks

1 Answer

1999 GMC Sierra inside door locks no longer work!


the leakage inside the door lock maybe damage or deslocate try to check

Jun 17, 2013 | 1999 GMC Sierra

1 Answer

I have a 2000 ford mustang. Suddenly my keyless entry remote stopped working. I replaced the battery and turned the off and on 8 times and the locks cycled. after which i pushed the unlock but nothing...


The keyless entry system is controlled by the (GEM) - generic electronic module .
Keyless Entry The electronic door lock system has two main components:
  • generic electronic module (GEM)(14B204)
  • keyless entry remote transmitter (15K601)
  • NOTE: Battery power and ground must be remove before disconnecting the GEM connectors to avoid setting false codes.
    Power Locks Operation The power locks feature allows the customer to lock and unlock the doors via momentary switches located on the driver and passenger door. When the GEM detects a momentary press of the driver or passenger lock button, the GEM will supply power to the driver or passenger lock actuators for approximately 250 ms from relays internal to the GEM. When the GEM detects a momentary press of the driver or passenger unlock button, the GEM will supply power to the driver or passenger unlock actuators for approximately 250 ms from relays internal to the GEM.
    Remote Keyless Entry Door Locks Operation The remote entry feature allows the customer to unlock the driver door, unlock all doors, and lock all doors using a valid remote transmitter as long as the ignition switch is not in RUN or START. The driver door is unlocked whenever the GEM detects a valid remote transmitter unlock transmission. All the doors are unlocked when the GEM detects a second valid remote transmitter unlock transmission within three seconds of the first transmission. All the doors are locked when the GEM detects a valid remote transmitter lock transmission. If the GEM detects a second valid remote transmitter lock transmission within three seconds of the first transmission, the doors will lock again, the horn will sound for 20 ms and the parking lamps will flash for 200 ms to indicate the doors are locked. If the GEM detects the driver or passenger door is ajar during the second lock transmission, the doors are locked again and the horn is sounded twice. If the GEM detects a valid remote transmitter lock transmission within three seconds of detecting a valid remote transmitter unlock transmission, the GEM will lock all the doors
    • The doors do not lock/unlock using the remote transmitter
    • Ignition switch.
    • GEM.
    • Remote transmitter.
    • Remote transmitter batteries.
    • GO to Pinpoint Test C .
    You followed the program instructions to the letter ? Programming -Keyless Entry Remote Transmitter NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
    NOTE: All previous transmitter identification codes (TIC's) will be erased when programming mode is entered.
    NOTE: To program (or reprogram) the keyless entry remote transmitters into the generic electronic module (GEM)(14B204), perform the following steps.
    1. Turn the ignition from OFF to RUN eight times within 10 seconds, ending in RUN. If the GEM has successfully entered program mode, it will lock and unlock all the doors.
    1. NOTE: The first TIC must be entered within 7.5 seconds of entering the program mode and additional TICs must be entered within 7.5 seconds of the first TIC. The programming mode is exited whenever the timing constraints are not met.
      Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.
    1. If the door locks do not respond for any keyless entry remote transmitter, wait for several seconds and press the button again.
    1. Turn the ignition switch to the OFF position, or wait up to five minutes after step 1, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the GEM will lock and unlock all the doors one last time.
    1. Take an have the vehicle checked for DTC'S
B1396 Power Door Lock Circuit Short to Battery GEM GO to Pinpoint Test B . B1397 Power Door Unlock Circuit Short to Battery GEM

Apr 12, 2017 | Ford Mustang Cars & Trucks

1 Answer

1998 Jeep Grand Cherokee Laredo TSI, Passenger side windows do not work from master switch on drivers door. Both driver side windows work from master switch on drivers side. Passenger side windows do work...


It has to be the switch or the wiring, right? So pull out the switch and probe the back with a volt meter to see if power is coming out of the switch. If yes, trace the wires to the doors.
0900c152800aa140-zzyiglue2iivran2oy1paayi-3-0.gif

Jun 30, 2017 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Power locks don't work with remote or control from


The door lock/unlock input from the driver's key switch goes to the Door Multiplex control unit (main switch), the Door multiplex control unit then sends a signal on the BUS (CAN) circuit to the passenger's multiplex control unit; the passenger's multiplex control unit then controls all the door locks. The passenger's door lock key switch inputs to the passenger's multiplex control unit, if the locks work from the passenger's side key switch but not the driver's side key switch, the most likely cause is the driver's multiplex control unit (main switch) not sending the signal to the passenger's side multiplex control unit. This could also be the drivers side door lock actuator. Hope this helps!

Jan 07, 2010 | 2003 Honda Pilot

1 Answer

Power door locks do not work with keyless remote control


There are two multiplex control units - one on the driver side and one onthe passenger side - which one did you unplug? The one on the driver side is the main "Brain" while the other one is the one that houses the keyless reciever. According to the service manual, any troubleshooting of this system must begin with the one on the driver side. It can get quite involved because Honda does not provide actual troubleshooting (symptom) charts, just descriptions of the electrical connectors and what conditions should be present at each conector pin under what system condition. (each pin has to be tested to determine what is malfunctioning) The system is not capable of outputting fault codes of any kind.

Nov 08, 2009 | Honda Accord Cars & Trucks

1 Answer

Heated seat AND driver's side door lock doesn't work


no connection of the two, start by checking switch for heated seat, if power is there and switch is good then heating element is probaly bad,the lock could be linkage jam or lock acuator, good luck.

Oct 27, 2009 | Ford Explorer Sport Trac Cars & Trucks

1 Answer

2003 Civic left Side Electric Door lock Broken


bye a diff car hondas are nothing but problems

Feb 10, 2009 | 2003 Honda Civic

2 Answers

Keyless entry and door locks


Do you have he owners manual? instructions are in there for the keyless entry system. If not go to this link:

http://www.motorcraftservice.com/pubs/content/~WOTEXP/~MUS~LEN/41/96expog1e.pdf

Sep 21, 2008 | 1996 Ford Explorer

Not finding what you are looking for?
2006 Dodge Stratus Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...