Question about 2005 Hyundai Elantra

2 Answers

How do i change fuses for power windows - 2005 Hyundai Elantra

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 6,826 Answers

Get a fuse kit that has fuses and a puller and tester from Walmart or local parts store.
Locate the fuse which is either under the hood or under the dashboard on the driver's side.
There may be a sticker on the door that tells you which fuse is for PW or Power Windows.

According to autozone.com:

Inspect/Test/Replace
To remove a fuse:

  • With glass cartridge or blade-type fuses, a special fuse removing tool can be used to remove a bad fuse.
  • Blade-type fuses are easy to remove by hand or with a needle nose pliers.
To replace a fuse:
  • Be sure to replace a fuse with the correct one for the application.
  • SFE (Society of Fuse Engineers) and all-glass cartridge (sometimes called "Bussman" or "Buss") fuses will interchange with one another, so care is required.
  • Be sure that the fuse is the correct rating. Too low an amp rating will result in burned fuses. Too high a rating can cause a fire.
  • Check the end of the fuse for its amp rating. The correct amp rating of the fuse to be used is listed on the fuse block.
  • Fuses are generally numbered, and the main components abbreviated.
how do i change fuses for power windows - f14-36.jpg Typical fuse box or panel.
  • On late-model cars, there may be icons or symbols indicating which circuits they serve. This identification system is covered in more detail in the owner's and service manuals.
NOTE
To calculate the correct fuse rating, use Watt's law: watts ÷ volts = amperes. For example, if you are installing a pair of 55-watt fog lights, divide 55 by the battery voltage (12 volts) to find out how much current the circuit has to carry. Since 55 ÷ 12 = 4.58, the current is approximately 5 amperes. To allow for current surges, the correct in-line fuse should be rated slightly higher than the normal current flow. In this case, an 8- or 10-ampere fuse would do the job. NOTE
It's advisable to carry an assortment of spare fuses in the glove compartment. It is difficult to know when one will blow. Also, you should learn borrow a fuse from a less critical circuit. For example, it is possible to do without power for the radio or air conditioner, if a fuse is needed for the headlights or brake lights. Make certain, however, that the fuse borrowed and later replaced has the same current rating. Remember that a blown fuse was caused by something going wrong. Replacing the fuse may or may not give a temporary solution to the problem.

Posted on Oct 16, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

    Sergeant:

    An expert that has over 500 points.

  • Master
  • 381 Answers

Locate the fuse box and in there you will have a diagram of which fuse is for the windows take it out and replace with new one

Posted on Oct 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No power to instrument cluster and power windows


! Check the black fuse box under the hood near the battery ! Check it out on you tube !

May 15, 2014 | 1997 Jeep Grand Cherokee

1 Answer

Power window fuse


On most models the power window circuit is on a 30amp fuseable link, not a regular fuse. Are you sure you replaced a fuse ?

Jun 17, 2013 | 1998 Lincoln Navigator

1 Answer

Driver window won't work


first thing first check ur fuse for the power window. look at ur car manual to locate the switch box. if the fuse is good check the window motor by removing the door panal then locating it inside the door. use a power tester to see if power is getting to the motor by connecting it to the positive (red) wire connected to the window motor. if its not getting power the change the motor. if it is then you may have a window switch problem. if you have change the motor, switch, and fuse the you make have a wire shortage proble so take it to a payed professional for further advice or service. good luck

Jan 18, 2013 | 2005 Honda Pilot

1 Answer

I got a rav4 2007 and its blown the fuse of the power windows i replace it 4 times and the fuse i change is of the same type 30 AMP did i have to change with other of more AMP?


The 30A PWR fuse connects power directly to the driver's side power window switch a short in the switch or any of the power window regulator motor circuits could cause the PWR fuse to keep blowing

Nov 08, 2012 | 2007 Toyota RAV4

1 Answer

06 DODGE STRATUS WINDOWS INOP, NO POWER TO FUSE OR CIRCUIT BREAKER


If no power to the fuse panel for that fuse and circuit breaker, you may have a maxi-fuse burnt out in the power distribution box by or near the battery. Check all your fuses under the hood.

Apr 05, 2012 | 2006 Dodge Stratus

2 Answers

Automatic door locks stopped working. Power window controls do not work. The only window working is drivers window.


Change the battery in your wireless remote control. Check the fuses located underneath the drivers side steering wheel, flip the fuse box cover lid over and replace the power window and power door lock fuses. The back of the cover lid will have a diagram showing where each fuse is located, replace with the same number amp fuse. If your fuses are good and the battery inside your remote is new then you will need to replace the drivers side power window switch, click on the link below to view a replacement:

http://cgi.ebay.com/ebaymotors/05-06-Toyota-Tundra-OEM-Master-Power-Window-Switch-LKQ-_W0QQcmdZViewItemQQfitsZYearQ3a2006Q7cMakeQ3aToyotaQ7cModelQ3aTundraQQhashZitem20b3f6b69aQQitemZ140458243738QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories

Oct 18, 2010 | 2006 Toyota Tundra

1 Answer

Power windows wont roll down


It could be the fuse to the power windows. Check the fuse box . it is on either side of the dash just inside the door. or near the glove box. Look for any burnt fuses and replace them with the same amp fuse. The same color.There is a fuse remover in the fuse box. You use that to remove the fuses by grabbing the fuse with the edge of the tool. And pulling the fuse out.

Feb 06, 2009 | 1995 Buick Regal

1 Answer

Power windows and mirrors


yes its a fuse. on the inside of the top of the fuse cover there is a listing. find the accessories or power opt. fuse and change it out.

Oct 01, 2008 | 2002 Dodge Neon

1 Answer

Power windows stuck (2002 Taurus)


You can open the hood and find the fuse unit of the car please change the fuse then try .

May 27, 2008 | 2002 Ford Taurus

Not finding what you are looking for?
2005 Hyundai Elantra Logo

540 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...