Question about 2004 Toyota Corolla

2 Answers

Power loss in 2004 Corolla Verso D-4D T2 at speed

After a cold start and about 10 minutes driving at speed 50-70 mph, the car will not accelerate and seems to hit a flat spot or limiter. Pressing the accelerator to the floor just kicks out smoke. Changing down then allows you to keep up a certain amount of torque and sometimes clears the problem. I have had the car on a diagnostic unit at a local garrage which shows no problems. I have checked for fuel leaks, have changed the fuel filter and run though some decent injector cleaner fluid in a full tank diesel. This fault tends to shows itself after 10 minutes (only at speed) and does not occur again until a start from cold. The car had no problems starting, running and has plenty of pull normally. I am very puzzled. Please help.

Posted by on

  • Anonymous Mar 14, 2009

    I have the exact same car and problem. Please let me know if you found a solution. Mine has a loss of power in the first 5 minutes from cold start and when I slow down for a junction it loses power. I've stopped turned it off them on again and it's been fine until the next cold start. The garage have done a diagnostic check and the mechanic seems to think that it's a problem with the primary fuel tank but has told me to go to the dealer to get another diagnostic check to make sure.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

You might want to check the MAF sensor(Mass Air Flow) and clean it with MAF/MAP cleaner. I am also kind of puzzled with this problem as I have a 2004 Corolla also, I only had power loss when my MAF went bad.

Posted on Jul 20, 2009

Change your air filter

Posted on Jul 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is mybcm not letting me pass insp there is no code on thi1996 chry lhs what is going on


You mean PCM most states read the readiness monitors depending on the state on how many they allow not to be completed. The first one on the list that is hard to get run and pass is the EVAP Because this requires the car to be cold and fuel tank must between 15%-85% and both air temp and coolant temp with in 10 degrees of each other. Start car let idle for 5 -10 minutes Then drive car normally no hard accelerations or quick stops bring speed to 50-60 mph and coast down to 20-15 mph without brake pedal input repeat this twice.Then bring speed to 58-62 mph and set cruise control run for 12-16 miles exit freeway caught a red light or stop and idle 2 minutes shut car off rest for 5 minutes and repeat freeway drive. then redo morning cold start again . then have some one test the generic readiness monitors to what needs to run and attempt again. California before 2000 1 can be incomplete after 2000 all have to be completed which is hard some will not run for 800 miles.

Nov 08, 2013 | 2001 Ford Escape

3 Answers

The car will run fine for about 10 minutes then it will stop accelerating???


ENGINE HESITATES WHILE ACCELERATION

LOSS OF ACCELERATION


It can be fuel pressure issue or it's the problem with accelerator pedal or its clogged filters causing there.

There are many other possibilities. I suggest you to go through the list of help links mentioned below, these will help you to confirm where the actual fault lies: -------

Jerks and Hesitates During Acceleration?

http://technoanswers.blogspot.in/2012/07/2004-dodge-town-country-jerks-and.html

-----------

Loss of acceleration?

http://technoanswers.blogspot.in/2012/02/loss-of-acceleration.html

---------

Headlights flickering and car hesitates to start?

http://howtobyme.blogspot.in/2012/02/headlights-flickering-and-car-hesitates.html

--------

How exactly the Vehicles Accelerator Cable works?

http://repairhelpcenter.blogspot.com/2011/11/how-exactly-vehicles-accelerator-cable.html

-------------

How exactly Vehicles Accelerator Pump Diaphragm Works?

http://repairhelpcenter.blogspot.com/2011/11/how-exactly-vehicles-accelerator-pump.html

--------

2000 Toyota Avalon: Engine Lean Codes and Knock Sound on Acceleration?

http://whatisbyme.blogspot.in/2012/05/2000-toyota-avalon-engine-lean-codes.html

---------

2004 Toyota Avensis: Acceleration And Deceleration makes noise on Front End?

http://whatisbyme.blogspot.in/2012/05/2004-toyota-avensis-acceleration-and.html

---------

Wheel hop under hard acceleration?

http://technoanswers.blogspot.in/2012/04/wheel-hop-under-hard-acceleration.html

--------

2009 Chevy impala accelerator pedal sensor?

http://technoanswers.blogspot.in/2012/02/2009-chevy-impala-accelerator-pedal.html

---------

Nissan Pathfinder stalls and bucks on Acceleration?

http://technoanswers.blogspot.in/2012/02/nissan-pathfinder-stalls-and-bucks-on.html

--------

Acceleration lag problem?

http://repairhelpcenter.blogspot.com/2012/01/acceleration-lag-problem.html

-------------

These details will help.

Thanks.

