Question about 1999 Dodge Ram 2500 4WD

1 Answer

I have a vibration that starts about 1700 rpms at 60-65 mph (give or take). I have had tires balanced, checked u joints drive shaft, front hub bearing replaced, new shocks all around, driver side new ballstuds and tie-rod end. any advice appreciated greatly.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

Let your wife drive or slow down. Seriously, sounds like you have covered just about everything. Try increasing or decreasing your tire pressures a little just to see if it has any effect.

Posted on Oct 16, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changed both front bearings,both u-joints,still getting vibration when speed reaches 50+mph.Tires are tight and balanced


didnt specify vehicle --generic answer --recheck balance,was alignment done after pars replaced is this an all wheel drive ,front wheel drive ,4wheel drive or rear drive vehicle --check c/v axles ,transfer axle /shafts -bent rims bad tire belt

Oct 25, 2016 | Cars & Trucks

3 Answers

Shakes at 65mph had tires balanced also I cant feel it in the steering wheel it feels like it's coming from the back passanger side or middle


put tires from rear up front and front to rear and see if tires cause a shake also make sure no debris on hub so rim sits flush if no change and still vibration check drive shaft and u joints

Jul 27, 2016 | 2003 Chevrolet Tahoe

1 Answer

I had a nail in front passenger tire. Took it off and got it plugged. I noticed a lot of grease around area.


Could be universal joints if rear wheel drive , you can physically see by checking the drive shaft at each end. If its that bad it will fall. Also could be tires out of balance

Mar 08, 2015 | Cars & Trucks

2 Answers

What would make the front end shake between 20 and 30 MPH and then go away?


Sounds like your transmission unit could do with a fluid change, along with a new filter. If you are over 100k in mileage, transmission shudder can be common in some models. Have an auto shop drive it and give you a firm quotation for fluid and filter replacement.

On the long shot, it could be a drive shaft joint tightening up if you have a transaxle.

Hope this helps...

Aug 26, 2014 | Cars & Trucks

2 Answers

2006 nissan path finder has a vibration after 40mph


check for failing "U" joints, loose /binding slip joint check for bent drive shaft check for missing balance weight off shaft.

May 04, 2014 | 2006 Nissan Pathfinder

2 Answers

My 1989 Chevey Celebrity started shaking the other day the front part of the car, not like the front end is messed up but it shakes.


Could be a wheel, tire, or axle shaft.
You could rotate the tires front to back and see if the vibration moves.
If it does the problem is one of the tires or wheels.
If it stays in the front, its probably one of the axle shafts. It could also be a hub bearing or something loose in the suspension. But a loose suspension part would normally show up when you hit a bump rather than on a smooth road.

Dec 25, 2012 | 1989 Chevrolet Celebrity

1 Answer

2005 mercury mariner vibrates a lot when driving up to 20 mph, then it's all smooth. I installed 4 new tires, did front end alignment and rear, did tire rotation and balance, now it is showing ABS


The vibration at low speeds can be due to possible fault in wheel bearings, drive shaft or even with a faulty steering system.You need to hoist up the car and check on all the individual wheels, hubs and also check for the ABS line to the wheel hubs which could have failed or there is a sensor failure on the wheel hub.

Mar 14, 2012 | 2007 Mercury Mariner Premier 4WD

3 Answers

Vibration only between 22 mph and 30 mph on my s10 (1999)


The vibration that is experienced must be confirmed if you can take a good test drive, asking a friend to drive in an empty road while you check on the front and back wheels for wobbling or noise.
If so the fault can be a worn out tyre, faulty wheel bearings or a hub.
Also the noise can be relative of the universal joints or the drive axle or propeller shaft going eccentric.
If you take an inspection under the car the loose universal joints or play on the propeller shaft can be confirmed. Also a fault in suspension/steering section cannot be ruled out.

Oct 11, 2011 | 1999 Chevrolet S-10 Pickup

1 Answer

2000 ford exploorer v-8 awd eddie bauer edition new wheels and tires new ball joints new tierods new shocks 3 front front end alignments started having a vibration in the front end at about 70+ mph had the...


Hello, I see you may a lot of changes and replaced a lot of parts. We leased an Explorer the same Year as yours. In our case there was a slight noise as well as vibration. The problem was the Front Hub bearings, They were bad at 18000 miles.

There are a few things I want to suggest. The spinning of the wheels on the lift will not load the bearings. A Dyno table can get everything turning with a load on it. As your vehicle is a 4x4, most Dyno's were 2 wheelers. You would have to call to find one for a 4x4.

Next, if the new Hubs do not help, have a look at the rotors. They are also balanced. You can spin balance the Wheel and rotor as a unit with a floor motor. It's not the best way to Balance because tire rotation or even shifting the Wheel on the lugs will UNbalance it. But this method CAN pinpoint a problem if a Balanced tire does not spin true when bolted to the vehicle. You will know the Rotor is off-balance and which axle is causing the problem.

Would be interested to see a Post of what you found.

Jul 09, 2010 | 2000 Ford Explorer

1 Answer

Vibration at 75 mph


Must be bad u-joint. To check it, let off the gas pedal. If it stops right away, it's the u-joint. If it takes a few seconds, it's a tire out of balance, or a bent wheel.

May 21, 2009 | 1992 Dodge Dakota

Not finding what you are looking for?
Cars & Trucks Logo

286 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...