Question about Mitsubishi Lancer

Open Question

Ecu gearbox auto 4G92 mivec.. what calour wire for ecu gearbox auto mivec??

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Nzero
  • 78 Answers

SOURCE: LEGACY 2.5 AUTO GEARBOX REPLACEMENT

hi there, needs to be the same number. computers need to match. tourque converters are different from 2.0/2.2 to the 2.5 engines. also shift points are different between models so needs to talk to the dash perfectly. hope this helps.

Posted on Sep 01, 2008

short shadey
  • 421 Answers

SOURCE: automatic tiptronic gearbox sometimes sticks

have you had any transmission services done yet? like a flush sounds like a sticking solenoid but very hard to say with out looking into it please rate -jeff

Posted on Sep 01, 2008

  • 1 Answer

SOURCE: AUDI A4 1.8SE WITH AUTO GEARBOX,THE GEARBOX IS VERY SLUGGISH

at speeds below 100km the car accelerates fine. above 100km the reves go up but there is no torque as if car is lazy.
what can this be
Jimmy

Posted on Feb 17, 2010

  • 4793 Answers

SOURCE: I have got a Audi

give the dealer the chassis # (from the lower windshield)and they will order up the right part...

Posted on Aug 17, 2010

  • 38 Answers

SOURCE: had a 94 4g92 in a cb4a replaced with a91

Get computer and engine wire harness

Posted on Aug 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mechanics advised that gearbox needs replace after diagnostic Of codes . Dash light still on after codes being read , have had ecu replaced 2yrs ago ? What do you think it could be , thanks phil


didnt specify vehicle --generic answer--until repair is made the vehicle will show engine light and have codes --if gearbox is problem for limp mode /until repairs are made or gearbox replaced you will be in limp mode --and as to sensor find out what one it was --start problem may show back up if sensor was problem --and GET a 3rd opinion you have 2 mechanics with different opinions on your problem and i guess they are reading your trouble codes differently

Sep 20, 2016 | Cars & Trucks

1 Answer

Auto gearbox not selecting gear


CHECK FOR STORED DTCS AT THE GEARBOX ECU IF POSSIBLE!!DOES THE SHIFT MOVE OR IS ON PARK AND WONT COME OUT?LET ME KNOW!!

Feb 26, 2014 | Audi A4 Cars & Trucks

1 Answer

Free mechanical advice online


Sorry but i would have thought the gearbox would have a different ECU for the gearbox ,Iam a europeon mechanic so auto boxes are few and far between here ,now a diesel manual is more in my line

Apr 22, 2013 | Toyota Cars & Trucks

1 Answer

I have 4jx1 engine manual transmision with manual ecu changed to ecu 4jx1 automatic


The manual and auto ECUs are not interchangeable, the auto ecu needs signals from the auto shifter and gearbox that it is not getting.

Mar 07, 2012 | Isuzu Trooper Cars & Trucks

2 Answers

AUDI A4 1.8SE WITH AUTO GEARBOX,THE GEARBOX IS VERY SLUGGISH


at speeds below 100km the car accelerates fine. above 100km the reves go up but there is no torque as if car is lazy.
what can this be
Jimmy

Dec 09, 2009 | 1997 Audi A4

1 Answer

Software mismatch after changing auto gearbox on 55 reg S80 D5


There are three ecu settings? gearbox / main ecu / and center control, they all will need to be updated then a process called learning cycle which has to be reset by the technicians, then the car needs to be driven to adapt the new transmission.

Mar 16, 2009 | 2006 Volvo S80

1 Answer

Lancer mivec 1.6 loses power at just over 5000rpm oil is fine, engine is warm


Check your oil pressure. Common problem to all 2nd gen MIVEC engine is in its oil sump. A dent could restrict the flow of the engine oil and will cause the engine pressure to drop whenever the MIVEC starting to kick. A low pressure means that the MIVEC system will not activate, hence the low power and no MIVEC "sound".

Oct 09, 2008 | Mitsubishi Lancer Cars & Trucks

1 Answer

LEGACY 2.5 AUTO GEARBOX REPLACEMENT


hi there, needs to be the same number. computers need to match. tourque converters are different from 2.0/2.2 to the 2.5 engines. also shift points are different between models so needs to talk to the dash perfectly. hope this helps.

Jul 18, 2008 | 1994 Subaru Legacy Outdoor

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...