Nov 28, 2012 | 1999 Mercury Cougar

1 Answer

Drive cycle


Here is the OBD2 emission system drive cycle test procedure.
Engine coolant temp must be below 70c (158f) before starting the engine for either the first or second trip
The fuel level should be less than 1/2 full
First trip:
Start engine, idle for at least 1.5 minutes
Drive 3 minutes, hold b/f schdl: 1.5-2.0 msec, selector lever "3rd" eng rpm 1,800-2,000 A/C switch:ON Hold the recommended b/f schdl range. Allow road speed to vary as necessary.
Drive at 55-65 mph for 1.5 min b/f schdl 2.0-3.2 msec, selector lever "5th" Engine rpm 2,200-3,000
IGN "off" for at least 10 seconds (not more than 5 min)
Dive at 50-60 mph for 3 minutes Selector lever "4th" keep engine speed above 3,000 rpm Allow speed to vary if necessary. Do not decelerate for more than 3 consecutive seconds. A/C switch ON.
Drive at a steady state cruise of 53-58mhp b/f schdl more than 1.8 msec selector lever "5th" eng rpm 2,400-2,600
Downshift to "4th" and decel more than 5 seconds without breaking, then idle for 1 minute.
Drive two minutes b/f schdl less than 2.0 msec Accelerate to 41 mph, decelerate to 34 mph, accelerate to 41mph. Do not completely release the accelerator. A/C switch off.
Idle 1 minute in park or neutral
Drive two minutes Steady state cruise at 31-44 mph. Selector lever "4th" A/C switch OFF. Hold the accelerator pedal as steady as possible. Allow speed to change if necessary.
End of first trip. Turn the key off the begin the second trip.
Second trip:
Start engine, idle for at least 1.5 minutes
Drive 3 minutes, hold b/f schdl: 1.5-2.0 msec, selector lever "3rd" eng rpm 1,800-2,000 A/C switch:ON Hold the recommended b/f schdl range. Allow road speed to vary as necessary.
Drive at 55-65 mph for 1.5 min b/f schdl 2.0-3.2 msec, selector lever "5th" Engine rpm 2,200-3,000
IGN "off" add four gallons of fuel
Dive at 50-60 mph for 3 minutes Selector lever "4th" keep engine speed above 3,000 rpm Allow speed to vary if necessary. Do not decelerate for more than 3 consecutive seconds. A/C switch ON.
Drive at a steady state cruise of 53-58mhp b/f schdl more than 1.8 msec selector lever "5th" eng rpm 2,400-2,600
Downshift to "4th" and decel more than 5 seconds without breaking, then idle for 1 minute.
Drive two minutes b/f schdl less than 2.0 msec Accelerate to 41 mph, decelerate to 34 mph, accelerate to 41mph. Do not completely release the accelerator. A/C switch off.
Idle 1 minute in park or neutral
Drive two minutes Steady state cruise at 31-44 mph. Selector lever "4th" A/C switch OFF. Hold the accelerator pedal as steady as possible. Allow speed to change if necessary. I especially like the part where they want you to add four gallons of fuel. Not three gallons, not five gallons, four gallons. Gotta love those Nissan engineers. ...and of course they state that if the trace is not followed exactly (i.e. you botch the acceleration/deceleration) you have to start all over again from scratch

Feb 09, 2012 | 1996 Nissan Pickup

1 Answer

I am expriencing the same problem on 2004 Grand Prix. Did you vere find a solution?


Since you have "check engine" light turn on, will need scanner the PCM to know what fault code is stored there; with this code number could send you additional details, Sound like a emissions problem.

Keep in touch.

Feb 06, 2012 | 2004 Pontiac Grand Prix

1 Answer

What is the drive cycle for a 2004 Caravan after a sensor has been replaced?


Hello! The Drive-Cycle is as follows...Check engine light off, codes cleared; cold start...Warm up engine 5 minutes...Drive (w/ steady throttle) at a steady speed between 40 and 60 mph for 8 min...Stop and idle 3 min...Drive (w/ steady throttle) at a speed above 20 mph for 2 minutes...Turn key off, leave off 10 min...

Guru.............Saailer

Feb 07, 2011 | 2004 Dodge Caravan

1 Answer

NEED DRIVE CYCLE FOR 2004 CRV TO RESET CAT AND O2 MONOTOR


Here is the info

NOTE: The ignition key must not be on prior to the cold start otherwise the heated oxygen sensor diagnostic may not run.

1. As soon as the engine starts, idle the engine in drive for two and a half minutes with the A/C and rear defrost on. OBDII checks oxygen sensor heater circuits, air pump and EVAP purge.

2. Turn the A/C and rear defrost off, and accelerate to 55 mph at half throttle. OBDII checks for ignition misfire, fuel trim and canister purge.

3. Hold at a steady state speed of 55 mph for three minutes.

OBDII monitors EGR, air pump, O2 sensors and canister purge.

4. Decelerate (coast down) to 20 mph without braking or depressing the clutch. OBDII checks EGR and purge functions.

5. Accelerate back to 55 to 60 mph at half throttle. OBDII checks misfire, fuel trim and purge again.

6. Hold at a steady speed of 55 to 60 mph for five minutes.

OBDII monitors catalytic converter efficiency, misfire, EGR, fuel trim, oxygen sensors and purge functions.

7. Decelerate (coast down) to a stop without braking. OBDII makes a final check of EGR and canister purge.

Oct 02, 2010 | 2004 Honda CR-V

1 Answer

Obd2 system rediness status won't clear so I can run the smog test due to replacing the battery.


takes a long time to run the rediness test since there are 6 different tests to complete...

