Question about Mazda 323

Open Question

Mazda 323 03 The handbrake,tcs ,and abs lights come on after 4 miles or 11 miles go off when i turn engine off. Somtimes are straight back on somtimes not .Has been tested on Mazda machine still not 100% sure its the sensors ,Quoted 500 to fix it ? Help

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: Check engine light + TCS = braking vibrations

You need to get to a repair shop and have them read the diagnostic codes (the computer port is in the center console under the change holder/lighter). With that amount of mileage, it is very likely the code will show that the oxygen sensors and/or catalytic converters need replacement. If that is the case you will also need a tuneup (plug, wires, etc). I had this done a year ago at 160,000 miles. It is a pricey repair but I get 29mpg at highway speeds and it runs nicely on regular (less power but no pinging).

Posted on Nov 10, 2008

Ad
  • 1 Answer

SOURCE: ABS, Traction control and handbrake

I have a Mazda Capella (626) 1998 and had similar problem other than it was running on 4 cylinders and the hand brake light was not on but speedometer was not functioning and the ABS light was on. The rear ABS senssor was the problem.
SDM

Posted on Jan 23, 2009

  • 909 Answers

SOURCE: 1998 escort 1.8 zetec hesitates when warm somtimes

could be any of the following
1, worn ,faulty or incorrectly gapped spark plugs
2, engine management fault
3, vacuum leak at the inlet manifold or associated hoses

Posted on May 03, 2009

  • 1 Answer

SOURCE: traction control light comes on while driving in good weather

My 2002 Millenia just started doing this the other day, while on the freeway when it started doing it i would shut engine off and restart it and it would be good for a while then it would do it again, i am still looking for solution, has any one found one?

Posted on Jul 11, 2009

  • 148 Answers

SOURCE: 2003 Hyundai Santa Fe ABS light is on along with TCS light

you may have damaged the ABS sensor or wire to the sensor up front check the wire that runs from the inner finder well and make sure it connected to the ABS sensor on the spindle

Posted on Jul 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

ABS light come on when i am towing


the tcs system is detecting the weight and sway of the trailer because the load on the hitch is too much- that's the simple answer.

The ABS and TCS work together - the ABS system is what detects wheel spin and tell the TCS which diverts and/or control power.

Oct 08, 2014 | 2008 Mazda MAZDA6

1 Answer

CHECK ENGINE LIGHT, TCS OFF LIGHT AND THE TRACTION LIGHT are on...


Code 340 is for a problem with the cam position sensor. That would affect the tach and cause the check engine light to be on.
And most all the time the check engine light is on the other warning lights will be also. The Traction control system uses the engine and the ABS system to function. So if there is a problem with the engine, the TCS will be disabled.
The cam sensor and circuits would need to be tested. It could be a wiring problem.

Apr 24, 2013 | 2006 Mazda 6 s

1 Answer

How to reset renault laguna ABS, Service and Handbrake malfunction lights


Whenever this warning light or any other stays on in the dash it is indicating that the systems control module (or the system sensor in the case of lights like low oil pressure, door open indicators etc.) has detected a fault, it then disables the system (this applies to ABS,TCS, TCM, SRS and BCM faults and others) as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)

Legend of Abbreviations. ABS Antilock brake system.TCS Traction control system, TCM Transmission control module, SRS Supplemental restraint system, BCM Body control module

Oct 23, 2012 | Cars & Trucks

1 Answer

Hello! I have a 1996 Mazda Millenia with 133,000miles on it. Just recently the ABS Light and the TCS OFF light has been coming on and off randomly(no blinking, just illuminated). I've done a bit of...


When both of these lights are on, I always suspect the wheel speed sensors.

Please see my tip at http://www.fixya.com/cars/r6003525-abs_traction_control_lights . These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me with model, year and engine info.

Sep 28, 2010 | Mazda Millenia Cars & Trucks

1 Answer

How do you reset the ABS and TCS lights on a 2002 Mazda 626?


these reset each time the key is turned on to start the car, if they remain on there is a problem in the system, the ABS and TCS are run by the same system control module, have it tested to see what fault code shows up to indicate what part has failed.

Aug 23, 2010 | 2002 Mazda 626

2 Answers

Mazda 626 2000 - warning lights for ABS, TCS


what u do to stop the vehicle and remove the battery head and refix,if the problem still persits go for thorough scanning.

Mar 25, 2010 | 2002 Mazda 626

1 Answer

Tcs light come on along with abs an hand break light


You most likely knocked the electric plug loose when you changed the brakes, go back and make sure they are tight.

Jul 24, 2009 | 1999 Mazda 626

1 Answer

Traction control light comes on while driving in good weather


My 2002 Millenia just started doing this the other day, while on the freeway when it started doing it i would shut engine off and restart it and it would be good for a while then it would do it again, i am still looking for solution, has any one found one?

Apr 23, 2009 | 2000 Mazda Millenia

2 Answers

ABS, Traction control and handbrake light is on. Car was running on 3 cylinders previous to the lights coming on. 1999 Mazda SP20 Familia (323)


I have a Mazda Capella (626) 1998 and had similar problem other than it was running on 4 cylinders and the hand brake light was not on and the ANSWER was a speed sensor which is to do with ABS system needed replacing. You can determine which one is broken by putting volt meter over each of them.

Nov 17, 2008 | Mazda 323 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

278 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8725 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...