PROCEDURE 1
EVAPORATIVE EMISSION SYSTEM LEAK MONITOR
Inspection Conditions
Engine coolant temperature: 30°C (75°F) or less (The engine is stopped before the test drive is started).
Atmospheric temperature: 5 - 30°C (41 - 113°F).
Condition of A/T: Selector lever D range.
Fuel remained in fuel tank: 30 - 50% is recommended.
Time required: 16 minutes or less after started the engine.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position. Well be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 16 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position.

PROCEDURE 2
FUEL TRIM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: -10 - 60°C (14 - 140°F).
Condition of A/T: Selector lever D range.
Time required: 30 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 30 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 3
CATALYTIC CONVERTER MONITOR
Drive Cycle Pattern
Inspection Conditions
Atmospheric temperature: -10°C (14°F) or more.
Condition of A/T: Selector lever D range.
Engine coolant temperature: Not set.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
Travel for 300 seconds or more while keeping the vehicle speed at 89 km/h (55 mph) or more.
Decelerate until the vehicle speed is within 80 km/h (50 mph) or less.
While traveling at 56 - 80 km/h (35 - 50 mph) for 10 minutes or more, fully close the throttle at least once in 2 minutes and decelerate for 10 seconds or more.
Do not repeat deceleration too often.
Vehicle speed may go below 56 km/h (35 mph) after the deceleration.
Stopping and braking are permitted. (If stopped or drive at 56 km/h (35 mph) or less for more than 5 minutes the monitoring may be stopped. In this case please restart monitoring from the beginning.)
After completing the above deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 5 times.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 4
HEATED OXYGEN SENSOR MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or more.
Atmospheric temperature: -10°C - 60°C (14 - 140°F) or more.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 - 80 km/h (35 - 50 mph) and travel for 16 minutes or more.
Stopping and braking during this operation are permitted. Keep the accelerator opening degree constant for 1 minute or more after each acceleration.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 5
EXHAUST GAS RECIRCULATION (EGR) SYSTEM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: 5 - 60°C (41 - 140°F).
A/C switch: OFF.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While traveling 16 minutes or more at 56 - 80 km/h (35 - 50 mph) with engine speed 2,000 r/min or above, fully close the throttle at decelerate for 5 seconds or more until the engine speed reaches 1,000 r/min or under.
Do not repeat deceleration too often.
Stopping and braking are permitted (Rapid deceleration and sharp steering are not permitted).
After completing the deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 8 times by fully closing the throttle valve.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 6
OTHER MONITOR (Main Components, Sensors & Switches, Wire Breakage & Short Circuit)
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature:
100°C (212°F) or less (Except engine coolant temperature sensor monitoring).
30°C (86°F) or less (Engine coolant temperature sensor monitoring).
Atmospheric temperature:
5°C (41°F) or more (Except engine coolant temperature sensor monitoring).
-10°C (14°F) or less (Engine coolant temperature sensor monitoring).
Condition of A/T: Selector lever D range.
Time required: 21 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start
Accelerate until the vehicle speed is 56 km/h (35 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 km/h (35 mph) or more and travel for 16 minutes or more.
Return the vehicle to the shop.
After stopping the vehicle, continue idling for 5 minutes, and then turn the ignition switch to the "LOCK" (OFF) position. Moreover, the vehicle should be set to the following conditions for idling.
A/C switch: OFF
Lights and all accessories: OFF
Transmission: Neutral

Sep 15, 2010 | 1998 Mitsubishi Eclipse

2 Answers

Not Ready for Smog test


it is not how many miles but the type of driving.

here is a OBD2 drive cycle test.

Generic OBD II "Drive Cycle" Most OBD II ("On-Board Diagnostics II") diagnostic monitors will run at some time during normal operation of the vehicle.
However, to satisy all of the different Trip enable criteria and run all of the OBD II diagnostic monitors, the vehicle must be driven under a variety of conditions. The following drive cycle will (theoretically) allow all monitors to run on (??) vehicle. (Note: Drive cycle specifics vary by vehicle!)
  1. Ensure that the fuel tank is between 1/4 and 3/4 full.
  2. Start cold (below 86°F /30°C) and warm up until engine coolant temperature is at least 160° F (typically requires at least one minute; up to 3 minutes).
  3. Accelerate to 40-55 MPH at 25% throttle and maintain speed for five minutes.
  4. Decelerate without using the brake (coast down) to 20 MPH or less, then stop the vehicle. Allow the engine to idle for 10 seconds, turn the key off, and wait one minute.
  5. Restart and accelerate to 40-55 MPH at 25% throttle and maintain speed for two minutes.
  6. Decelerate with using the brake [or the clutch!] by coasting down to 20 MPH or less, then stop the vehicle. Allow the engine to idle for 10 seconds, turn the key off, and wait one minute.

Jun 04, 2010 | 2001 Kia Sephia

1 Answer

Toyota corolla verso d-4d loss ofpower


Just change the air flow meter.Thats faulty.

Jul 24, 2009 | 2005 Toyota Corolla

Not finding what you are looking for?
2004 Toyota Corolla Logo

845 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...